scholarly journals Modeling of Split Ring Resonators loaded microstrip line with different orientations

2015 ◽  
Vol 5 (6) ◽  
pp. 1363
Author(s):  
Rajni Rajni ◽  
Gurwinder Singh ◽  
Anupma Marwaha
Keyword(s):  
Reflection Coefficient ◽  
Microstrip Line ◽  
Ring Resonator ◽  
Magnetic Interaction ◽  
Split Ring Resonator ◽  
Ring Resonators ◽  
Split Ring ◽  
Split Ring Resonators ◽  
High Frequency Structure Simulator ◽  
Equivalent Circuit Parameters

<p>This paper presents the different circuit approaches of the electric and magnetic interaction of Single Split Ring Resonator (SRR) loaded microstrip line. We loaded the microstrip line with planar square split ring resonator in different configurations and orientations. The modeling behavior of metamaterials-based microstrip lines loaded with single and two-mirrored split ring resonators is analyzed numerically in two orientations (with gap of SRR parallel and perpendicular to the line). The full wave simulations are performed for the single and two-mirrored split ring resonators loaded microstrip inside a waveguide with ‘High Frequency Structure Simulator’ software.<strong> </strong>The equivalent circuit parameters are obtained for the single split ring resonator loaded with microstrip line with the gap parallel and near to the line from transmission line theory  that make use of just the resonance frequency and minimum of the reflection coefficient.<strong> </strong>The simulation of different orientations of split ring resonator gives better reflection coefficient and wider frequency.</p>

scholarly journals Coupling Schemes in Terahertz Planar Metamaterials

2012 ◽  
Vol 2012 ◽  
pp. 1-12 ◽  
Author(s):  
Dibakar Roy Chowdhury ◽  
Ranjan Singh ◽  
Antoinette J. Taylor ◽  
Hou-Tong Chen ◽  
Weili Zhang ◽  
...  
Keyword(s):  
Resonance Line ◽  
Ring Resonator ◽  
Near Field ◽  
Split Ring Resonator ◽  
Higher Order ◽  
Ring Resonators ◽  
Split Ring ◽  
Split Ring Resonators ◽  
Sensing Applications ◽  
Lattice Mode

We present a review of the different coupling schemes in a planar array of terahertz metamaterials. The gap-to-gap near-field capacitive coupling between split-ring resonators in a unit cell leads to either blue shift or red shift of the fundamental inductive-capacitive (LC) resonance, depending on the position of the split gap. The inductive coupling is enhanced by decreasing the inter resonator distance resulting in strong blue shifts of theLCresonance. We observe theLCresonance tuning only when the split-ring resonators are in close proximity of each other; otherwise, they appear to be uncoupled. Conversely, the higher-order resonances are sensitive to the smallest change in the inter particle distance or split-ring resonator orientation and undergo tremendous resonance line reshaping giving rise to a sharp subradiant resonance mode which produces hot spots useful for sensing applications. Most of the coupling schemes in a metamaterial are based on a near-field effect, though there also exists a mechanism to couple the resonators through the excitation of lowest-order lattice mode which facilitates the long-range radiative or diffractive coupling in the split-ring resonator plane leading to resonance line narrowing of the fundamental as well as the higher order resonance modes.

scholarly journals Effects of Microstructure Variations on Macroscopic Terahertz Metafilm Properties

2007 ◽  
Vol 2007 ◽  
pp. 1-10 ◽  
Author(s):  
John F. O'Hara ◽  
Evgenya Smirnova ◽  
Abul K. Azad ◽  
Hou-Tong Chen ◽  
Antoinette J. Taylor
Keyword(s):  
Ring Resonator ◽  
Single Layer ◽  
Split Ring Resonator ◽  
Ring Resonators ◽  
Terahertz Frequency ◽  
Structural Components ◽  
Frequency Range ◽  
Terahertz Frequency Range ◽  
Split Ring ◽  
Split Ring Resonators

The properties of planar, single-layer metamaterials, or metafilms, are studied by varying the structural components of the split-ring resonators used to comprise the overall medium. Measurements and simulations reveal how minor design variations in split-ring resonator structures can result in significant changes in the macroscopic properties of the metafilm. A transmission-line/circuit model is also used to clarify some of the behavior and design limitations of the metafilms. Though our results are illustrated in the terahertz frequency range, the work has broader implications, particularly with respect to filtering, modulation, and switching devices.

Coupled ring resonator for microwave characterization of dielectric materials

2012 ◽  
Vol 4 (2) ◽  
pp. 241-246 ◽  
Author(s):  
Mahima Kapoor ◽  
K. S. Daya ◽  
G. S. Tyagi
Keyword(s):  
Dielectric Constant ◽  
Spirulina Platensis ◽  
Ring Resonator ◽  
Dielectric Materials ◽  
Split Ring Resonator ◽  
Ring Resonators ◽  
Split Ring ◽  
Split Ring Resonators ◽  
Closed Ring

In this paper characterization of dielectric materials in liquid and powder phase using concentric closed and split ring resonators of length λ, λ/2, and λ/4 is reported. Experimental results have been validated by simulations and theoretically modeling. Sensitivity of the resonator with closed rings was maximum. Experimentally extracted values of dielectric constant of ferrite ranged from 14.05 to 15.1 with closed ring resonators and from 13.6 to 14.02 with split ring resonator, respectively. For spirulina platensis the dielectric constant was lying in the range 1.78–1.93 and 1.74–2.04 with closed ring and split ring resonators, respectively. The values extracted experimentally are in good agreement with simulation and theoretically found values. However, the values obtained from closed ring resonator were in agreement with the dielectric constant values of ferrite and spirulina platensis.

scholarly journals A Novel SWB Antenna with Triple Band-Notches Based on Elliptical Slot and Rectangular Split Ring Resonators

Electronics ◽  
2019 ◽  
Vol 8 (2) ◽  
pp. 202 ◽  
Author(s):  
Xiaobo Zhang ◽  
Saeed Ur Rahman ◽  
Qunsheng Cao ◽  
Ignacio Gil ◽  
Muhammad Irshad khan
Keyword(s):  
Split Ring Resonator ◽  
Ring Resonators ◽  
Impedance Bandwidth ◽  
Split Ring ◽  
Split Ring Resonators ◽  
Compact Size ◽  
Good Agreement ◽  
Swb Applications ◽  
Triple Band ◽  
Microstrip Feed

In this paper, a wideband antenna was designed for super-wideband (SWB) applications. The proposed antenna was fed with a rectangular tapered microstrip feed line, which operated over a SWB frequency range (1.42 GHz to 50 GHz). The antenna was implemented at a compact size with electrical dimensions of 0.16 λ × 0.27 λ × 0.0047 λ mm3, where λ was with respect to the lowest resonance frequency. The proposed antenna prototype was fabricated on a F4B substrate, which had a permittivity of 2.65 and 1 mm thickness. The SWB antenna exhibited an impedance bandwidth of 189% and a bandwidth ratio of 35.2:1. Additionally, the proposed antenna design exhibited three band notch characteristics that were necessary to eradicate interference from WLAN, WiMAX, and X bands in the SWB range. One notch was achieved by etching an elliptical split ring resonator (ESRR) in the radiator and the other two notches were achieved by placing rectangular split ring resonators close to the signal line. The first notch was tuned by incorporating a varactor diode into the ESRR. The prototype was experimentally validated with, with notch and without notch characteristics for SWB applications. The experimental results showed good agreement with simulated results.

scholarly journals A Multiband Antenna Stacked with Novel Metamaterial SCSRR and CSSRR for WiMAX/WLAN Applications

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 113
Author(s):  
Rajiv Mohan David ◽  
Mohammad Saadh AW ◽  
Tanweer Ali ◽  
Pradeep Kumar
Keyword(s):  
Split Ring Resonator ◽  
Unit Cell ◽  
Ring Resonators ◽  
Split Ring ◽  
Medium Theory ◽  
High Frequency Structure Simulator ◽  
Dimension Analysis ◽  
Unit Cells ◽  
Coaxial Feed ◽  
Triple Band

This paper presents an innovative method for the design of a triple band meta-mode antenna. This unique design of antenna finds application in a particular frequency band of WLAN and WiMAX. This antenna comprises of a square complimentary split ring resonator (SCSRR), a coaxial feed, and two symmetrical comb shaped split ring resonators (CSSRR). The metamaterial unit cell SCSRR independently gains control in the band range 3.15–3.25 GHz (WiMAX), whereas two symmetrical CSSRR unit cell controls the band in the ranges 3.91–4.01 GHz and 5.79–5.94 GHz (WLAN). This design methodology and the study of the suggested unit cells structure are reviewed in classical waveguide medium theory. The antenna has a miniaturized size of only 0.213λ0 × 0.192λ0 × 0.0271λ0 (20 × 18 × 2.54 mm3, where λ0 is the free space wavelength at 3.2 GHz). The detailed dimension analysis of the proposed antenna and its radiation efficiency are also presented in this paper. All the necessary simulations are carried out in High Frequency Structure Simulator (HFSS) 13.0 tool.

scholarly journals Design and evaluation of split-ring resonators for aptamer-based biosensors

2018 ◽  
Vol 7 (1) ◽  
pp. 101-111 ◽  
Author(s):  
Tobias Reinecke ◽  
Johanna-Gabriela Walter ◽  
Tim Kobelt ◽  
André Ahrens ◽  
Thomas Scheper ◽  
...  
Keyword(s):  
Resonance Frequency ◽  
Split Ring Resonator ◽  
Target Protein ◽  
Ring Resonators ◽  
Split Ring ◽  
Split Ring Resonators ◽  
Molecular Binding ◽  
Novel Approach ◽  
Highly Sensitive ◽  
Line Theory

Abstract. Split-ring resonators are electrical circuits, which enable highly sensitive readout of split capacity changes via a measurement of the shift in the resonance frequency. Thus, functionalization of the split allows the development of biosensors, where selective molecular binding causes a change in permittivity and therefore a change in split capacity. In this work, we present a novel approach using transmission line theory to describe the dependency between permittivity of the sample and resonance frequency. This theory allows the identification of all relevant parameters of a split-ring resonator and thus a target-oriented optimization process. Hereby all setup optimizations are verified with measurements. Subsequently, the split of a resonator is functionalized with aptamers and the sensor response is investigated. This preliminary experiment shows that introducing the target protein results in a shift in the resonance frequency caused by a permittivity change due to aptamer-mediated protein binding, which allows selective detection of the target protein.

scholarly journals Shield Optimization and Formulation of Regression Equations for Split-Ring Resonator

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Tahir Ejaz ◽  
Hamood Ur Rahman ◽  
T. Tauqeer ◽  
Adnan Masood ◽  
Tahir Zaidi
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Ring Resonator ◽  
Low Cost ◽  
Split Ring Resonator ◽  
Ring Resonators ◽  
Regression Equations ◽  
Split Ring ◽  
Optimum Result ◽  
5 Ghz

Microwave resonators are widely used for numerous applications including communication, biomedical and chemical applications, material testing, and food grading. Split-ring resonators in both planar and nonplanar forms are a simple structure which has been in use for several decades. This type of resonator is characterized with low cost, ease of fabrication, moderate quality factor, low external noise interference, high stability, and so forth. Due to these attractive features and ease in handling, nonplanar form of structure has been utilized for material characterization in 1–5 GHz range. Resonant frequency and quality factor are two important parameters for determination of material properties utilizing perturbation theory. Shield made of conducting material is utilized to enclose split-ring resonator which enhances quality factor. This work presents a novel technique to develop shield around a predesigned nonplanar split-ring resonator to yield optimized quality factor. Based on this technique and statistical analysis regression equations have also been formulated for resonant frequency and quality factor which is a major outcome of this work. These equations quantify dependence of output parameters on various factors of shield made of different materials. Such analysis is instrumental in development of devices/designs where improved/optimum result is required.

Sign in / Sign up

Export Citation Format

Share Document