Fiber cement boards modified with styrene-acrylic copolymer: An approach to address dimensional stability and cellulose fiber preservation

2020 ◽  
pp. 002199832095122
Author(s):  
EO Cruz ◽  
MJ Radler ◽  
M Perello ◽  
H Savastano Jr
Keyword(s):  
Transition Zone ◽  
Dimensional Stability ◽  
Cellulose Fiber ◽  
Ethylene Vinyl Acetate ◽  
Acrylic Copolymer ◽  
Cement Interface ◽  
Mechanical And Physical Properties ◽  
Interface Transition Zone ◽  
Styrene Butadiene ◽  
The Impact

The performance of polymers such as acrylics, styrene-acrylics, styrene-butadiene, ethylene vinyl acetate, type added in cementitious composites are well reported in the literature to boost properties in the fresh mortar stage as workability, anti-bleeding, and hard stage as deformation, adhesion strength, crack bridging, cohesion, durability and reduced water uptake. Polymer treatment was performed in fiber cement boards by adding 5% w/w (dry basis) of styrene-acrylic copolymer aiming to investigate the impact on the mechanical and physical properties at initial curing period (28 days) and after the 200 soak and drying ageing cycles. Dimensional stability at 28 days and the cellulose fiber/cement interface transition zone were assessed by scanning electron microscopy combined with dispersive energy X-ray spectroscopy (EDS). These experiments confirmed that the water absorption value in polymer modified cement boards was reduced by 50% after the ageing cycles when compared to the unmodified boards. Additionally, improvements on board’s rigidity with reduction of modulus of elasticity (MOE) values up to 40% and 15% reduction of board shrinkage was noticed, enhancing boards dimensional stability and preventing fibers from the mineralization process by keeping the cellulose fiber adhered on the cementitious matrix, providing a dense and cohesive fiber-cement interface transition zone after the ageing cycles. This achievement can open important fields of application for the reinforcement of flat panels.

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

Rheological studies of SBS/EVA blends modified with bio-based cashew nut shell liquid

2021 ◽  
pp. 009524432199040
Author(s):  
Isabela Pinto Ferreira ◽  
Alex da Silva Sirqueira ◽  
Taiane Andre dos Santos ◽  
Monica Feijo Naccache ◽  
Bluma Guenther Soares
Keyword(s):  
Ethylene Vinyl Acetate ◽  
Rheological Parameters ◽  
Creep Recovery ◽  
Cashew Nut Shell Liquid ◽  
Cashew Nut ◽  
Curve Fit ◽  
Significant Difference ◽  
Cashew Nut Shell ◽  
S Model ◽  
Styrene Butadiene

Research on bio-plasticizers is a topic of strategic interest in polymer blends. A bio-plasticizer, cashew nut shell liquid (CNSL), was studied in blends of ethylene-vinyl acetate copolymer (EVA) and styrene-butadiene-styrene copolymer (SBS). In the literature does not report the addition of plasticizers to SBS/EVA blend. Statistical analyses showed that there was a significant difference in mechanical properties (tension at break, hardness and elongation at break) vs. the unplasticized blend. The minimum CNSL concentration required for a statistical difference was 10 phr. The Carreau-Yasuda rheological model was used to obtain rheological parameters in these blends. The plasticizing influence of CNSL was confirmed by rheology. The effects of CNSL on creep and recovery were evaluated for the SBS/EBA blends. Burger´s model explained well SBS/EVA creep compliance. Moreover, its parameters (Newtonian dashpots and Hookean springs) were evaluated as a function of the CNSL concentrations. The bio-plasticizer concentration influenced significant correlations among the rheological creep-recovery tests, thus enabling a considerable increase in the elastic phase. Experimental creep-recovery data and curve fit were in good agreement.

Toughening of Polypropylene-Ethylene Copolymer with Nanosized CaCO3 and Styrene-Butadiene-Styrene

2007 ◽  
Vol 121-123 ◽  
pp. 1451-1454
Author(s):  
Jian Feng Chen ◽  
Guo Quan Wang ◽  
Xiao Fei Zeng ◽  
Hong Ying Zhao
Keyword(s):  
Average Particle Size ◽  
Average Particle ◽  
Single Screw Extruder ◽  
Roll Mill ◽  
The Matrix ◽  
Ethylene Copolymer ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
The Impact ◽  
Butadiene Styrene

Nanocomposites of nanosized-CaCO3/polypropylene-ethylene copolymer (PPE) and nanosized CaCO3/ PPE/ styrene-butadiene-styrene (SBS) were prepared by using two-roll mill and single screw extruder. The average particle size of nanosized CaCO3 was determined to be about 30 nm. By adding nanosized CaCO3 into PPE matrix, the toughness of the matrix improves significantly. At nanosized CaCO3 content of 12 phr (parts per hundred PPE resin by weight), the impact strength of CaCO3/PPE at room temperature reaches 61.6 KJ/m2, which is 3.02 times that of unfilled PPE matrix. In addition, the synergistic toughening effect of nanosized CaCO3 and SBS particles on PPE matrix was investigated.

The Formation Mechanism of Equiaxed Crystals in Pure Aluminum Solidification Structure under the Al-Ti-C Master Alloy

2013 ◽  
Vol 668 ◽  
pp. 865-869
Author(s):  
Wan Wu Ding ◽  
Wen Jun Zhao ◽  
Tian Dong Xia
Keyword(s):  
Transition Zone ◽  
Formation Mechanism ◽  
Master Alloy ◽  
Heterogeneous Nucleation ◽  
Pure Aluminum ◽  
Solidification Structure ◽  
Impact Mechanism ◽  
Tic Particle ◽  
The Impact

The influence of different solidified velocities on the structure of pure aluminum during the process of refinement by Al-5Ti-0.6C master alloy was studied and the impact mechanism was discussed. The results show that at the same solidified velocity, with the increase of the amount of Al-5Ti-0.6C master alloy, in the solidified structure of pure aluminum, columnar crystals will gradually decrease, while equiaxed crystals will gradually increase. But in the case when the level of addition is the same, the faster the solidified velocity, the greater the number of equiaxed crystals will be in the ingot microstructure. The formation of equiaxed crystals is the result of the dual role of dissociation of crystal particles and heterogeneous nucleation of “TiC particle---Ti transition zone”.

The modification of bitumen with styrene–butadiene–styrene, ethylene vinyl acetate and varying the amount of reactive ethylene terpolymer

2017 ◽  
Vol 50 (3) ◽  
pp. 241-255 ◽  
Author(s):  
Seyfullah Keyf
Keyword(s):  
Vinyl Acetate ◽  
Softening Point ◽  
Elastic Recovery ◽  
Ethylene Vinyl Acetate ◽  
Modified Bitumen ◽  
Penetration Index ◽  
Different Types ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Butadiene Styrene

In this article, 50/70 penetration grade TUPRAS bitumen was modified. Reactive elastomeric terpolymer (Elvaloy RET; DuPont Company), ethylene vinyl acetate (EVA) and styrene–butadiene–styrene (SBS) polymers were used in bitumen modification. Set hours of the tests were applied to samples taken from the obtained modified bitumen mixture. Varying amount of reactive ethylene terpolymer with weight ratios of 0.5%, 1.0%, 1.5%, 2.0% and 2.5% were introduced to the mixture of raw bitumen with 1.0% SBS and 1.0% EVA. Penetration, penetration index, softening point, ductility and elastic recovery tests were performed with these modified bitumen and raw bitumen. The samples of raw bitumen and modified bitumens of 2.0% Elvaloy RET, 1.0% SBS and 1.0% EVA were investigated by means of IR spectroscopy. The raw bitumen was modified with SBS, EVA and RET, and it was determined that penetration and ductility values were decreased while penetration index, softening point and elastic recovery were increased. The purpose of this study is to research the improving properties of 50/70 penetration grade–modified bitumen used in highways of Turkey. The most important characteristics (such as softening point, penetration and % elastic recovery) of new polymer-modified bitumen (NPMB) containing 2.5% EVA, 1% RET and 1% SBS were compared with eight different types of polymer-modified bitumens in Turkey (TPMB). NPMB provided all required parameters (softening point, penetration and % elastic recovery) for five different types of TPMBs (TPMB 70-16, TPMB 70-22, TPMB 76-16, TPMB 76-22 and TPMB 82-16).

scholarly journals Changes in the cellulose fiber wall supramolecular structure during the initial stages of chemical treatments of wood evaluated by NMR and X-ray scattering

Cellulose ◽  
2021 ◽  
Vol 28 (7) ◽  
pp. 3951-3965
Author(s):  
Elisabet Brännvall ◽  
P. Tomas Larsson ◽  
Jasna S. Stevanic
Keyword(s):  
Supramolecular Structure ◽  
Aggregate Size ◽  
Cellulose Fiber ◽  
Effect Of Temperature ◽  
Cellulose Fibril ◽  
X Ray ◽  
X Ray Scattering ◽  
Fiber Wall ◽  
The Impact ◽  
Ray Scattering

AbstractThe effect of initial stages of pulping of spruce, resembling prehydrolysis and alkaline cooking was studied using CP/MAS 13C-NMR, X-ray scattering, FSP and carbohydrate composition in order to study the impact of the pre-treatments on the fiber wall nanostructure. Removal of fiber wall components, hemicellulose and lignin, increased the fiber wall porosity and induced cellulose fibril aggregation. The effect of temperature and pH in the treatment on cellulose fibril aggregate size appears to be secondary. It is the removal of hemicellulose that has a profound effect on the supramolecular structure of the cellulose fiber wall. As the amount of hemicellulose dissolved from wood increases, the fibril aggregate size determined by NMR increases as well, ranging from 16 to 28 nm. Specifically, a good correlation between the amount of glucomannan in the fiber wall and the fibril aggregate size is seen. The lower the amount of glucomannan, the larger the aggregate size. Glucomannan thus seems to prevent aggregation as it acts as a very efficient spacer between fibrils. Elemental fibril size determined by NMR, was quite similar for all samples, ranging from 3.6 to 4.1 nm. By combining measurement methods, a more well-resolved picture of the structural changes occurring during was obtained.

scholarly journals Investigation of the influence of recyclate content on Poisson number of composites

2021 ◽  
Vol 28 (1) ◽  
pp. 668-675
Author(s):  
Daria Żuk ◽  
Norbert Abramczyk ◽  
Sebastian Drewing
Keyword(s):  
Testing Machine ◽  
Solid Material ◽  
Measuring System ◽  
Variable Load ◽  
Low Weight ◽  
Mechanical And Physical Properties ◽  
Static Tensile ◽  
Composite Production ◽  
The Impact ◽  
Made In

Abstract Composite materials are used in many industries. Their mechanical and physical properties as well as their low weight make them suitable for use in many constructions. Their wide application generates a problem with their disposal. Therefore, it is necessary to design new materials based on waste from polyester–glass laminates in order to introduce a closed circuit in the composite production process. The article presents research aimed at determining solid material composites with polyester–glass recyclate, in order to use these materials for modeling the structure. The aim of this study was to determine the effect of the addition of recyclate to the polyester–glass composite on the deformation and the value of the Poisson number of the material. During the study, samples from composites with the addition of polyester–glass recyclate were used. Samples made in accordance with the standard for plastics PN-EN ISO 527-4_2000P were subjected to static tensile test on a universal testing machine, with variable load parameters. During the test, the longitudinal and transverse elongations of the samples were measured using a strain gauge measuring system. On the basis of the measurements, the values of Poisson numbers were determined, which allowed for a preliminary assessment of the impact of the recyclate content in the composite on its deformability.

Sign in / Sign up

Export Citation Format

Share Document