scholarly journals Investigation of Flexural Capacity of Concrete Containing Liquid Silicone Rubber

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Alireza Khaloo ◽  
Yaser Parvin Darabad
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Silicone Rubber ◽  
Aggregate Size ◽  
Splitting Tensile Strength ◽  
Hardened Concrete ◽  
Fine Aggregate ◽  
Liquid Form ◽  
Liquid Silicone ◽  
Concrete Recycling

Despite the great use of concrete, tensile strength and low flexibility and brittleness are its weaknesses. Many solutions have been provided to eliminate the mentioned defects. In order to increase the flexibility of concrete in previous studies, crushed rubber tire particles have been added to concrete. Recycling car tires helps the environment and makes concrete much more flexible than regular concrete. In this research, silicone rubber has been replaced by 0%, 2%, 4%, 8%, 12.5%, 25%, and 50% of mineral aggregates. This rubber was initially in liquid form, which, after mixing with ordinary concrete, dispersed into the concrete texture and formed a uniform mixture, and this liquid rubber became a flexible solid after 24 hours. Concrete containing silicone rubber is a new composite with new properties, and in this research, it is called Hybrid Silicone Rubber Concrete (HSRC). Also, to evaluate the effect of aggregate size in making experimental specimens, two coarse to fine aggregate ratios of G/S = 0.7, 1.1 were considered. Flexural strength tests were performed on hardened concrete beam specimens. The results showed that, with increasing the amount of silicone rubber in concrete, flexural strength decreased and this percentage of strength reduction was compared with the percentage of reduction in compression and splitting tensile strength. It was found that the reduction of flexural strength was less than compression and splitting tensile strength. Larger deformation was observed during all tests when the concentration of silicone rubber increased. It was observed that the higher the amount of silicone rubber in the specimens, the less noise and the less separation of aggregates with which the failure of the specimens was associated.

Performance of Iron Ore Tailings as Partial Replacement for Sand in Concrete

2015 ◽  
Vol 735 ◽  
pp. 122-127 ◽  
Author(s):  
Sikiru Oritola ◽  
Abd Latif Saleh ◽  
Abdul Rahman Mohd Sam
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Iron Ore ◽  
Splitting Tensile Strength ◽  
Concrete Sample ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Fine Aggregate ◽  
Iron Ore Tailings

This paper reports preliminary findings on the properties of concrete produced using iron ore tailings obtained from ZCM Minerals SDN BHD located in Kotta Tingi, Johor, Malaysia. The Iron Ore Tailings (IOT’s) a waste product, with particle size range from (850μm - 75μm) obtained from Iron Ore Processing was utilized as fine aggregate to produce concrete. Based on British Standard (BS) guidelines, normal concrete mix was designed. Five types of concrete samples (C0, C1, C2, C3, and C4) were produced, with the percentage of tailings used to replace sand as fine aggregate ranging from 0 to 40[%]. The reference sample is C0 with no tailings and the four others, containing tailings at 10[%] intervals. The effect of iron ore tailings on the consistency of the fresh concrete were studied, as well as the density, compressive strength, flexural strength and splitting tensile strength, of the hardened concrete. The results of the consistency tests on concrete shows that the slump values ranges from 81 to 53[mm] from concrete sample C0 to C4 respectively, while the compacting factor values ranges from 0.92 to 0.89 respectively. The density of the produced concrete cube samples falls within the range 2350 to 2430[kg/m3]. The concrete sample C3 gave the highest compressive strength value of 43.70[N/mm2]. The concrete sample C3 also gave the highest flexural strength value of 4.79[N/mm2], while the The concrete sample C4 gave the highest splitting tensile strength value of 4.0[N/mm2] after curing period of 28[days].

scholarly journals Research on the Effect of Cooper Slag as a Fine Aggregate on the Properties of Concrete

2019 ◽  
Vol 8 (2S3) ◽  
pp. 619-623
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Copper Slag ◽  
Splitting Tensile Strength ◽  
Copper Recovery ◽  
Concrete Mixture ◽  
Copper Smelting ◽  
Fine Aggregate

Copper slag is a rough blasting grit or a by-product acquired by the process of copper smelting and refining. These copper slags are recycled for copper recovery. In this paper, we analysed copper slag’s feasibility and evaluate its total competence in M25 grade concrete. In this observation, a concrete mixture is applied with copper slag as a fine aggregate ranging from 0%, 20%, 40%, 60%, 80%, and 100% respectively. The strength of copper slag’s implementation is accomplished on the basis of concrete’s flexural strength, compressive strength and splitting tensile strength. From the obtained results, in concrete 40% percentage of copper slag is used as sand replacement. On 28 days, the modulus of elasticity increased up to 32%, the compressive strength increased up to 34% and flexural strength is increased to 6.2%. From this experiment, it is proved technically that replacing sand using copper slag as a fine mixture in M25 grade concrete.

scholarly journals Study on the Effect of Nano-Silica in Mechanical and Durability Properties of Concrete with Steel Fiber

2022 ◽  
pp. 50-55
Author(s):  
Vasanth G ◽  
Dr. K. Ramadevi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Hardened Concrete ◽  
Nano Silica ◽  
Partial Cement Replacement ◽  
Volume Substitution

This study presents experimentally the combined effect of using Nano-silica (NS) and steel fibers (SF) on the mechanical properties of hardened concrete. NS is used as partial cement replacement by different percentages, and SF is used as volume substitution by different percentages. Splitting tensile strength, modulus of elasticity, and flexural strength are evaluated using different combinations between NS and SF. Significant improvement in the mechanical properties of concrete is observed on using NS due to its high pozzolanic activity. The Optimum content of SF is improved splitting tensile strength with different percentages respectively compared to without either NS or SF. Utilizing NS with SF leads to improving modulus of elasticity compared to without either NS or SF. Flexural strength is doubled for using NS and SF compared to without NS and SF.

scholarly journals Influence of Percentage Replacement of Metakaolin on Different Concrete Types Exposed to Internal Sulphate Attack

2018 ◽  
Vol 7 (4.20) ◽  
pp. 514
Author(s):  
Hadeel K. Awad ◽  
Rawaa K. Aboud ◽  
Shatha D. Mohammed
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Splitting Tensile Strength ◽  
Fine Aggregate ◽  
Sulphate Attack ◽  
Concrete Properties ◽  
Reactive Powder ◽  
Positive Effect

This research presents an experimental investigation on the influence of metakaolin replacement percentage upon some properties of       different concrete types. Three types of concrete were adopted (self- compacted concrete, high performance concrete and reactive powder concrete) all of high sulphate (SO3) percentage from the fine aggregate weight, 0.75%.Three percentages of metakaolin replacement were selected to be studied (5, 7 and 10) %. Three types of concrete properties (compressive, flexural and splitting tensile strength) were adopted to achieve better understanding for the influence of adding metakaolin.. The output results indicated that the percentage of metakaolin had a different level of positive effect on the compressive strength for both including and excluding of internal sulphate attack. This effect reached at 28 days of curing to (11.86, 10.22 and 4.75) % in case of excluding sulphate attack and to (13.82, 11.47and 6.53) % in the other case for SCC, HPC and RPC respectively. It can be concluded that the effect of metakaolin in both SCC and HPC are more influence than in RPC. Splitting and flexural strength have showed a similar behavior, flexural strength increased by (15.38, 9.42 and 5,84) % at age of 28 days when the sulphate attack is excluded, while it was (14.02, 10.66 and 4.28)% in case of sulphate attack included for SCC,HPC and RPC respectively. The response of splitting tensile strength for both including and excluding of sulphate attack reached to (13.03, 12.95 and 9.17) % and (16.88, 10.33 and 6.74) % respectively for SCC, HPC and RPC.   

scholarly journals An Investigation on Adding Polypropylene Fibers to Reinforce Lightweight Cement Composites (LWC)

2012 ◽  
Vol 7 (4) ◽  
pp. 155892501200700 ◽  
Author(s):  
Roohollah Bagherzadeh ◽  
Hamid Reza Pakravan ◽  
Abdol-Hossein Sadeghi ◽  
Masoud Latifi ◽  
Ali Akbar Merati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Fiber Length ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Splitting Tensile Strength ◽  
Hardened Concrete ◽  
Polypropylene Fibers ◽  
Cement Composites

The influence of polypropylene fibers has been studied in different proportioning and fiber length to improve the performance characteristics of the lightweight cement composites. Fibers used in two different lengths (6mm and 12mm) and fiber proportions (0.15% and 0.35%) by cement weight in the mixture design. Hardened concrete properties such as: 7- and 28-day compressive strength, splitting tensile strength, flexural strength, water absorption, and shrinkage were evaluated. Fiber addition was seen to enhance the physical and mechanical properties of lightweight concrete. Compared to unreinforced LWC, polypropylene (PP) reinforced LWC with fiber proportioning 0.35% and 12 mm fiber length, caused 30.1% increase in the flexural strength and 27% increase in the splitting tensile strength. Increased fiber availability in the LWC matrix, in addition to the ability of longer PP fibers to bridge on the micro cracks, are suggested as the reasons for the enhancement in mechanical properties.

scholarly journals Study on Properties of Concrete with Iron Ore Tailing and Glass Waste

2021 ◽  
Vol 8 (1) ◽  
pp. 30-39
Author(s):  
KS Sushmitha ◽  
P Dhanabal
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
Iron Ore ◽  
Glass Powder ◽  
Splitting Tensile Strength ◽  
Fine Aggregate ◽  
Content Increase ◽  
Waste Products ◽  
Iron Ore Tailings

The aim of this research is to test the characteristics of concrete by substitute fine aggregate with iron ore tailings and partial glass powder as in the place of cement. Concrete with waste products such as glass powder and iron ore tailings offer technical, economic and environmental advantages. In this experimental investigation, glass powder is replaced with cement by 10%, 20% and 30% and iron ore tailings with fine aggregates by 30% which is the optimum percentage. To study the role of glass powder and iron ore tailings combination in concrete. The properties such compressive strength, flexural strength, tensile strength and also durability parameters likely water absorption investigation for M40 concrete is carried out with different percentages of glass powder by keeping the iron ore tailings percentage constant. At 30% glass powder substitution as cement and sand with IOT increases concrete effectiveness. The concrete with 10% glass powder & 30% iron ore tailings showed a higher strength compared to the conventional mix for 28 days. Concrete mix containing 10% GP and 30% IOT showed higher flexural strength of 5.05 MPa for 28 days. Splitting tensile strength value is also increasing i. e for 10% glass powder and 30% IOT, obtained splitting tensile strength was 4.48 MPa and modulus of elasticity value was has also increased. Water absorption experiment consequences results that water absorption decreases with an increase in GP percentage.  The concrete workability tends to decrease when with glass powder content increase. Concrete containing 10% glass powder and 30% IOT showed maximum strength and it is considered as the optimum dosage.

Effect of using magnetic water on the mechanical properties of concrete exposed to elevated temperature

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wasim Barham ◽  
Ammar AL-Maabreh ◽  
Omar Latayfeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Tap Water ◽  
Splitting Tensile Strength ◽  
Content Type ◽  
Normal Water ◽  
Magnetic Water

PurposeThe influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.Design/methodology/approachExperimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.FindingsExposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.Originality/valuePrevious research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

scholarly journals Enhancing the Flexural Strength of Concrete using Recycled Iron and Steel Slag Aggregate

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
A. A Raheem
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Concrete Beams ◽  
Steel Slag ◽  
Aggregate Size ◽  
Mineralogical Composition ◽  
Maximum Aggregate Size ◽  
Considerable Effort ◽  
Iron And Steel ◽  
Coefficient Of Uniformity

Concrete is strong in compression but weak in tension hence, considerable effort is required to improve concrete’s tensile strength by the use of pre-stressed concrete and addition of admixtures or additives. In this study, the use of recycled iron and steel slag (RISS) aggregate to improve the tensile strength of concrete was considered. The paper assessed the mineralogical composition of RISS and granite aggregates, and gradation. It also determines the effects of RISS aggregate on the flexural strength of concrete beams of 150 × 150 × 600 mm containing 0, 10, 20, 40 and 60% RISS aggregate replacement in mix ratios 1:1½:3, 1:2:4 and 1:3:6 with water cement ratios 0.65,0.60 and 0.55 respectively. Diffractograph of RISS and granite aggregate showed that RISS contains Magnetite, Ilmenite and Quartz, while granite contains Quartz, Annite, Microcline and Albite as the predominant minerals. The coefficient of uniformity and concavity of RISS and granite aggregate for maximum aggregate size of 37.5 mm are 4.35 and 1.33; and 4.64 and 1.76 respectively. Both aggregates contain quartz as the predominant mineral and are well graded. The result of the Flexural strength at 28 days curing is within 0.135 – 0.250 MPa specified byBS8500 – 2:2015. Flexural strength of concrete beams cast with RISS aggregate is relatively higher than concrete cast with granite aggregate. Flexural strength, a measure of tensile strength of concrete is improved as percentage RISS aggregate increased.

scholarly journals Experimental study on the properties of highperformance concrete made with class C fly ash

2019 ◽  
Vol 276 ◽  
pp. 01014
Author(s):  
I Made Alit Karyawan Salain ◽  
I Nyoman Sutarja ◽  
Teguh Arifmawan Sudhiarta
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Permeability Coefficient ◽  
Splitting Tensile Strength ◽  
Type I ◽  
Fine Aggregate ◽  
Hydration Time ◽  
Class C

This experimental study presents the properties of highperformance concrete (HPC) made by partially replacing type I Portland cement (OPC) with class C fly ash (CFA). The purpose of this study is to examine, with hydration time, the development of the compressive strength, the splitting tensile strength and the permeability of HPC utilizing different quantity of CFA. Four HPC mixtures, C1, C2, C3, and C4, were made by utilizing respectively 10%, 20%, 30% and 40% of CFA as replacement of OPC, by weight. One control mixture, C0, was made with 0% CFA. The mix proportion of HPC was 1.00 binder: 1.67 fine aggregate: 2.15 coarse aggregate with water to binder ratio 0.32. In each mixture, it was added 5% silica fume and 0.6% superplasticizer of the weight of the binder. Tests of HPC properties were realized at the age of 1, 3, 7, 28, and 90 days. The results indicate that CFA used to partially replace OPC in HPC shows adequate cementitious and pozzolanic properties. The compressive strength and the splitting tensile strength of HPC increase while the permeability coefficient decreases with increasing hydration time. It is found that the optimum replacement of OPC with CFA is 10%, however the replacement up to 20% is still acceptable to produce HPC having practically similar harden properties with control mixture. At this optimum replacement and after 90 days of hydration, the compressive strength, the splitting tensile strength and the permeability coefficient can reach 68.9 MPa, 8.3 MPa and 4.6 E-11 cm/sec respectively. These results are 109%, 101%, and 48% respectively of those of control mixture.

scholarly journals Developing Geopolymer Concrete Properties by Using Nanomaterials and Steel Fibers

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
E. Rabiaa ◽  
R. A. S. Mohamed ◽  
W. H. Sofi ◽  
Taher A. Tawfik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Sodium Hydroxide ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Geopolymer Concrete ◽  
Alkaline Activator ◽  
The Impact

This research investigates the simultaneous impact of two different types of steel fibers, nanometakaolin, and nanosilica on the mechanical properties of geopolymer concrete (GPC) mixes. To achieve this aim, different geopolymer concrete mixes were prepared. Firstly, with and without nanomaterials (nanosilica and nanometakaolin) of 0, 2%, 4%, 6%, and 8% from ground granulated blast furnace slag (GGBFS) were used. Secondly, steel fiber (hooked end and crimped) content of (0, 0.5%, 1, and 1.5%) was used. Thirdly, optimum values of nanomaterials with the optimum values of steel fiber were used. Crimped and hooked-end steel fibers were utilized with an aspect ratio of 60 and a length of 30 mm. Geopolymer mixes were manufactured by using a constant percentage of alkaline activator to binder proportion equal to 0.45 with GGBFS cured at ambient conditions. For alkaline activator, sodium hydroxide molar (NaOH) and sodium hydroxide solution (NaOH) were used according to a proportion (Na2SiO3/NaOH) of 2.33. The hardened concrete tests were performed through the usage of splitting tensile strength, flexural, and compressive experiments to determine the impact of steel fibers, nanometakaolin, and nanosilica individually and combined on performance of GPC specimens. The results illustrated that using a mix composed of the optimum steel fibers (1% content) accompanied by an optimum percentage of 6% nanometakaolin or 4% nanosilica demonstrated a significant enhancement in the mechanical properties of GPC specimens compared to all other mixtures. Besides, the impact of using nanomaterials individually was found to be predominant on compressive strength on GPC specimens especially with the usage of the optimum values. However, using nanomaterials individually compared to using the steel fibers individually was found to have approximately the same splitting tensile strength and flexural performance.

Sign in / Sign up

Export Citation Format

Share Document