scholarly journals Study on Lateral Deformation and Failure Characteristics of Coal Based on Different Confining Pressures

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Jian-jun Ren ◽  
Shan-Yang Wei ◽  
Shi-Hai Shu ◽  
Wei-Dong Luo
Keyword(s):  
Axial Strain ◽  
Peak Stress ◽  
Confining Pressure ◽  
Lateral Strain ◽  
Lateral Deformation ◽  
Axis Ratio ◽  
Deformation And Failure ◽  
Initial Stage ◽  
Confining Pressures ◽  
Potential Parameters

To study the lateral deformation characteristics of coal under different confining pressures, coal compression experiments with confining pressures of 0 MPa, 3 MPa, 5 MPa, and 7 MPa were conducted under the same loading rate by using the TAW-2000 electrohydraulic servo rock mechanics experimental machine. The results of the study showed the following: at the initial stage of loading, the lateral strain of coal was about 12.22%–46.9% of the axial strain at the elastic deformation stage and 41.18%–64.96% of the axial strain at the inelastic deformation to peak stress stage. Compared with the experiment under 0 MPa confining pressure, the growth rate of the lateral strain of the coal under 3 MPa, 5 MPa, and 7 MPa confining pressures was much smaller than that of the corresponding axial strain. When the coal was damaged under different confining pressures, the lateral strain was maintained at about 0.6 × 10−2. Based on the field verification, we proposed that the lateral strain during the coal failure and the nonlinear region of the lateral axis ratio changing with time can be used as potential parameters for predicting the coal failure.

Strength Attenuation and Post Failure Behaviour of Fine Sandstone

2012 ◽  
Vol 446-449 ◽  
pp. 3538-3543
Author(s):  
Ji Jun Zhou ◽  
Huai Fu ◽  
Yue Zhang ◽  
Yan Li ◽  
De Zhang
Keyword(s):  
Shear Test ◽  
Fractured Rock ◽  
Axial Strain ◽  
Confining Pressure ◽  
Lateral Strain ◽  
Material Strength ◽  
Failure Behaviour ◽  
Block Shear ◽  
Stress Peak ◽  
Confining Pressures

Three types of physical tests were designed to study post failure behaviour and strength attenuation of fine sandstone. Tests include rock compression test, rock unloading test and rock block shear test. The stress-strain curves at different confining pressures had been obtained as well as axial strain-lateral strain curves. The differences of axial strain-lateral strain curves exhibit that stress peak point and the point of fault formation are apparently different for the rock. After the fault is generated, fractured rock slides on the fault surfaces, while confining pressure, material strength and structure effect decide the post failure behaviour. Damaged rock specimens were poured in concrete specimens as well as irregular blocks. Material strength of rock blocks was attained. Shear strength gradually attenuates with unloading points close to the peak. Past the stress peak, rock blocks from fractured rock still have considerable material strength. It is shown that there are differences of strength parameters obtained from direct shear test and triaxial test.

scholarly journals Deformation and Acoustic Emission Characteristics of Cracked Granite during Creep

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Chunping Wang ◽  
Jingli Xie ◽  
Jian Liu
Keyword(s):  
Acoustic Emission ◽  
Axial Strain ◽  
Failure Process ◽  
Deformation Characteristic ◽  
Temporal Distribution ◽  
Confining Pressure ◽  
High Energy ◽  
Lateral Strain ◽  
Creep Tests ◽  
Confining Pressures

A series of multistage creep tests under different confining pressures with acoustic emission monitoring have been performed to investigate the deformation characteristic and failure process of cracked granite during creep. The critical axial strain of cracked sample showed an increasing tendency with the increase of confining pressure. In contrast, critical lateral strain experienced a process of descending first at low confinement and then remaining nearly constant at high confinement. Compared with loading-cracked specimen, smaller critical axial strain, greater critical lateral strain, and higher lateral creep strain rate were found for unloading-cracked specimen. Based on the spatial and temporal distribution of acoustic emission events, the cracking process during creep was analysed. The AE events with high energy are mainly concentrated at the final fracture area of the specimen. The higher the confining pressure, the more the AE events with low energy. Compared with the loading-cracked specimen, the percentage of AE events with high energy is relatively small for the unloading-cracked specimen.

scholarly journals Research on Microscopic Evolution Laws of Sandstone Deformation and Failure Based on the Particle Discrete Element Method

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhiwei Cai ◽  
Tongqing Wu ◽  
Jian Lu ◽  
Yue Wu ◽  
Nianchun Xu
Keyword(s):  
Shear Crack ◽  
Rock Fracture ◽  
Confining Pressure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Deformation And Failure ◽  
Fracture Development ◽  
Confining Pressures ◽  
The Law ◽  
Microcrack Growth

The fracture of sandstone is closely related to the condition of internal microcracks and the fabric of micrograin. The macroscopic mechanical property depends on its microscopic structures. However, it is difficult to obtain the law of the microcrack growth under loading by experiments. A series of microscopic sandstone models were established with particle flow code 3D (PFC3D) and based on the triaxial experiment results on sandstones. The experimental and numerical simulations of natural and saturated sandstones under different confining pressures were implemented. We analyzed the evolution of rock deformation and the rock fracture development from a microscopic view. Results show that although the sandstones are under different confining pressures, the law of microcrack growth is the same. That is, the number of the microcracks increases slowly in the initial stage and then increases exponentially. The number of shear cracks is more than the tensile cracks, and the proportion of the shear cracks increases with the increase of confining pressure. The cracking strength of natural and saturated sandstones is 26% and 27% of the peak strength, respectively. Under low confining pressure, the total number of cracks in the saturated sample is 20% more than that of the natural sample and the strongly scattered chain is barely seen. With the increase of the confining pressure, the effect of water on the total number of cracks is reduced and the distribution of the strong chain is even more uniform. In other words, it is the confining pressure that mainly affects the distribution of the force chain, irrespective of the state of the rock, natural or saturated. The research results reveal that the control mechanism of shear crack friction under the different stress states of a rock slope in the reservoir area provides a basis for evaluating the stability of rock mass and predicting the occurrence of geological disasters.

Comparison of Stress-Strain Relationships of FRP and Actively Confined High-Strength Concrete: Experimental Observations

2014 ◽  
Vol 919-921 ◽  
pp. 29-34 ◽  
Author(s):  
Jian Chin Lim ◽  
Togay Ozbakkloglu
Keyword(s):  
High Strength Concrete ◽  
Axial Stress ◽  
Axial Strain ◽  
High Strength ◽  
Confining Pressure ◽  
Confined Concrete ◽  
Lateral Strain ◽  
Stress Strain ◽  
Strength Concrete ◽  
Actively Confined Concrete

It is well established that lateral confinement of concrete enhances its axial strength and deformability. It is often assumed that, at a same level of confining pressure, the axial compressive stress and strain of fiber reinforced polymer (FRP)-confined concrete at a given lateral strain are the same as those in concrete actively confined concrete. To assess the validity of this assumption, an experimental program relating both types of confinement systems was conducted. 25 FRP-confined and actively confined high-strength concrete (HSC) specimens cast from a same batch of concrete were tested under axial compression. The axial stress-strain and lateral strain-axial strain curves obtained from the two different confinement systems were assessed. The results indicate that, at a given axial strain, lateral strains of actively confined and FRP-confined concretes correspond, when they are subjected to the same lateral confining pressure. However, it is observed that, at these points of intersections on axial strain-lateral strain curves, FRP-confined concrete exhibits a lower axial stress than the actively confined concrete, indicating that the aforementioned assumption is not accurate. The test results indicate that the difference in the axial stresses of FRP-confined and actively confined HSC becomes more significant with an increase in the level of confining pressure.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

Experimental Design about Degradation Mechanism of CAM and Preliminary Experiment Results

2013 ◽  
Vol 663 ◽  
pp. 703-707
Author(s):  
Jian Zeng Li ◽  
Jin Feng Wang ◽  
Jian Ping Lin
Keyword(s):  
Mechanical Property ◽  
High Speed ◽  
Degradation Mechanism ◽  
Fatigue Property ◽  
Peak Stress ◽  
Confining Pressure ◽  
Degradation Model ◽  
Increase With Increase ◽  
Cement Asphalt Mortar ◽  
Confining Pressures

Cement Asphalt Mortar (CAM) layer is the key to the structure of slab track in the high-speed railways. In the running of high-speed railways, the CAM layer must bear the action of temperature change, initial defects and trains loading, it will lead to the degradation of CAM. This paper designed the experiments to study its mechanical property under confining pressure or water erosion, tensile property, fatigue property, interface stress of CAM and concrete roadbed; it will help us to establish the failure criterion and degradation model of CAM layer. Preliminary experiment chose three confining pressures to study the mechanical property of CAM; the results indicate that peak stress and ductility of CAM greatly increase with increase of confining pressure.

scholarly journals Experimental Study on Mechanical Properties of Deep Buried Granite under Different Confining Pressures

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Jun Zhao ◽  
Tan Zhang
Keyword(s):  
Cyclic Loading ◽  
Confining Pressure ◽  
Surrounding Rock ◽  
Underground Engineering ◽  
Failure Characteristics ◽  
Deformation And Failure ◽  
Cyclic Loading And Unloading ◽  
Confining Pressures ◽  
Crack Damage Stress ◽  
Loading And Unloading

Brittle failure of hard rock poses a serious threat to the stability of surrounding rock in deep underground engineering. In order to study the deformation and failure characteristics of deep buried granite under high confining pressure cyclic loading and unloading, MTS815 electro-hydraulic servo rock test system was used to conduct cyclic loading and unloading tests under confining pressures of 15 MPa, 35 MPa, 45 MPa, and 55 MPa, and the corresponding stress-strain curves and deformation failure characteristic curves were obtained. The experimental results show the follows: (1) under the same confining pressure, the peak strength, crack initiation stress, crack damage stress, and Poisson’s ratio of the specimens under cyclic loading and unloading are larger than those under conventional triaxial loading and unloading, and the unloading elastic modulus is smaller than that, under conventional triaxial compression; (2) the results show that, under different confining pressures, the granite samples show obvious brittle failure characteristics, the elastic modulus and crack initiation stress increase first and then decrease with the confining pressure, the peak strength and crack damage stress of the samples increase linearly with the confining pressure, and Poisson’s ratio increases first and then remains unchanged with the confining pressure; (3) under the two kinds of stress conditions, the macroscopic failure of the samples is mainly shear failure. The deformation and failure law of granite samples revealed in this study has significant reference value for the selection of rock mass mechanical model of surrounding rock stability of underground engineering, the formulation of surrounding rock support countermeasures, and the evolution law of mechanical parameters with damage variables.

scholarly journals Experimental Research into the Evolution of Permeability of Sandstone under Triaxial Compression

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5065
Author(s):  
Liming Zhang ◽  
Shengqun Jiang ◽  
Jin Yu
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Testing Machine ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Rate Of Change ◽  
Peak Strength ◽  
Sudden Increase ◽  
Seepage Pressure ◽  
Confining Pressures

Failure tests on sandstone specimens were conducted under different confining pressures and seepage pressures by using an MTS triaxial rock testing machine to elucidate the corresponding correlations of permeability and characteristic stress with confining pressure and pore pressure during deformation. The results indicate that permeability first decreases and presents two trends, i.e., a V-shaped increase and an S-shaped trend during the non-linear deformation stage. The greater the seepage pressure, the greater the initial permeability and the more obvious the V-shaped trend in the permeability. As the confining pressure was increased, the trend in the permeability gradually changed from V- to S-shaped. Compared with the case at a high confining pressure, the decrease of permeability occurred more quickly, the rate of change becomes greater, and the sudden increase observed in the permeability happened earlier under lower confining pressures. Within the range tested, confining pressure exerted a greater effect on the permeability than the seepage pressure. In comparison with the axial strain, volumetric strain better reflected changes in permeability during compaction and dilation of sandstone. The ratio of crack initiation stress to peak strength ranged from 0.37 to 0.50, while the ratio of dilation stress to peak strength changed from 0.58 to 0.72. Permeabilities calculated based on Darcy and non-Darcy flow changed within the same interval, while the change in permeability was different.

scholarly journals Sealing Performance of New Solidified Materials: Mechanical Properties and Stress Sensitivity Characterization of Pores

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Chao Zhang ◽  
Gaohan Jin ◽  
Chao Liu ◽  
Shugang Li ◽  
Junhua Xue ◽  
...  
Keyword(s):  
Coal Sample ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Peak Stress ◽  
Confining Pressure ◽  
Stress Sensitivity ◽  
Test System ◽  
Sample Material ◽  
Sealing Material ◽  
The Difference

Borehole-sealing solidified material plays a significant role in improving sealing quality and enhancing gas drainage performance. In this study, the MTS815 electro-hydraulic triaxial servo test system and MR-60 NMR test system were adopted to conduct triaxial compression control experiment on the coal sample material, concrete material, and new solidified sealing material, respectively. This paper aims to analyze the difference of support effects, porosity, and stress sensitivity between those materials. Experimental results show that under the same stress condition, the stiffness of traditional concrete solidified material is the largest, while the new solidified material is the second, and the coal sample material is the smallest. Compared with the traditional concrete solidified material, the new solidified sealing material has better strain-bearing capacity and volumetric expansion capacity under each confining pressure in the experiment. The axial strain and volume increment of new solidified material is higher than those of the traditional concrete solidified material at the peak stress. Meanwhile, the confining pressure has a certain hysteresis effect on the postpeak stress attenuation. Fracture has the strongest stress sensitivity in three pore types, and its T2 map relaxation area has a larger compression than adsorption pore and seepage pore under the same pressure. The relative content of seepage pore and fracture in the new solidified material is less than that of coal and concrete samples, and the stress sensitivity of the new solidified materials is weaker than that of coal and concrete materials, thence, new solidified material will have better performance in borehole sealing. Outcomes of this study could provide guidance on the selection of the most effective sealing materials for sealing-quality improvement.

scholarly journals Experimental Study on Viscoplastic Property of Unsaturated Reticulate Red Clay Used as an Engineered Barrier

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Chuang Zhang ◽  
Jian-Zhong Li ◽  
Yong He
Keyword(s):  
Axial Strain ◽  
Confining Pressure ◽  
Matric Suction ◽  
Triaxial Tests ◽  
Red Clay ◽  
Reticulate Red Clay ◽  
Confining Pressures ◽  
Loading Tests ◽  
Engineered Barrier ◽  
The Relationship

In this study, to explore the feasibility of a compacted red clay as an engineered barrier in landfills, the viscoplastic property of remodeled unsaturated reticulate red clay was studied through a series of triaxial tests. According to the deviatoric stress–axial strain curves obtained through loading tests with varying strain rates and under different conditions, the viscoplastic parameter β of remodeled reticulate red clay was obtained. The effects of different matric suctions and net confining pressures on the viscoplasticity of unsaturated reticulate clay were analyzed. The test results showed that remodeled reticulate red clays with different degrees of saturation have similar viscoplastic properties, and their stress–strain curves are all isotach. The stiffness of unsaturated reticulate red clay increased with increasing confining pressure and matric suction. The relationship between β and the net confining pressure can be described using a linear equation. The β value of the specimens increased with increasing matric suction under a constant net confining pressure. A similar linear relationship was observed between β and the matric suction. These relationships are explained considering the loading rate effect mechanism.

Sign in / Sign up

Export Citation Format

Share Document