scholarly journals Evaluation of Freeze-Thaw Durability of Silica Fume Concrete with Spraying Inorganic Coating Using Ultrasonic Testing

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Wujian Yan ◽  
Fuhang Niu ◽  
Xinxin Tian
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Testing ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Freeze Thaw ◽  
Strength Tests ◽  
Inorganic Coating ◽  
External Coating

To study the antifreezing durability of internal coating silicon fume concrete with different external coatings, fast freeze-thaw (FT) cycle testing was performed for three types of external coatings applied to the internal coatings of silicon fume concrete. Using ultrasonic testing and compressive strength tests, we analysed the relationships between the ultrasonic pulse velocity and the mechanical and physical properties of concrete under freeze-thaw action. The results show that the compressive strength and pulse velocity of the studied concrete changed little before the first 100 FT cycles but varied significantly after being subjected to 100 FT cycles and diminished linearly with increasing FT cycles. The dynamic elastic parameters of the concrete were inferred using pulse velocity calculations, and the dependence on FT cycles was very similar to that of ultrasonic pulse velocity. The concrete strength was strongly and positively correlated with ultrasonic pulse velocity. The linear regression model of between ultrasonic pulse velocity, kinetic coefficient, and compressive strength of concrete was also established. The damage incurred to the external coating material (XT-HPA + XT-SS and XT-HPS) was small, and the good performance of the concrete with the added inorganic coating after freeze-thaw cycles indicates good frost resistance.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

Estimating the Concrete Compressive Strength by Using the Concrete Ultrasonic Pulse Velocity and Moduli of Elasticity

2021 ◽  
Vol 1164 ◽  
pp. 77-86
Author(s):  
Bogdan Bolborea ◽  
Sorin Dan ◽  
Claudiu Matei ◽  
Aurelian Gruin ◽  
Cornelia Baeră ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Testing ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
High Rate ◽  
Concrete Compressive Strength ◽  
Destructive Testing ◽  
Non Destructive ◽  
Moduli Of Elasticity

Developing a non-destructive method which delivers fast, accurate and non-invasive results regarding the concrete compressive strength, is an important issue, currently investigated by many researchers all over the world. Different methodologies, like using the simple non-destructive testing (NDT) or the fusion of different techniques approach, were taken into consideration in order to find the optimal, most suitable method. The purpose of this paper is to present a new approach in this direction. The methodology consists in predicting the concrete compressive strength through ultrasonic testing, for non-destructive determination of the dynamic and static moduli of elasticity. One important, basic assumption of the proposed methodology considers values provided by technical literature for concrete dynamic Poisson’s coefficient. The air-dry density was experimentally determined on concrete cores. The dynamic modulus of elasticity was also experimentally determined by using the ultrasonic pulse velocity (UPV) method on concrete cores. Further on, the static modulus of elasticity and the concrete compressive strength can be mathematically calculated, by using the previously mentioned parameters. The experimental procedures were performed on concrete specimens, namely concrete cores extracted from the raft foundation of a multistorey building; initially they were subjected to the specific NDT, namely ultrasonic testing, and the validation of the results and the proposed methodology derives from the destructive testing of the specimens. The destructive testing is generally recognized as the most trustable method. The precision of the proposed method, established with respect to the destructive testing, revealed a high level of confidence, exceeding 90% (as mean value). It was noticed that even the cores with compressive strength outside of mean range interval (minimum and maximum values) presented high rate of precision, not influencing the overall result. The high rate of accuracy makes this method a suitable research background for further investigations, in order to establish a reliable NDT methodology which could substitute the very invasive and less convenient, destructive method.

Assessment of Compressive Strength for RC Building Using the Non-Destructive Test and the SonReb Method: A Case Study

2021 ◽  
Vol 1021 ◽  
pp. 45-54
Author(s):  
Mohammed Al-Helfi ◽  
Ali Allami
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Method ◽  
Technical Institute ◽  
Existing Building ◽  
Destructive Test ◽  
Non Destructive

Non-Destructive methods have greater advantage in assessing the homogeneity, compressive strength, corrosion of rebars in concrete etc. of damaged structures. The aim of the present study is to assess the existing building, which is 41 year old, in the Technical Institute of Amara affiliated with the Southern Technical University, Maysan, Iraq. The research focus on the assessment of the concrete strength and the inspection of the damages in the building. Besides the visual inspection, the ultrasonic pulse velocity and schmidt hammer were used as a non-destructive test method for testing of 30 columns and 15 beams for a building consisting of three floors. The concrete compressive strength was estimated by using SonReb method. The equations proposed by Gasparik, 1984, Di Leo & Pascale, 1994, Arioglu et al., 1996, Cristofaro et al. (EXP), 2020 and Cristofaro et al (PW), 2020 were used for assessment the compressive strength of oncrete. The non-destructive test results indicated that the average strength of the structural elements greater than the design compressive strength of the tested elements. Therefore, the building can be considered structurally is safe.

THE EFFECT OF AGE ON THE COMPRESSIVE STRENGTH OF CONCRETE BY USING ULTRASONIC PULSE VELOCITY

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Qadri Ahmed Yousif ◽  
Idris Bedirhanoglu ◽  
Mehmet Enver Aydin ◽  
Ziwar Zebari
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Strength Development ◽  
The One ◽  
Non Destructive ◽  
Effect Of Age ◽  
Ready Mix Concrete

In this study, the effect of age on the strength development of concrete was investigated. For this purpose, specimens casted with ready mix concrete for different grades of concrete were obtained from ready-mix concrete firms available in Diyarbakir city which is the one of the biggest cities of Turkey. A few sets with different grade of concrete cube specimens were used in the experimental work. Each set included over 40 specimens. For measuring concrete strength development, two different tests were used: ultrasonic pulse velocity testing (UPV) and uniaxial compressive strength testing. After UPV and compressive strength tests, strength development for early ages was evaluated and defined. The aim of this work is to define the path of strength development of certain grades of concrete used in the east regions of Turkey. Another aim of the work is to be able to determine concrete strength through non-destructive UPV tests. As a result, it was seen that concrete strength development for early ages is not linearly proportional to age. Further, UPV measurements can give information on the progress of concrete strength.

scholarly journals Using Ultrasonic Pulse Velocity Test to Assess the Effect of Water-Cement Ratio on the Compressive Strength of Concrete

2019 ◽  
Vol 25 (5) ◽  
pp. 79-86 ◽  
Author(s):  
Ziwar Zebari
Keyword(s):  
Compressive Strength ◽  
Material Science ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Effect Of Water ◽  
Strength Tests ◽  
Compressive Strength Of Concrete

This study aims to find the effect of water-cement ratio on the compressive strength of concrete by using ultrasonic pulse velocity test (UPVT). Over 230 standard cube specimens were used in this study, with dimensions of 150mm, and concrete cubes were cured in water at 20 °C. Also, the specimens used in the study were made of concrete with varied water-cement ratio contents from 0.48 to 0.59. The specimens were taken from Diyarbakir-Turkey concrete centers and tested at the structure and material science lab, civil engineering, faculty of engineering from Dicle University.  The UPV measurement and compressive strength tests were carried out at the concrete age of 28 days. Their UPV and compressive strength ranged between (3.89-4.66km/s) and (17.74-40.56MPa) respectively. The experimental results showed that although the UPV and the compressive strength of concrete are related, also, the UPV and compressive strength have a relation with the rate of the water-cement ratio of concrete.  

scholarly journals Assessment of Strength Development at Hardened Stage on High-Strength Concrete Using NDT

2020 ◽  
Vol 10 (18) ◽  
pp. 6261
Author(s):  
Taegyu Lee ◽  
Jaehyun Lee ◽  
Hyeonggil Choi
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Temperature History ◽  
Strength Development ◽  
Strength Concrete

This study proposes model formulae for predicting the strength of concrete by analyzing the relationships between the results of nondestructive testing (NDT) methods and the compressive strength of concrete specimens at the hardened stage. Further, NDT of concrete molds and mock-up specimens was conducted using NDT methods (rebound hammer, ultrasonic pulse velocity). The water/cement (W/C) ratios were set to 0.48, 0.41, and 0.33 to achieve concrete strengths within the compressive strength range of 24–60 MPa. The evaluation parameters included the fresh concrete properties, compressive strength (mold and core), temperature history, maturity, rebound value, and ultrasonic pulse velocity. Evaluation results indicated that the reliability of existing models, based on the rebound and ultrasonic pulse velocity, is significantly low on high-strength concrete of 40 MPa or higher, and cannot satisfy the ±20% error range. Consequently, this study proposes a regression equation of the concrete strength based on the experimental rebound and ultrasonic pulse velocity values in a 24–60 MPa range, which offers satisfactory reliability.

scholarly journals Performance of Mortars with Commercially-Available Reactive Magnesium Oxide as Alternative Binder

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 938 ◽  
Author(s):  
Miguel Bravo ◽  
Javier A. Forero ◽  
José Nobre ◽  
Jorge de Brito ◽  
Luís Evangelista
Keyword(s):  
Compressive Strength ◽  
Dynamic Modulus ◽  
Mechanical Performance ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
The Other ◽  
Strength Tests ◽  
Durability Performance ◽  
Different Levels

This paper intends to analyze the performance of mortars with reactive MgO, as a sustainable alternative to cement. Six different MgOs from Australia, Canada, and Spain were used in the production of mortars as partial substitutes for cement, namely 5%, 10%, 15%, 20%, and 25% (by weight). MgOs with different levels of reactivity were used to analyze its influence on the performance of MgO mortars. In order to evaluate the mechanical performance of these mortars, compressive strength, flexural strength, dynamic modulus of elasticity, and ultrasonic pulse velocity tests were performed. Compressive strength tests showed that the use of 25% reactive MgO can cause a decrease of this property of between 28% and 49%. The use of reactive MgO affected the other mechanical properties less. This paper also intends to analyze the durability performance of mortars with reactive MgO. To that effect, water absorption by capillarity was assessed. In this research, the effect of using MgO on the shrinkage was also analyzed. It was found that shrinkage may decrease by more than a half in some cases.

scholarly journals The Hydration, Mechanical, Autogenous Shrinkage, Durability, and Sustainability Properties of Cement–Limestone–Slag Ternary Composites

2021 ◽  
Vol 13 (4) ◽  
pp. 1881
Author(s):  
Mei-Yu Xuan ◽  
Yi Han ◽  
Xiao-Yong Wang
Keyword(s):  
Compressive Strength ◽  
Electrical Resistivity ◽  
Experimental Studies ◽  
Autogenous Shrinkage ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hydration Heat ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio

This study examines the hydration–mechanical–autogenous shrinkage–durability–sustainability properties of ternary composites with limestone filler (LF) and ground-granulated blast furnace slag (BFS). Four mixtures were prepared with a water/binder ratio of 0.3 and different replacement ratios varying from 0 to 45%. Multiple experimental studies were performed at various ages. The experimental results are summarized as follows: (1) As the replacement levels increased, compressive strength and autogenous shrinkage (AS) decreased, and this relationship was linear. (2) As the replacement levels increased, cumulative hydration heat decreased. At the age of 3 and 7 days, there was a linear relationship between compressive strength and cumulative hydration heat. (3) Out of all mixtures, the ultrasonic pulse velocity (UPV) and electrical resistivity exhibited a rapid increase in the early stages and tended to slow down in the latter stages. There was a crossover of UPV among various specimens. In the later stages, the electrical resistivity of ternary composite specimens was higher than plain specimens. (4) X-ray diffraction (XRD) results showed that LF and BFS have a synergistic effect. (5) With increasing replacement ratios, the CO2 emissions per unit strength reduced, indicating the sustainability of ternary composites.

Sign in / Sign up

Export Citation Format

Share Document