PU composites based on different types of textile fibers

2021 ◽  
pp. 002199832110316
Author(s):  
Nuno Gama ◽  
B Godinho ◽  
Ana Barros-Timmons ◽  
Artur Ferreira
Keyword(s):  
Thermal Conductivity ◽  
Raw Materials ◽  
Natural Fibers ◽  
Tensile Modulus ◽  
High Water ◽  
Textile Fibers ◽  
Synthetic Fibers ◽  
Hydrophilic Nature ◽  
Different Types ◽  
Recycled Composites

In this study polyurethane (PU) residues were mixed with residues of textile fibers (cotton, wool and synthetic fibers up to 70 wt/wt) to produce 100% recycled composites. In addition, the effect of the type of fiber on the performance of the ensuing composites was evaluated. The presence of fibers showed similar effect on the density, reducing the density in the 5.5-9.0% range. In a similar manner, the addition of fillers decreased their thermal conductivity. The 70 wt/wt wool composite presented 38.1% lower thermal conductivity when compared to the neat matrix, a reduction that was similar for the other type of fibers. Moreover, the presence of fillers yields stiffer materials, especially in the case of the Wool based composites, which with 70 wt/wt of filler content increased the tensile modulus of the ensuing material 3.4 times. This was attributed to the aspect ratio and stiffness of this type of fiber. Finally, the high-water absorption and lower thermal stability observed, especially in the case of the natural fibers, was associated with the hydrophilic nature of fibers and porosity of composites. Overall, the results suggest that these textile-based composites are suitable for construction and automotive applications, with the advantage of being produced from 100% recycled raw-materials, without compromised performance.

Thermal Conductivity and Mechanical Properties of Wood Sawdust/Polycarbonate Composites

2012 ◽  
Vol 714 ◽  
pp. 139-146 ◽  
Author(s):  
Wittawut Wimonsong ◽  
Poonsub Threepopnatkul ◽  
Chanin Kulsetthanchalee
Keyword(s):  
Thermal Conductivity ◽  
Interfacial Adhesion ◽  
Raw Materials ◽  
Tensile Modulus ◽  
Treated Wood ◽  
Filler Loading ◽  
Polymeric Matrix ◽  
Silane Coupling Agents ◽  
Wood Sawdust ◽  
Trimethoxy Silane

Wood sawdust was increasingly being used as reinforcement in commercial thermoplastics due to low cost, reusable raw materials. One of the problems of using wood sawdust is its interfacial adhesion with polymeric matrix. In this research, two types of silane coupling agents (N-(3-Trimethoxysilylpropyl) diethyllenetriamine and γ-aminopropyl trimethoxy silane) and sodium hydroxide were used for the modification of interfacial adhesion in wood sawdust/polycarbonate composites. The effects of chemical treatment and wood sawdust content (10, 20 and 30 % by wt) were investigated by Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), thermal conductivity analysis. Youngs modulus of composites was in general higher than the neat PC except for the one with γ-aminopropyl trimethoxy silane treatment. Tensile modulus of composites was increased as the filler loading increased. Nevertheless, the addition of wood sawdust resulted in the tensile strength reduction of the composites. The SEM micrographs reveal that the aggregation of wood particles and weak interfacial bond between the treated wood sawdust and the polymeric matrix with increasing filler loading. Furthermore, the thermal conductivity was reduced significantly with the increment of wood sawdust contents.

scholarly journals Properties of Fibrous Composites with Polyester: A Comparative Analysis Between Sisal Fiber and Pet

2020 ◽  
Vol 3 (4) ◽  
pp. 334-340
Author(s):  
Matheus Vinicius Falcão Moreira ◽  
Lorrane Carneiro Laranjeira Silva ◽  
Joyce Batista Azevedo ◽  
Pollyana da Silva Melo Cardoso ◽  
Josiane Dantas Viana Barbosa ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Raw Materials ◽  
Natural Fibers ◽  
Impact Resistance ◽  
Sisal Fiber ◽  
Reinforced Composites ◽  
Fiber Concentration ◽  
Synthetic Fibers ◽  
New Material ◽  
Sisal Fibers

Fiber-reinforced composites represent 75% of the application of these materials in several industrial segments. It has the purpose of improving technical characteristics and reducing environmental impact through the use of sustainable raw materials such as natural fibers and other fibers from industrial waste. In this sense, the objective of this work was to study and compare the mechanical properties of polyester composites (PL) reinforced with natural sisal fiber and residues of polyethylene terephthalate (PET) synthetic fibers. Initially, we evaluated the moisture and morphology of the fibers. The composites with PL matrix were obtained and the fiber concentration varied by 1%, 3%, and 5% by weight. In the composites, the mechanical properties under flexion and impact resistance were evaluated. We concluded that the level of reinforcement with sisal fibers did not significantly affect the mechanical properties. However, the PET fiber provided significant improvements in the properties of the composite. Thus, the composites reinforced with PET fiber residue have advantages in the development of new material with sustainable characteristics.  

scholarly journals Optimization of extraction techniques for processing and utilization of Cyperus Dichrostachus A. Rich Plant as fiber

2022 ◽  
Author(s):  
BELETE BAYE Gelaw ◽  
Tamrat Tesfaye
Keyword(s):  
Textile Industry ◽  
Raw Materials ◽  
Energy Requirement ◽  
Natural Fibers ◽  
Extraction Methods ◽  
High Price ◽  
Process Conditions ◽  
Synthetic Fibers ◽  
Fiber Yield ◽  
Green Materials

Abstract The Textile industry is an important contributor to the GDP of countries worldwide. Both natural and synthetic fibers are the main raw materials for this sector. Environmental concerns, depletion of non-renewable resources, the high price of oil and limited oil reserves with consumer demand is driving research into cheap, biodegradable, sustainable, renewable and abundantly available green materials. Natural fibers are of the good substitute sources for swapping synthetic fibers and reinforcing polymer matrices because of their contributions in maintaining of ecology, nature of disposal, low energy requirement for processing and sustainability. The current research emphases on evaluating and determining the best extraction methods to process and treat cyperus Dichrostachus A.Rich plant in order to make the fiber suitable for variety of applications. Cyperus Dichrostachus A.Rich plant was treated with two conditions (cold and warm conditions) using statistically planned tests. Process conditions were optimised using central composite design methodology with the experimental design. Under optimised conditions, the strength and fiber yield of CDA fibers were significantly compared. The strength and fiber yield of the fiber was at maximized with optimized conditions and use for valorisation applications.

Scanning Electron Micrsocopy of Various Natural Textile Fibers

1998 ◽  
Vol 4 (S2) ◽  
pp. 834-835
Author(s):  
Gisela Buschle-Diller
Keyword(s):  
Raw Materials ◽  
Natural Fibers ◽  
Plant Fibers ◽  
Renewable Raw Materials ◽  
Synthetic Fibers ◽  
Chemical Treatments ◽  
Processing Steps ◽  
Microscopic Techniques ◽  
Scanning Electron

Plant fibers such as cotton, hemp and flax have been cultivated for textile purposes for thousands of years. These natural fibers play an important role in daily life as apparel fibers since they provide unique comfort properties unsurpassed by synthetic fibers. However, their use is not limited to the apparel sector. In recent years the market share of consumer textiles and industrial products made from all kinds of natural fibers has tremendously increased as they present a valuable source of renewable raw materials. Investigating their surface features by microscopic techniques is important to control the performance of the desired end-product. Processing steps involving heat, light or exposure to chemicals might have a significant impact on the specific surface properties of a fiber whether or not this was originally intended. Scanning electron microscopy is therefore a very useful tool for the characterization of textile products to determine the effectiveness and eventual resulting damage from physical or chemical treatments.

Effect of surface modification on mechanical properties of filature silk waste and nanoclay filler-based polymer matrix composite

2021 ◽  
pp. 096739112110230
Author(s):  
Rahul Nair ◽  
Abhishek Bhattacharya ◽  
Papiya Bhowmik ◽  
Ravi Kant
Keyword(s):  
Mechanical Properties ◽  
Surface Modification ◽  
Tensile Properties ◽  
Low Cost ◽  
Natural Fibers ◽  
Tensile Modulus ◽  
Forming Process ◽  
Synthetic Fibers ◽  
Alternative Reinforcement ◽  
Effect Of Surface

Natural fibers have been attracting researchers and engineers as an alternative reinforcement of synthetic fibers in polymer composites due to their low cost, availability from natural resources, satisfactory high modulus and tensile strength, and biodegradability. Filature silk waste (FSW) is the remnant part of the cocoons which is produced during the silk forming process. The current study focuses on the comparison of tensile properties between untreated filature silk waste reinforced epoxy-based composite (UTFSWREC), 2 wt% alkali-treated filature silk waste reinforced epoxy-based composites (TFSWREC) and 2 wt% alkali-treated filature silk waste reinforced epoxy nanocomposites (TFSWRENC). The tensile properties showed that Young’s modulus of composites increases with surface modification of fiber and further enhances with nanoclay filler. TFSWREC and TFSWRENC displayed a higher tensile modulus than UTFSWREC. Scanning Electron Microscopy (SEM) showed the removal of the sericin layer from the surface of fiber, which resulted in the separation of fibrils and further resulted in the enhancement of the mechanical properties. FTIR analysis confirmed that intermolecular bonding improves with the chemical treatment and further refined with nanoclay filler addition.

scholarly journals POTENTIAL OF RICE STRAW AS A NATURAL FIBER MATERIAL FOR COMMERCIAL PRODUCTS

2021 ◽  
Vol 15 (2) ◽  
pp. 71
Author(s):  
Lulu Fahriah Lihawa ◽  
Itsna Wafiyatul Izzah ◽  
Khairum Hawari Qolbiyah Siregar ◽  
Kurnia Syarafina Ramadhanti ◽  
Harum Azizah Darojati
Keyword(s):  
Rice Straw ◽  
Natural Fiber ◽  
Raw Materials ◽  
Natural Fibers ◽  
Cellulose Fiber ◽  
Fiber Material ◽  
Nuclear Radiation ◽  
Commercial Products ◽  
Synthetic Fibers ◽  
Natural Cellulose

Cellulose is a material used in producing natural fibers, which is more environmentally friendly than synthetic fibers. Rice straw waste contains much cellulose and has potential as natural fiber. However, before the natural cellulose fiber is extracted from the rice straw, it must pass through several processes, such as chemicals or nuclear radiation, especially during the pretreatment process. Furthermore, the resulting natural fibers are utilized to replace synthetic fibers for use as raw materials in manufacturing several commercial products. This review describes a process that can be applied to manufacture natural fibers from rice straw and commercial products made from natural cellulose fibers.

A Review on Milkweed Fiber Properties as a High-Potential Raw Material in Textile Applications

2016 ◽  
Vol 46 (6) ◽  
pp. 1412-1436 ◽  
Author(s):  
Sanaz Hassanzadeh ◽  
Hossein Hasani
Keyword(s):  
Raw Materials ◽  
Natural Fibers ◽  
Process Condition ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Technical Application ◽  
Synthetic Fibers ◽  
Functional Behavior ◽  
Application Fields ◽  
Available Information

Importance of solving the environmental pollution has attracted lots of designers and engineers’ attentions towards finding different available solutions such as substituting polymer-based raw materials with the natural ones. Thus, significant efforts applied by the researchers are generally involved to find new recourses of natural fibers instead of using the petroleum-based synthetic fibers. Among the variety of newly known natural resources, Milkweed is categorized as a versatile substitutive fiber with numerous unique properties which are mainly attributed to their hollowness structures. The presence of hollow channel along the fiber length is responsible for their lightweight and good insulation properties. Because of the fibers’ ecological and chemical benefits, numerous technical application fields could be considered for the eco-friendly and non-allergenic textiles made of Milkweed fibers especially in production of medical goods. Since morphological aspects as well as physical and mechanical properties of the Milkweed fibers significantly affect their functional behavior during their end uses, here in this review paper it is aimed to summarize all the available information regarding the fibers’ characteristics and properties. Having fundamental knowledge about the spin-ability of Milkweed fibers as well as finding the optimized process condition for their carding operation is considered to be the important points for obtaining such applicable textile products with desired properties.

scholarly journals Highly Efficient Glass Ceramic Thermal Insulation

2021 ◽  
Vol 263 ◽  
pp. 01017
Author(s):  
Ivan Vedyakov ◽  
Vladimir Vaskalov ◽  
Nikolai Maliavski ◽  
Mikhail Vedyakov
Keyword(s):  
Thermal Conductivity ◽  
Water Absorption ◽  
Thermal Insulation ◽  
Water Resistance ◽  
Raw Materials ◽  
High Water ◽  
New Production ◽  
Foaming Agent ◽  
Applied Technology ◽  
Foaming Temperature

Alkali-silicate thermal insulation materials (foam silicates) belong to the group of mineral heat insulators. Their main disadvantage is insufficient water resistance, to increase which special water-strengthening additives are introduced into materials. The aim of this work was to obtain and study foam silicates in granular (FGCG) and slab (FGCS) forms using a new production technology characterized by a simple one-stage technological scheme. Natural or technogenic amorphous silica, glassy sodium silicate (with the addition of carbonate or hydroxide) and a carbon-containing foaming agent, were used as the raw materials. Some part of the silica component was included in the binder solution, which made it possible to increase the silicate modulus in the final product to 5-10. This factor together with rather high Al2O3 concentration in the silica raw, made it possible to obtain foamed materials of very high water resistance. Another feature of the applied technology was a high foaming temperature (750–900°C). This factor makes a significant contribution to improving the water resistance of foam silicates, and significantly reducing their thermal conductivity and water absorption. As a result, FGCG was obtained with a bulk density of 170-440 kg/m3 (for FGCS – 300-400 kg/m3), a compressive strength in a cylinder of 0.5-6.3 MPa, a thermal conductivity of 0.046-0.084 W/(m·K) and a water absorption of 7.8-13.5% by volume. Mass loss of the specimens in boiling water was 0.12-0.33%, which puts obtained foamed materials on a par with most waterproof foam silicates being produced today.

scholarly journals Thermal Characterization of Recycled Materials for Building Insulation

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3564
Author(s):  
Arnas Majumder ◽  
Laura Canale ◽  
Costantino Carlo Mastino ◽  
Antonio Pacitto ◽  
Andrea Frattolillo ◽  
...  
Keyword(s):  
Environmental Impact ◽  
Environmental Sustainability ◽  
Building Materials ◽  
Raw Materials ◽  
Natural Fibers ◽  
Thermal Characterization ◽  
Recycled Materials ◽  
Building Insulation ◽  
Operational Phase

The building sector is known to have a significant environmental impact, considering that it is the largest contributor to global greenhouse gas emissions of around 36% and is also responsible for about 40% of global energy consumption. Of this, about 50% takes place during the building operational phase, while around 10–20% is consumed in materials manufacturing, transport and building construction, maintenance, and demolition. Increasing the necessity of reducing the environmental impact of buildings has led to enhancing not only the thermal performances of building materials, but also the environmental sustainability of their production chains and waste prevention. As a consequence, novel thermo-insulating building materials or products have been developed by using both locally produced natural and waste/recycled materials that are able to provide good thermal performances while also having a lower environmental impact. In this context, the aim of this work is to provide a detailed analysis for the thermal characterization of recycled materials for building insulation. To this end, the thermal behavior of different materials representing industrial residual or wastes collected or recycled using Sardinian zero-km locally available raw materials was investigated, namely: (1) plasters with recycled materials; (2) plasters with natural fibers; and (3) building insulation materials with natural fibers. Results indicate that the investigated materials were able to improve not only the energy performances but also the environmental comfort in both new and in existing buildings. In particular, plasters and mortars with recycled materials and with natural fibers showed, respectively, values of thermal conductivity (at 20 °C) lower than 0.475 and 0.272 W/(m⋅K), while that of building materials with natural fibers was always lower than 0.162 W/(m⋅K) with lower values for compounds with recycled materials (0.107 W/(m⋅K)). Further developments are underway to analyze the mechanical properties of these materials.

scholarly journals Modified Nanoclays/Straw Fillers as Functional Additives of Natural Rubber Biocomposites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 799
Author(s):  
Justyna Miedzianowska ◽  
Marcin Masłowski ◽  
Przemysław Rybiński ◽  
Krzysztof Strzelec
Keyword(s):  
Natural Rubber ◽  
Raw Materials ◽  
Research Work ◽  
Damping Properties ◽  
Main Research ◽  
Functional Additives ◽  
Different Types ◽  
Elastomeric Materials ◽  
Research Goal ◽  
The Impact

Increasingly, raw materials of natural origin are used as fillers in polymer composites. Such biocomposites have satisfactory properties. To ensure above-average functional properties, modifications of biofillers with other materials are also used. The presented research work aimed to produce and characterize elastomeric materials with a straw-based filler and four different types of montmorillonite. The main research goal was to obtain improved functional parameters of vulcanizates based on natural rubber. A series of composites filled with straw and certain types of modified and unmodified nano-clays in various ratios and amounts were prepared. Then, they were subjected to a series of tests to assess the impact of the hybrids used on the final product. It has been shown that the addition of optimal amounts of biofillers can, inter alia, increase the tensile strength of the composite, improve damping properties, extend the burning time of the material and affect the course of vulcanization or cross-linking density.

Sign in / Sign up

Export Citation Format

Share Document