scholarly journals High-Temperature Properties of a Long-Span Double-Deck Suspension Bridge under a Tanker Fire

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Mengsheng Yu ◽  
Qifeng Chen ◽  
Xinyu Yao ◽  
Xiao Guo ◽  
Tianzhi Hao ◽  
...  
Keyword(s):  
High Temperature ◽  
Failure Time ◽  
Numerical Study ◽  
Three Dimensional ◽  
Suspension Bridge ◽  
Element Model ◽  
Steel Plates ◽  
Fire Dynamics ◽  
Long Span ◽  
Upper Deck

This paper presents a numerical study on the high-temperature mechanical properties of a long-span double-deck suspension bridge. The main focus of this paper is the behavior analysis of Wuhan Yangtze River Bridge. A three-dimensional thermal model of the bridge was established by the Fire Dynamics software (FDS) to obtain the 3D temperature field distribution, and the thermal analysis result was then applied to the three-dimensional finite element model of the suspension bridge. The shortest failure time of the main cable and sling was determined to obtain the rescue time of a bridge fire. According to the calculation results of the suspension bridge under a tanker fire initiated at the upper deck of the bridge, the middle lane in the upper deck of the suspension bridge was determined to be a safe lane. Thus, the tanker should be guided to go in this lane of the bridge. The numerical analysis of the experimental results shows that when the fuel tanker is located on the upper and lower floors of the bridge, the bridge structure is affected by the fire. When the oil tanker burns in the outermost lane of the upper bridge, it will have a great impact on the main cables and slings of the bridge. When the fuel tanker burns in the lower nonmotorized lane of the bridge, it will have a great impact on the upper stiffening beam steel plates and truss rods.

Numerical Simulation of Ultimate of Slings for Three-Tower and Four-Span Suspension Bridge under Tanker Fire

2013 ◽  
Vol 361-363 ◽  
pp. 1187-1193
Author(s):  
Mu Yu Liu ◽  
Wei Tian ◽  
Ying Wang ◽  
Wu Jing
Keyword(s):  
Finite Element ◽  
Failure Time ◽  
Three Dimensional ◽  
Fire Risk ◽  
Suspension Bridge ◽  
Element Model ◽  
Prevention Measures ◽  
Heating Curve ◽  
Finite Element Software ◽  
Three Dimensional Finite Element

Three-dimensional finite element model of Yingwuzhou Yangtze river bridge was established by using the finite element software ANSYS. Since the characteristics of bridge fire differed much from that of buildings, Heating curve HCincwas selected as heating curve caused by tanker fire. Heat loading was imposed on the middle of main span where the tanker fire had taken place of three-tower and four-span suspension bridge . The temperature field and stress, modulus of elasticity, strength of sling changing with time caused by tanker burning in midspan were systematically investigated to obtain the failure time of the sling. The calculation also compared the above results of HCinccurve with that of ISO834 curve. This research can provide some references to fire risk prevention measures of bridge during its service life.

scholarly journals Preliminary numerical study on seismic response of ordinary long-span suspension bridges crossing active faults

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Hongyu Jia ◽  
Kang Jia ◽  
Caizhi Sun ◽  
Yanqiang Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Fault Plane ◽  
Numerical Study ◽  
Ground Motions ◽  
Active Faults ◽  
Suspension Bridge ◽  
Element Model ◽  
Suspension Bridges ◽  
Finite Element Software ◽  
Long Span

AbstractThe objective of this paper is to expediently expose the seismic performance pertinent to demand and capacity of general long-span suspension bridges crossing active faults. Firstly three dimensional finite element model of the ordinary long-span suspension bridge is established based on the powerful and attractive finite element software ANSYS. Secondly a series of appropriate fault ground motions with different target final permanent displacements (Tectonic displacements or ground offset) in the direction perpendicular to the fault plane are assumed and applied to the employed long-span suspension bridge. And then the Newmark method is utilized to solve the equation of motion of the long-span suspension bridge structure subjected to fault ground motions in the elastic range. Finally some important conclusions are drawn that the final permanent displacements in the direction perpendicular to the fault plane has significant influence on the seismic responses and demands of general long-span suspension bridges crossing active faults. And the resultant conclusions deliver explicitly and directly specifications and guidelines for seismic design of ordinary long-span suspension bridges across fault-rupture zones.

scholarly journals Probabilistic Assessment of the Safety of Main Cables for Long-Span Suspension Bridges considering Corrosion Effects

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Hao Tian ◽  
Jiji Wang ◽  
Sugong Cao ◽  
Yuanli Chen ◽  
Luwei Li
Keyword(s):  
Probability Model ◽  
Steel Wire ◽  
Suspension Bridge ◽  
Element Model ◽  
Traffic Load ◽  
Suspension Bridges ◽  
Accelerated Corrosion ◽  
Long Span ◽  
Accelerated Corrosion Tests ◽  
Main Cables

This paper presents a reliability analysis to assess the safety of corroded main cables of a long-span suspension bridge. A multiscale probability model was established for the resistance of the main cables considering the length effect and the Daniels effect. Corrosion effects were considered in the wire scale by relating the test results from accelerated corrosion tests to the corrosion stages and in the cable scale by adopting a corrosion stage distribution of the main cable section in NCHRP Report 534. The load effects of temperature, wind load, and traffic load were obtained by solving a finite element model with inputs from in-service monitoring data. The so-obtained reliability index of the main cables reduces significantly after operation for over 50 years and falls below the design target value due to corrosion effects on the mechanical properties of the steel wire. Multiple measures should be taken to delay the corrosion effects and ensure the safety of the main cables in the design service life.

Flutter mitigation of a superlong-span suspension bridge with a double-deck truss girder through wind tunnel tests

2020 ◽  
pp. 107754632094615
Author(s):  
Yanguo Sun ◽  
Yongfu Lei ◽  
Ming Li ◽  
Haili Liao ◽  
Mingshui Li
Keyword(s):  
Wind Tunnel ◽  
Damping Ratio ◽  
Suspension Bridge ◽  
Wind Tunnel Tests ◽  
Long Span Bridges ◽  
Long Span ◽  
Upper Deck ◽  
Torsional Damping ◽  
And Control ◽  
Wind Induced Vibration

As flutter is a very dangerous wind-induced vibration phenomenon, the mitigation and control of flutter are crucial for the design of long-span bridges. In the present study, via a large number of section model wind tunnel tests, the flutter performance of a superlong-span suspension bridge with a double-deck truss girder was studied, and a series of aerodynamic and structural measures were used to mitigate and control its flutter instability. The results show that soft flutter characterized by a lack of an evident divergent point occurred for the double-deck truss girder. Upper central stabilizers on the upper deck, lower stabilizers below the lower deck, and horizontal flaps installed beside the bottoms of the sidewalks are all effective in suppressing flutter for this kind of truss girder. By combining the structural design with aerodynamic optimizations, a redesigned truss girder with widened upper carriers and sidewalks, and double lower stabilizers combined with the inspection vehicle rails is identified as the optimal flutter mitigation scheme. It was also found that the critical flutter wind speed increases with the torsional damping ratio, indicating that the dampers may be efficient in controlling soft flutter characterized by single-degree-of-freedom torsional vibration. This study aims to provide a useful reference and guidance for the flutter design optimization of long-span bridges with double-deck truss girders.

scholarly journals Modeling inflatable fabric with undevelopable surfaces by motion folding method

2019 ◽  
Vol 14 ◽  
pp. 155892501988640
Author(s):  
Xiao-Shun Zhao ◽  
He Jia ◽  
Zhihong Sun ◽  
Li Yu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Numerical Study ◽  
Technical Problem ◽  
Three Dimensional ◽  
Element Model ◽  
Model Errors ◽  
Folding Model ◽  
Study Results ◽  
The Stability

At present, most space inflatable structures are composed of flexible inflatable fabrics with complex undevelopable surfaces. It is difficult to establish a multi-dimensional folding model for this type of structure. To solve this key technical problem, the motion folding method is proposed in this study. First, a finite element model with an original three-dimensional surface was flattened with a fluid structure interaction algorithm. Second, the flattened surface was folded based on the prescribed motion of the node groups, and the final folding model was obtained. The fold modeling process of this methodology was consistent with the actual folding processes. Because the mapping relationship between the original finite element model and the final folding model was unchanged, the initial stress was used to modify the model errors during folding process of motion folding method. The folding model of an inflatable aerodynamic decelerator, which could not be established using existing folding methods, was established by using motion folding method. The folding model of the inflatable aerodynamic decelerator showed that the motion folding method could achieve multi-dimensional folding and a high spatial compression rate. The stability and regularity of the inflatable aerodynamic decelerator numerical inflation process and the consistency of the inflated and design shapes indicated the reliability, applicability, and feasibility of the motion folding method. The study results could provide a reference for modeling complex inflatable fabrics and promote the numerical study of inflatable fabrics.

Numerical Study of Welding Sequence on the Residual Stress Field in a Thick-Walled Tee Joint

2011 ◽  
Vol 219-220 ◽  
pp. 1211-1214
Author(s):  
Wei Jiang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Numerical Study ◽  
Three Dimensional ◽  
Element Model ◽  
Residual Stress Field ◽  
Factors Affecting ◽  
Welding Sequence ◽  
Welding Sequences ◽  
Three Dimensional Finite Element

Finite element simulation is an efficient method for studying factors affecting weld-induced residual stress distributions. In this paper, a validated three-dimensional finite element model consisting of sequentially coupled thermal and structural analyses was developed. Three possible symmetrical welding sequences, i.e. one-welder, two-welder and four-welder sequence, which were perceived to generate the least distortion in actual welding circumstances, were proposed and their influences on the residual stress fields in a thick-walled tee joint were investigated. Appropriate conclusions and recommendations regarding welding sequences are presented.

Study of arching behaviour and strength of concrete masonry infills under out-of-plane loading

2019 ◽  
Vol 46 (10) ◽  
pp. 896-908 ◽  
Author(s):  
Ehsan Nasiri ◽  
Yi Liu
Keyword(s):  
Numerical Study ◽  
Three Dimensional ◽  
Element Model ◽  
Contributing Factors ◽  
Concrete Frames ◽  
Masonry Infills ◽  
Concrete Masonry ◽  
Wide Range ◽  
Out Of Plane ◽  
Three Dimensional Finite Element

A numerical study using a three-dimensional finite element model was conducted to investigate the arching behaviour and strength of concrete masonry infills bounded by reinforced concrete frames subjected to out-of-plane loading. Physical specimens were concurrently tested to provide results for validation of the model as well as evidence of directional characteristics of arching behaviour of masonry infills. A subsequent parametric study using the model included a wide range of infilled frame geometric properties. The results showed in detail the difference in one-way and two-way arching in terms of both strength and failure mechanism, and the contributing factors to this difference. Evaluation of the two main design equations for out-of-plane strength of masonry infills led to proposal of modifications to provide a more rational consideration of directional behaviour of concrete masonry infills. A comparison study using the available test results showed a marked improvement of strength prediction based on the proposed modification.

scholarly journals STUDY ON NONLINEAR PAVEMENT RESPONSES OF LOW VOLUME ROADWAYS SUBJECT TO MULTIPLE WHEEL LOADS / NETIESINĖS KELIO DANGOS PRIKLAUSOMYBĖS NUO MAŽO INTENSYVUMO KELIŲ, VEIKIAMŲ DAUGKARTINĖMIS RATŲ APKROVOMIS, TYRIMAS

2011 ◽  
Vol 17 (1) ◽  
pp. 45-54 ◽  
Author(s):  
Minkwan Kim ◽  
Joo Hyoung Lee
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Asphalt Pavement ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Nonlinear Stress ◽  
Low Volume ◽  
Stress Dependent

This paper describes numerical analyses on low volume roads (LVRs) using a nonlinear three-dimensional (3D) finite element model (FEM). Various pavement scenarios are analyzed to investigate the effects of pavement layer thicknesses, traffic loads, and material properties on pavement responses, such as surface deflection and subgrade strain. Each scenario incorporates a different combination of wheel/axle configurations and pavement geomaterial properties to analyze the nonlinear behavior of thinly surfaced asphalt pavement. In this numerical study, nonlinear stress-dependent models are employed in the base and subgrade layers to properly characterize pavement geomaterial behavior. Finite element analysis results are then described in terms of the effects of the asphalt pavement thickness, wheel/axle configurations, and geomaterial properties on critical pavement responses. Conclusions are drawn by the comparison of the nonlinear pavement responses in the base and subgrade in association with the effects of multiple wheel/axle load interactions. Santrauka Straipsnyje aprašoma skaitinė mažo intensyvumo kelių analizė, taikant netiesinį—erdvinį baigtinių elementų modelį. Skirtingi dangų paviršiaus variantai analizuojami siekiant ištirti, kokiąįtaką kelio dangos elgsenai, t. y. poslinkiams ir kelio pagrindo deformacijoms, turi dangų sluoksnių storiai, eismo apkrovos ir medžiagų savybės. Kiekvienas kelio dangos variantas turi skirtingas ratų arba ašies ir geometrinių savybių formas, kad būtų galima išanalizuoti netiesinę plonos asfalto dangos paviršiaus elgseną. Šioje skaitinėje analizėje nagrinėjami netiesiniai įtempių modeliai, kurie buvo taikomi pagrindo sluoksniams, siekiant tinkamai apibūdinti geometrinę kelio dangos elgseną. Baigtinių elementų analizės rezultatai toliau nagrinėjami atsižvelgiant į asfalto dangos storį ar ašies formą ir geometrines savybes, priklausomai nuo kritinės kelio dangos būklės. Išvados buvo gautos lyginant netiesines kelių dangos priklausomybes pagrindo sluoksnyje, atsižvelgiant į jų sąveiką su daugkartine ratų apkrova.

Numerical Study on the Effect of Twin-Tube Shield Excavation on Adjacent Pipelines

2012 ◽  
Vol 170-173 ◽  
pp. 1491-1496 ◽  
Author(s):  
Xin Wang ◽  
De Shen Zhao ◽  
Meng Lin Xu
Keyword(s):  
Distribution Curve ◽  
Numerical Study ◽  
Three Dimensional ◽  
Element Model ◽  
Stress Release ◽  
Tunnel Excavation ◽  
Normal Distribution Curve ◽  
Numerical Result ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Based on Dalian subway line 2 from Chun-guang street station to Xiang-gong street station,the three dimensional finite element model was established using FLAC3D software , the shield excavated surface against the pressure, the stress release, the shield tail escape and grouting. The numerical result indicated that the pipeline displacement increases gradually with the advance of the tunnel excavation. When one-sided tunnel excavation is carried out, the largest displacement is located at the tunnel axis, the settling curve basically conforms to the normal distribution curve with the unimodal characteristic. The excavation of right-side tunnel is disadvantageous to the left-side tunnel. The analysis indicated that the pipeline is in a secure state. The work in this paper provided theoretical basis and the practical guidance to this project.

Behaviour and design of composite beams with composite slabs at elevated temperatures

2016 ◽  
Vol 20 (10) ◽  
pp. 1451-1465 ◽  
Author(s):  
Shou-Chao Jiang ◽  
Gianluca Ranzi ◽  
Ling-Zhu Chen ◽  
Guo-Qiang Li
Keyword(s):  
Elevated Temperatures ◽  
Numerical Study ◽  
Three Dimensional ◽  
Structural Response ◽  
Load Ratio ◽  
Element Model ◽  
Composite Beams ◽  
European Guidelines ◽  
Design Fire ◽  
Composite Slabs

This article presents an extensive experimental and numerical study aimed at the evaluation of the thermo-structural response of composite beams with composite slabs. Two full-scale fire tests were carried out on simply supported composite steel-concrete beams with steel sheeting perpendicular and parallel to the steel joist, respectively. Both specimens were observed to fail by developing large displacements. Concrete crushing at the mid-span, debonding of the profiled sheeting and spalling of the fire protection were observed during both tests. A three-dimensional finite element model was developed in ABAQUS, and its accuracy was validated against the experimental measurements collected as part of this study. The model was then used to perform a parametric study to determine the influence of the degree of shear connection, load ratio and design fire rate on the structural response of composite beams at elevated temperatures. These results, together with experimental data available in the literature, were used to evaluate the ability of European guidelines to predict the critical temperature of composite beams. It was shown that predictions from Eurocode 4 were safe and provided conservative estimates for most cases.

Sign in / Sign up

Export Citation Format

Share Document