scholarly journals Numerical Simulation of the Volumetric Strain Distribution of a Protected Coal Seam

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Hengyi Jia
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Strain Distribution ◽  
Volumetric Strain ◽  
Distribution Characteristics ◽  
Permeability Enhancement ◽  
Working Face ◽  
Coal Pillars ◽  
Definition Of ◽  
Seam Mining

To investigate the deformation characteristics of protected coal seams, the numerical simulation of the mining of an upper protective coal seam was carried out in the present study. Based on the basic definition of strain, a method for the extraction of the strain data of the protected coal seam was proposed, and the strain distribution characteristics were obtained. It was found that the x -direction strain is mainly distributed near the coal pillars on both sides and inside the goaf, the y -direction strain is mainly distributed at the working face, the initial mining line, and inside the goaf, and the z -direction strain is mainly distributed at the working face, the initial mining line, the coal pillars on both sides, and inside the goaf. The distribution characteristics and the value of volumetric strain were found to be basically consistent with the z -direction strain. As the working face advances, the protected coal seam undergoes compression and damage expansion in turn. The turning point between compression and damage expansion is approximately 15 m in front of the working face. The variation law of gas drainage in the boreholes of the protected coal seam is closely related to the distribution characteristics of volumetric strain. The results of this research are of great significance for the comprehensive investigation of the effects of pressure relief and the permeability enhancement of protective coal seam mining.

scholarly journals A Mechanical Model of the Overlying Rock Masses in Undersea Coal Mining and a Stress-Seepage Coupling Numerical Simulation

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jie Fang ◽  
Lei Tian ◽  
Yanyan Cai ◽  
Zhiguo Cao ◽  
Jinhao Wen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Coal Mining ◽  
Water Inrush ◽  
Mining Area ◽  
Analysis Model ◽  
Fractured Zones ◽  
Working Face ◽  
Seam Mining ◽  
Overlying Strata

The water inrush of a working face is the main hidden danger to the safe mining of underwater coal seams. It is known that the development of water-flowing fractured zones in overlying strata is the basic path which causes water inrushes in working faces. In the engineering background of the underwater mining in the Longkou Mining Area, the analysis model and judgment method of crack propagation were created on the basis of the Mohr–Coulomb criterion. Fish language was used to couple the extension model into the FLAC3d software, in order to simulate the mining process of the underwater coal seam, as well as to analyze the initiation evolutionary characteristics and seepage laws of the fractured zones in the overlying strata during the advancing processes of the working face. The results showed that, during the coal seam mining process, the mining fractured zones which had been caused by the compression-shear and tension-shear were mainly concentrated in the overlying strata of the working face. Also, the open-off cut and mining working face were the key sections of the water inrush in the rock mass. The condition of the water disaster was the formation of a water inrush channel. The possible water inrush channels in underwater coal mining are mainly composed of water-flowing fractured zones which are formed during the excavation processes. The numerical simulation results were validated through the practical engineering of field observations on the height of water-flowing fractured zone, which displayed a favorable adaptability.

scholarly journals Failure Mechanism and Control Technology of Thick and Soft Coal Fully Mechanized Caving Roadway under Double Gobs in Close Coal Seams

2020 ◽  
Vol 2020 ◽  
pp. 1-23
Author(s):  
Shengrong Xie ◽  
Xiaoyu Wu ◽  
Dongdong Chen ◽  
Yaohui Sun ◽  
En Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Field Distribution ◽  
Control Technology ◽  
Coal Seams ◽  
Anchor Bolt ◽  
Anchor Cable ◽  
Coal Pillars ◽  
Seam Mining ◽  
And Control

The surrounding rock of the roadway under double gobs in the lower coal seams is partially damaged by the mining of the upper coal seam and the stress superimposition of the stepped coal pillars. What is worse, the upper layer of the roof is collapse gangue in double gobs, which makes the anchor cable unable to anchor the reliable bearing layer, so the anchoring performance is weakened. The actual drawing forces of the anchor bolt and anchor cable are only approximately 50 kN and 80 kN, respectively. The roadway develops cracks and large deformations with increasing difficulty in achieving safe ventilation. In view of the above problems, taking the close coal seam mining in the Zhengwen Coal Mine as the engineering background, a theoretical calculation is used to obtain the loading of the step coal pillars and the slip line field distribution of the floor depth. The numerical simulation monitors the stress superimposition of stepped coal pillars and the distribution of elastoplastic areas to effectively evaluate the layout of mining roadways. The numerical simulation also analyzes the effective prestress field distribution of the broken roof and grouting roof anchor cable. A laboratory test was used to monitor the strength of the grouting test block of the broken coal body. Then, we proposed that grouting anchor cable be used to strengthen the weak surface of the roof and block the roof cracks. From on-site measurement, the roadway was seen to be arranged in the lateral stress stabilization area of the stepped coal pillars, the combined support technology of the grouting anchor cable (bolt) + U type steel + a single prop was adopted, the roadway deformation was small, the gas influx was reduced, and the drawing force of the anchor bolt and the anchor cable was increased to approximately 160 kN and 350 kN, respectively. The overall design and control technology of the roadway can meet the site safety and efficient production requirements.

scholarly journals Analysis on Rock Burst Risks and Prevention of a 54 m-Wide Coal Pillar for Roadway Protection in a Fully Mechanized Top-Coal Caving Face

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Zhihua Li ◽  
Ke Yang ◽  
Jianshuai Ji ◽  
Biao Jiao ◽  
Xiaobing Tian
Keyword(s):  
Coal Seam ◽  
Rock Burst ◽  
Influencing Factors ◽  
Abutment Pressure ◽  
Large Diameter ◽  
Coal Pillar ◽  
Distribution Characteristics ◽  
Pressure Relief ◽  
Working Face ◽  
Coal Pillars

A case study based on the 401103 fully mechanized caving face in the Hujiahe Coal Mine was carried out in this research to analyze the rock burst risks in a 54 m-wide coal pillar for roadway protection. Influencing factors of rock burst risks on the working face were analyzed. Stress distribution characteristics on the working face of the wide coal pillar for roadway protection were discussed using FLAC3D numerical simulation software. Spatial distribution characteristics of historical impact events on the working face were also investigated using the microseismic monitoring method. Results show that mining depth, geological structure, outburst proneness of coal strata, roof strata structure, adjacent mining area, and mining influence of the current working face are the main influencing factors of rock burst on the working face. Owing to the collaborative effects of front abutment pressure of the working face and lateral abutment pressure in the goaf, the coal pillar is in the ultimate equilibrium state and microseismic events mainly concentrate in places surrounding the coal pillars. Hence, wide coal pillars become the regions with rock burst risks on the working face. The working face adopts some local prevention technologies, such as pressure relief through presplitting blasting in roof, pressure relief through large-diameter pores in coal seam, coal seam water injection, pressure relief through large-diameter pores at bottom corners, and pressure relief through blasting at bottom corners. Moreover, some regional prevention technologies were proposed for narrow coal pillar for roadway protection, including gob-side entry, layer mining, and fully mechanized top-coal caving face with premining top layer.

scholarly journals Study on the Law of Fracture Evolution under Repeated Mining of Close-Distance Coal Seams

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 6064
Author(s):  
Feng Cui ◽  
Chong Jia ◽  
Xingping Lai ◽  
Yanbing Yang ◽  
Shuai Dong
Keyword(s):  
Coal Seam ◽  
Short Distance ◽  
Coal Pillar ◽  
Mineral Resources ◽  
Expansion Rate ◽  
Distribution Characteristics ◽  
Lower Section ◽  
Working Face ◽  
Adjacent Face ◽  
Coal Pillars

The western region of China is rich in mineral resources. The vigorous development of mineral resources has exacerbated the environmental and safety problems in the region. One of the important links to solve this problem is to control the development laws and distribution characteristics of the overburdened cracks in the mining of this area. In this paper, the Xiashijie coal mine 3-2 coal seam and 4-2 coal seam are examples of repeated mining, and are examined as the background, through theoretical analysis to optimize the size of the coal pillars in the lower section, using the 3DEC numerical simulation experiment method and the rise of the cracks in the short-distance coal seam. Repeated mining monitoring and analysis of the development law are used to ascertain distribution characteristics of overburdened cracks caused by the repeated mining process of the working face. The results show that: (1) By establishing a mechanical model of the overlying strata structure under short-distance coal seam group mining, and carrying out the force analysis of the double section coal pillar under repeated mining, the reasonable size of a lower section coal pillar was determined to be 70 m. (2) As the development height of a fracture progresses with the working face, its expansion rate undergoes four obvious changes: fluctuations within a certain range, the expansion rate reaches the peak after the rock formation is concentrated and broken, the cyclical change gradually decreases, and the expansion rate is zero after complete mining. (3) The fracture zone height of 222 and 224 face under repeated mining in the 4-2 coal seam was 19.56–22.31 times and 22.38–24.54 times larger, respectively, and the post-mining fracture extension of the face with larger width and deeper burial under repeated mining was higher than that of the adjacent face. This study provides scientific guidance for the rational division of coal pillars and the solution of the problem of water conservation mining under repeated mining in the adjacent face of a short-distance coal seam.

scholarly journals Permeability Enhancement and Gas Drainage Effect in Deep High Gassy Coal Seams via Long-Distance Pressure Relief Mining: A Case Study

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Xiang He ◽  
Ke Yang ◽  
Penghua Han ◽  
Wenjie Liu ◽  
Zhonghao Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Protective Layer ◽  
Enhancement Effect ◽  
Yield Model ◽  
Long Distance ◽  
Pressure Relief ◽  
Gas Drainage ◽  
Permeability Enhancement ◽  
Seam Mining

Coal 3 in group A is employed as a protective layer to release long-distance coal 4 in group B in Paner colliery (approximately 80 m vertical interval) as the mining depth extends downward, which is the first engineering test in the Huainan coal mining area. To evaluate the validity of the scheme, the permeability distribution, and evolution law, gas pressure distribution characteristics, swelling deformation, pressure relief range, and gas drainage volume of the protected coal seam are analyzed using a FLAC3D numerical simulation and field measurements. Therefore, different stress-permeability models are adopted for caved, fractured, and continuous deformation zones, and a double-yield model is applied in the goaf based on compaction theory to improve the accuracy of the numerical simulation. The results indicate that the extraction of coal 3 has a positive effect on permeability enhancement and pressure relief gas drainage. However, the dip angle of coal measurements causes asymmetric strata movement, which leads to the pressure relief and permeability enhancement area shifting to the downhill side, where the permeability enhancement effect of the downhill side is better than that of the uphill side. The permeability enhancement zone is an inverted trapezoid, but the effective pressure relief range is a positive trapezoid. The permeability of the protected coal seam in the pressure relief zone is significantly higher than that in the compressive failure zone. The permeability in the pressure relief zone will decrease again due to the recompaction of the coal seam with an advancement of the longwall face. Thus, pressure relief gas drainage is suggested during long-distance protective coal seam mining to eliminate gas hazards.

Forecast of Methane Emission on the Working Face at Coal Seam Mining

2017 ◽  
Vol 6 ◽  
pp. 31-35
Author(s):  
V.S. Zaburdayev ◽  
Keyword(s):  
Coal Seam ◽  
Methane Emission ◽  
Working Face ◽  
Seam Mining

Reasonable Entry Layout of Lower Seam in Multi-Seam Mining Based on Numerical Simulation

2013 ◽  
Vol 295-298 ◽  
pp. 2980-2984
Author(s):  
Xiang Qian Wang ◽  
Da Fa Yin ◽  
Zhao Ning Gao ◽  
Qi Feng Zhao
Keyword(s):  
Numerical Simulation ◽  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mine ◽  
Abutment Pressure ◽  
Surrounding Rock ◽  
Geological Conditions ◽  
Seam Mining

Based on the geological conditions of 6# coal seam and 8# coal seam in Xieqiao Coal Mine, to determine reasonable entry layout of lower seam in multi-seam mining, alternate internal entry layout, alternate exterior entry layout and overlapping entry layout were put forward and simulated by FLAC3D. Then stress distribution and displacement characteristics of surrounding rock were analyzed in the three ways of entry layout, leading to the conclusion that alternate internal entry layout is a better choice for multi-seam mining, for which makes the entry located in stress reduce zone and reduces the influence of abutment pressure of upper coal seam mining to a certain extent,. And the mining practice of Xieqiao Coal Mine tested the results, which will offer a beneficial reference for entry layout with similar geological conditions in multi-seam mining.

scholarly journals A numerical simulation of realistic top coal caving intervals under different top coal thicknesses in longwall top coal caving working face

2021 ◽  
Author(s):  
Chuang Liu ◽  
Huamin Li
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Distinct Element ◽  
Simulation Models ◽  
Simulation Software ◽  
Thick Coal Seam ◽  
Coal Recovery ◽  
Working Face ◽  
Longwall Top Coal Caving ◽  
Selection Of

Abstract In the process of longwall top coal caving, the selection of the top coal caving interval along the advancing direction of the working face has an important effect on the top coal recovery. To explore a realistic top coal caving interval of the longwall top coal caving working face, longwall top coal caving panel 8202 in the Tongxin Coal Mine is used as an example, and 30 numerical simulation models are established by using Continuum-based Distinct Element Method (CDEM) simulation software to study the top coal recovery with 4.0 m, 8.0 m, 12.0 m, 16.0 m, 20.0 m and 24.0 m top coal thicknesses and 0.8 m, 1.0 m, 1.2 m, 1.6 m and 2.4 m top coal caving intervals. The results show that with an increase in the top coal caving interval, the single top coal caving amount increases. The top coal recovery is the highest with a 0.8 m top coal caving interval when the thickness of the top coal is less than 4.0 m, and it is the highest with a 1.2 m top coal caving interval when the coal seam thickness is greater than 4.0 m. These results provide a reference for the selection of a realistic top coal caving interval in thick coal seam caving mining.

scholarly journals Surrounding Rock Movement of Steeply Dipping Coal Seam Using Backfill Mining

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Wenyu Lv ◽  
Kai Guo ◽  
Jianhao Yu ◽  
Xufeng Du ◽  
Kun Feng
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Surrounding Rock ◽  
Maximum Deflection ◽  
Coal Seams ◽  
Physical Similarity ◽  
Working Face ◽  
Rock Structure ◽  
Backfill Mining ◽  
The Stability

The movement of the overlying strata in steeply dipping coal seams is complex, and the deformation of roof rock beam is obvious. In general, the backfill mining method can improve the stability of the surrounding rock effectively. In this study, the 645 working face of the tested mine is used as a prototype to establish the mechanical model of the inclined roof beam using the sloping flexible shield support backfilling method in a steeply dipping coal seam, and the deflection equation is derived to obtain the roof damage structure and the maximum deflection position of the roof beam. Finally, numerical simulation and physical similarity simulation experiments are carried out to study the stability of the surrounding rock structure under backfilling mining in steeply dipping coal seams. The results show the following: (1) With the support of the gangue filling body, the inclined roof beam has smaller roof subsidence, and the maximum deflection position moves to the upper part of working face. (2) With the increase of the stope height, the stress and displacement field of the surrounding rock using the backfilling method show an asymmetrical distribution, the movement, deformation, and failure increase slowly, and the increase of the strain is relatively stable. Compared with the caving method, the range and degree of the surrounding rock disturbed by the mining stress are lower. The results of numerical simulation and physical similarity simulation experiment are generally consistent with the theoretically derived results. Overall, this study can provide theoretical basis for the safe and efficient production of steeply dipping coal seams.

Sign in / Sign up

Export Citation Format

Share Document