scholarly journals Mechanical Properties of Concrete Incorporating Rice Husk Ash and Wheat Straw Ash as Ternary Cementitious Material

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Naraindas Bheel ◽  
Paul Awoyera ◽  
Irfan Ali Shar ◽  
Samiullah Sohu ◽  
Suhail Ahmed Abbasi ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
Wheat Straw ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Drying Shrinkage ◽  
Cementitious Material ◽  
Straw Ash

Over the last decade, there has been a surge in research into possible cement substitute materials in concrete that are environmentally friendly, cost-effective, and socially beneficial. The alternatives include industrial and agricultural wastes, and their potential advantages can be achieved through recycling, repurposing, and renewing processes. With the use of these wastes as additional and replacement materials, significant energy savings and a reduction in cement use can be achieved, which helps to reduce carbon dioxide (CO2) emissions in the environment. Therefore, the use of rice husk ash (RHA) and wheat straw ash (WSA) as ternary cementitious material (TCM) in concrete can help reduce the impact on the environment and minimize the use of Portland cement (PC) in the concrete mixture. This research work is performed on the concrete blended with 0%, 5%, 10%, 15%, and 20% of RHA and WSA as TCM in the mixture. However, the purpose of this experimental work is to investigate the influence of RHA and WSA as TCM on the fresh (slump), physical (water absorption and density), and hardened properties (compressive strength, splitting tensile strength, and flexural strength) and drying shrinkage of concrete. In this regard, a total of 240 concrete samples (cylinders, cubes, and beams) were prepared with 1 : 2 : 4 mix proportions at 0.50 water-cement ratio and cured at 7 and 28 days, respectively. Moreover, the workability of green concrete is getting reduced as the quantity of TCM increases in the mixture. Besides, the compressive strength, splitting tensile strength, and flexural strength are enhanced by 12.65%, 9.40%, and 9.46% at 10% of TCM (5% RHA and 5% WSA) on 28 days consistently. Furthermore, the density and water absorption of concrete are reduced with the increase in the dosages of TCM on 28 days, respectively. In addition, the drying shrinkage is reduced with the increase in the quantity of TCM in concrete.

scholarly journals Use of Rice Husk Ash as Cementitious Material in Concrete

2019 ◽  
Vol 9 (3) ◽  
pp. 4209-4212 ◽  
Author(s):  
N. Bheel ◽  
A. W. Abro ◽  
I. A. Shar ◽  
A .A. Dayo ◽  
S. Shaikh ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Rice Husk ◽  
Industrial Waste ◽  
Rice Husk Ash ◽  
Fresh Concrete ◽  
Cementitious Material ◽  
Target Strength ◽  
Alternative Processing ◽  
Concrete Properties

In this research, rice husk ash (RHA) was used as a partial substitute for cement in concrete to reduce its cost, and alternative processing methods using agricultural/industrial waste were found. The main objective of this study was to determine the fresh (flowability) and hardened (splitting tensile strength and compressive strength) concrete properties using RHA at 0%, 5%, 10%, 15% and 20% by weight. A total of 90 concrete samples (45 cubes and 45 cylinders) were prepared and cured on 7, 14, and 28 days to the design of target strength 28N/mm2, and ultimately, these concrete specimens were tested on UTM. Three concrete specimens were cast for each proportion and ultimately the average of the three concrete samples was taken as the final result. The flowability of fresh concrete decreases with increasing content of RHA in concrete. The results showed that the compressive and tensile strength of the concrete specimens increased by 11.8% and 7.31%, respectively by using 10% RHA at 28 days curing.

scholarly journals Strength Characteristics of Cement-Rice Husk Ash Stabilised Sand-Clay Mixture Reinforced with Polypropylene Fibers

2018 ◽  
Vol 13 (4) ◽  
pp. 447-474 ◽  
Author(s):  
Ali Ghorbani ◽  
Maysam Salimzadehshooiili ◽  
Jurgis Medzvieckas ◽  
Romualdas Kliukas
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Rice Husk ◽  
Unconfined Compressive Strength ◽  
Rice Husk Ash ◽  
Indirect Tensile Strength ◽  
Polypropylene Fibres ◽  
Indirect Tensile ◽  
Improvement Index

In this paper, stress-strain behaviour of sand-clay mixture stabilised with different cement and rice husk ash percentages, and reinforced with different polypropylene fibre lengths are evaluated. Mixtures are widely used in road construction for soil stabilisation. It is observed that replacing half of the cement percentage (in high cement contents) with rice husk ash will result in a higher unconfined compressive strength. In addition, the presence of 6 mm polypropylene fibres will help to increase the unconfined compressive strength of stabilised samples, while larger fibres cause reverse behaviour. In addition, introducing a new index for assessing the effect of curing days. Curing Improvement Index it is obtained that larger fibres show higher Curing Improvement Index values. Results gained for the effects of curing days, and fibre lengths are further discussed and interpreted using Scanning Electron Microscopy photos. Based on the conducted Unconfined Compressive Strength, Indirect Tensile Strength, and Flexural Strength tests and using evolutionary polynomial regression modelling, some simple relations for prediction of unconfined compressive strength, indirect tensile strength, and flexural strength of cement-rice husk ash stabilised, and fibre reinforced samples are presented. High coefficients of determination of developed equations with experimental data show the accuracy of proposed relationships. Moreover, using a sensitivity analysis based on Cosine Amplitude Method, cement percentage and the length of polypropylene fibres used to reinforce the stabilised samples are respectively reported as the most and the least effective parameters on the unconfined compressive strength of specimens.

Investigation on the Use of Fly Ash and Residual Rice Husk Ash for Producing Unfired Building Bricks

2015 ◽  
Vol 752-753 ◽  
pp. 588-592 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Potential Use

This paper reports on the potential use of fly ash (FA) and residual rice husk ash (RHA) in producing unfired building bricks (UBB) with the application of densified mixture design algorithm (DMDA) method. In this study, little amount of cement (10–15%) was added into the mixtures as binder substitution. Whereas, unground rice husk ash (URHA), an agricultural by-product, was used as partial aggregate replacement (10–20%) in the mixtures. The UBB of 220×105×60 mm in size were prepared and the hardened properties of the bricks were tested including compressive strength, flexural strength, water absorption and bulk density according to Vietnamese standard. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens achieved very good mechanical properties. The compressive strength, flexural strength and water absorption of brick specimens were respectively in range of 16.1–22.1 MPa, 2.8–3.5 MPa and 9.5–14.8% and the other properties of the bricks were well conformed to related Vietnamese standard. It was definitely proved many potential applications of FA and RHA in the production of UBB.

scholarly journals Properties of concrete using crumb rubber and rice husk ash as additive for rigid pavement material in peat environment

2019 ◽  
Vol 276 ◽  
pp. 01020 ◽  
Author(s):  
Habib Abdurrahman ◽  
Mia Qoryati ◽  
Muklisin Olivia ◽  
Monita Olivia
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Elastic Properties ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Crumb Rubber ◽  
Rigid Pavement ◽  
Waste Tyre

A waste tyre is an inorganic rubber waste that is difficult to decompose since it has a complex structure. Utilization of waste tyre as a material to improve elastic properties in rigid pavement construction in peat environment has not investigated yet. The rigid pavement in peat environment needs to be impermeable and posses high elastic properties. This paper presents mechanical properties and porosity of concrete incorporating crumb rubber as an additive in concrete mixture with a variation of 10%, 20%, and 30% by fine aggregates volume. Rice husk ash is added as a filler in various percentage (5%, 10%, and 15%) by cement volume in the mixture. Concrete is produced with a target strength of 35 MPa. In this research, the OPC concrete mix is used as a control mix. Mechanical properties taken were the compressive strength, tensile strength, flexural strength, modulus of elasticity, and porosity at 7, 14 and 28 days. Results show that crumb rubber and rice husk ash addition increases compressive strength, improves elastic properties, i.e., tensile strength, flexural strength, modulus of elasticity, and reduce the porosity of the concrete. It can be concluded that the crumb rubber is potential as an environmentally friendly additive as rigid pavement material in peat environment.

scholarly journals Influences of shrinkage reducing admixture on the mechanical properties, drying shrinkage, water absorption and porosity of Portland cement mortar

2021 ◽  
Vol 15 (3) ◽  
pp. 55-67
Author(s):  
Nguyen Van Chinh
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Drying Shrinkage ◽  
Effective Porosity ◽  
Minor Effect ◽  
Wide Range ◽  
Shrinkage Reducing Admixture ◽  
A Minor

Drying shrinkage is the main cause of early age cracking of concrete and mortar. A wide range of research has been conducted to reduce the drying shrinkage, including using fibres or chemical admixtures. This paper investigated the effect of shrinkage reducing admixture on the flexural strength, compressive strength, drying shrinkage, water absorption and porosity of mortar. The mix compositions were ordinary Portland cement (OPC) : sand : liquid = 1: 1: 0.38 in which liquid consisted of water and shrinkage reducing admixture (SRA). SRA was used at the proportions of 2%, 4%, and 7% by weight of cement. The test results show that SRA reduces the flexural and compressive strengths of mortar. The reduction in flexural strength and compressive strength at 28 days is 14% and 25%, respectively at 7% SRA dosage. In addition, SRA significantly reduces the drying shrinkage and water absorption of mortar. At 7% SRA dosage, the drying shrinkage at 53 days is reduced by 60% while the water absorption rate at 24 hours is reduced by 54%. However, SRA has a minor effect on the pore size distribution, effective porosity, and cumulative intrusion volume of mortar.

scholarly journals Hydrochloric Acid Pretreatment of Different Types of Rice Husk Ash Influence on the Properties of Cement Paste

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1524 ◽  
Author(s):  
Jing Liu ◽  
Chunyan Xie ◽  
Chao Fu ◽  
Xiuli Wei ◽  
Dake Wu
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Cement Paste ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Control Sample ◽  
Control Group ◽  
Rice Husks ◽  
Acid Pretreatment ◽  
Blank Control Group

When properly processed, rice husk ash (RHA) comprises a large amount of SiO2, which exhibits a high pozzolanic activity and acts as a good building filler. In this paper, the effects of rice husk ash content, acid pretreatment, and production regions on the compressive and flexural properties and water absorption of a cement paste were studied. The experimental results showed that the compressive strength of the rice husk ash was the highest with a 10% content level, which was about 16.22% higher than that of the control sample. The rice husk after acid pretreatment displayed a higher strength than that of the sample without the acid treatment, and the rice husk from the Inner Mongolia region indicated a higher strength than that from the Guangdong province. However, the flexural strength of each group was not significantly different from that of the blank control group. The trend observed for the water absorption was similar to that of the compressive strength. The variation in the RHA proportions had the greatest influence on the properties of the paste specimens, followed by the acid pretreatments of the rice husks. The production regions of the rice husks indicated the least influence.

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

The Study on Physical and Thermal Properties of Geopolymer Pastes

2017 ◽  
Vol 751 ◽  
pp. 538-543 ◽  
Author(s):  
Pongsak Jittabut
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Bulk Density ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Weight Ratio ◽  
Thermal Capacity

This research was aimed to a present the physical and thermal properties of geopolymer pastes made of fly ash (FA) and bagasse ash (BA) with rice husk ash (RHA) containing at the doses of 0%, 2%, 4%, 6%, 8% and 10% by weight. The sodium hydroxide concentration of 15 molars, sodium silicate per sodium hydroxide by weight ratio of 2.0, the alkaline liquid per binder at the ratio of 0.60 and curing at ambient temperature were used at the to mix all mixtures to gether for 7 and 28 days. The properties analysis of the geopolymer pastes such as compressive strength, bulk density, water absorption, thermal conductivity, thermal diffusivity and thermal capacity were tested. The results were indicated that geopolymer pastes that containing rice husk ash 2% by weight for 28 days of curing gave the maximum compressive strength of 84.42 kg/cm2, low water absorption of 1.16 %, low bulk density of 2,065.71 kg/cm3, lower thermal conductivity of 1.1173 W/m.K, lower thermal diffusion of 6.643 µm2/s and lower thermal capacity of 1.6819 MJ/m3K, respectively. The utilization of waste from agriculture industry via geopolymer pastes for green building materials can be achieved. For this research, physical properties and thermal insulation of geopolymer pastes were siqnificantly improved.

scholarly journals Study of Fly Ash, Rice Husk Ash and Marble Powder as Partial Replacement to Cement in Concrete

2020 ◽  
Vol 13 (3) ◽  
pp. 315-321
Author(s):  
Dhiraj Ahiwale ◽  
Rushikesh Khartode
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Scale Production ◽  
Environmental Threat ◽  
Marble Powder

Now days, the waste rice husk from rice mill, marble powder from tile industry and fly ash from steam power plant are necessary to utilize as partial replacement of cement for concrete production. Large scale production of cement required consumption of raw materials and energy as well as emissions to air which posse’s environmental threat in various areas of country. Apart from the environmental threat, there still exists the problem of shortage in many areas. Therefore, substitute material for concrete needs to be considered. The paper aims to analyze the compressive strength of concrete cubes and flexural strength of concrete beams made from partially replaced cement, sand, and coarse aggregate. This research study adopted in laboratory on 48 total specimens of grade M25 concrete cubes of size 150x150x150mm and concrte beams of size 100x100x500mm were casted. Out of the 48 concrete specimens cast, 6 each were made out 10%, 20%, and 30 % replacement of fly ash, rice husk ash and marble powder to cement in concrete. It was found that the compressive strength and flexural strength of concrete made from the mixture of 20 % partially replaced cement, sand and coarse aggregate was similar than the concrete made from without replaced cement , sand and coarse aggregate.

Properties Evaluation of Repair Mortars Containing EVA and VA/VeoVa Polymer Powders

2017 ◽  
Vol 25 (1) ◽  
pp. 77-86 ◽  
Author(s):  
Tsai-Lung Weng ◽  
Wei-Ting Lin ◽  
Cheng-Hao Li
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Thermal Expansion ◽  
Flexural Strength ◽  
Bond Strength ◽  
Drying Shrinkage ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Repair Materials ◽  
Repair Mortars

The repair of damaged structures is a complicated problem in the construction industry and it is no uniform standard for evaluating the effectiveness of repair materials. Two different redispersible polymer powders, ethylene vinyl acetate (EVA) and polyvinyl acetate-vinyl carboxylate (VA/VeoVa), were added in the repair mortars with two water-cement ratios and three polymer-cement ratios. The effectiveness of repair materials was evaluated according to the physical, mechanical properties and micrographs. Testing program includes setting time, drying shrinkage, thermal expansion, compressive strength, tensile strength, flexural strength, bond strength, X-ray diffraction analysis, scanning electron microscopy observation. Test results show that the specimens with VA/VeoVa and w/c of 0.5 have highest compressive strength, tensile strength, flexural strength and bond strength. The specimen with EVA also has higher strength than control one at the age of 28 days. The drying shrinkage deformation of VA/VeoVa specimen is close to the control one. The specimens with VA/VeoVa have lower thermal expansion than EVA specimen when the water-cement ratio is 0.5 and there is no difference between EVA and VA/VeoVa specimens for the water-cement ratio of 0.6. The micrographs show that adding polymer powder can reduce the pore and improve the durability.

Sign in / Sign up

Export Citation Format

Share Document