Study of wear losses and frictional heat dissipation during dry sliding wear of ilmenite reinforced Al-alloy composite

2022 ◽  
pp. 095440622110637
Author(s):  
Varun Singhal ◽  
Om Prakash Pandey
Keyword(s):  
Cast Iron ◽  
Wear Rate ◽  
Heat Dissipation ◽  
Wear Behavior ◽  
Solid Lubrication ◽  
Frictional Heat ◽  
Dry Sliding Wear ◽  
Wear Loss ◽  
Dry Sliding ◽  
Al Alloy

In this investigation, ilmenite mineral reinforced Al–Si alloy matrix composite (AMC) has been developed. The wear behavior of the developed composites has been studied for their end application as break drum material to replace cast iron used in automobile industries. Ilmenite is one of the major sea beach mineral. AMC has been prepared through a low-cost stir-casting method in which 1 wt.% graphite (Gr)/tin (Sn) as a solid lubricant has been added during the fabrication of composites itself. The optical micrographs of AMC revealed uniform distribution of ilmenite particles throughout the matrix. The wear rate of the base LM30 alloy containing 17% Si and the developed composites has been studied at different normal loads at a constant velocity of 1.6 m.s−1. Optimized data revealed a significant wear rate reduction due to solid lubrication provided by Gr/Sn (∼32%). The wear rate of composites has been compared with traditional cast iron used in brake drums under similar experimental conditions. Composites exhibit nearly identical wear behavior throughout the test. The microstructural study of wear track and debris revealed that Sn and Gr used as solid lubricants played a vital role in reducing the wear loss of the prepared composites. A theoretical study of frictional heat generated during dry sliding and its dissipation has been done to establish the operative wear mechanism in the composites.

Dry Sliding Wear Behavior of 2218 Al-Alloy-Al2O3(TiO2) Hybrid Composites

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Vineet Tirth
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Aged Alloy ◽  
Dry Sliding ◽  
Al Alloy ◽  
Mathematical Relationship ◽  
Sliding Distance

AA2218–Al2O3(TiO2) composites are synthesized by stirring 2, 5, and 7 wt % of 1:2 mixture of Al2O3:TiO2 powders in molten AA2218 alloy. T61 heat-treated composites characterized for microstructure and hardness. Dry sliding wear tests conducted on pin-on-disk setup at available loads 4.91–13.24 N, sliding speed of 1.26 m/s up to sliding distance of 3770 m. Stir cast AA2218 alloy (unreinforced, 0 wt % composite) wears quickly by adhesion, following Archard's law. Aged alloy exhibits lesser wear rate than unaged (solutionized). Mathematical relationship between wear rate and load proposed for solutionized and peak aged alloy. Volume loss in wear increases linearly with sliding distance but drops with the increase in particle wt % at a given load, attributed to the increase in hardness due to matrix reinforcement. Minimum wear rate is recorded in 5 wt % composite due to increased particles retention, lesser porosity, and uniform particle distribution. In composites, wear phenomenon is complex, combination of adhesive and abrasive wear which includes the effect of shear rate, due to sliding action in composite, and abrasive effect (three body wear) of particles. General mathematical relationship for wear rate of T61 aged composite as a function of particle wt % load is suggested. Fe content on worn surface increases with the increase in particle content and counterface temperature increases with the increase in load. Coefficient of friction decreases with particle addition but increases in 7 wt % composite due to change in microstructure.

Dry Sliding Wear Behavior of Cast A7075 and A7075/SAF 2205 Composite Material

2016 ◽  
Vol 35 (5) ◽  
pp. 487-492
Author(s):  
Ahmet Karaaslan ◽  
Alptekin Kısasöz ◽  
Ş. Hakan Atapek ◽  
Kerem Altuğ Güler
Keyword(s):  
Weight Loss ◽  
Composite Material ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Cast Material ◽  
Saf 2205 ◽  
Wear Tests

AbstractThe wear behavior of cast A7075 and A7075/SAF 2205 composite material fabricated by vacuum-assisted investment flask casting was investigated under dry sliding condition. The wear tests were carried out using a “ball-on-disc” type tribometer. In the wear tests, 100Cr6 and ZrO2 balls were used as counterparts and the load, total distance and rotating speed were selected as 10 N, 100 m and 100 rpm, respectively. The results were evaluated using the friction coefficient–distance diagram, weight loss and wear rate. All worn surfaces were examined by scanning electron microscope and wear characteristics of the materials were discussed as a function of the microstructural features. It was concluded that composite material had lower friction coefficient, less weight loss and slower wear rate than that of cast material.

Garnet and Al-flyash composite under dry sliding conditions

2017 ◽  
Vol 52 (17) ◽  
pp. 2281-2288 ◽  
Author(s):  
S Sivakumar ◽  
S Senthil Kumaran ◽  
M Uthayakumar ◽  
A Daniel Das
Keyword(s):  
Genetic Algorithm ◽  
Wear Rate ◽  
Process Parameters ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding

The dry sliding wear behaviour of LM 24 aluminum alloy composites reinforced with garnet particles was evaluated. Stir casting technique was used to fabricate the composites. A pin-on-disc wear-testing machine was used to evaluate the wear rate, in which an EN 24 steel disc was used as the counterface. Results indicated that the wear rates of the composites were lower than that of the matrix alloy and further decreased with the increase in garnet content. However, in both unreinforced and reinforced composites, the wear rate increased with the increase in load and the sliding speed. Increase in the applied load increased the wear severity by changing the wear mechanism from abrasion to particle cracking-induced delamination wear. It was found that with the increase in garnet content, the wear resistance increased monotonically. The observations have been explained using scanning electron microscopy analysis of the worn surfaces and the subsurface of the composites. In this work, the most influencing input and output parameters have been performed and the process parameters have been prioritized using genetic algorithm. Genetic algorithm is used to optimize the most influencing input as well as output process parameters. The practical significance of applying genetic algorithm to dry sliding wear behavior process has been validated by means of computing the deviation between predicted and experimentally obtained wear behavior of metal matrix composite.

Effect of Fine TiC Particle Reinforcement on the Dry Sliding Wear Behavior of In Situ Synthesized ZA27 Alloy

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Roshita David ◽  
Rupa Dasgupta ◽  
B. K. Prasad
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Alloy ◽  
Dry Sliding Wear ◽  
Wear Volume ◽  
Dry Sliding ◽  
Material Loss

The in situ method of making zinc-aluminum composites wherein TiC has been introduced has been investigated in the present paper for its microstructural, physical, and dry sliding wear behavior and compared with the base alloy. In the present study, ZA-27 alloy reinforced with 5 and 10 vol % TiC was taken into consideration. The results indicate that the wear rate and coefficient of friction of composites were lower than that of base alloy. The material loss in terms of both wear volume loss and wear rate increases with increase in load and sliding distance, respectively, while coefficient of friction follows a reverse trend with increase in load. Better performance was obtained for 5% TiC reinforcement than with 10% probably due to agglomeration of particles resulting in nonuniform dispersion. Worn surfaces were analyzed by scanning electron microscopy (SEM) analysis.

scholarly journals “An Investigation of wear behavior of TiO2 nanoparticles mixed with Hybrid powder coating on MS material”

2021 ◽  
Vol 9 (12) ◽  
pp. 2350-2355
Author(s):  
Akshay Shinde
Keyword(s):  
Wear Resistance ◽  
Wear Rate ◽  
Tio2 Nanoparticles ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Powder Coating ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Maximum Contribution

Abstract: To improve the wear resistance of the hybrid powder coating, TiO2 nanoparticles was hot mixed to form a homogenous mixture with the powder in the range varying wt. dry sliding wear test conducted to determine the wear resistance. The experiments were design according to Taguchi L9 array to find the optimum nanoparticles content required to minimize the wear rate of the coating. ANOVA was used to determine the effect of the parameters on wear rate. It showed that reinforcement has the maximum contribution on the wear rate of the coating as compared to load and frequency. From the graph of means optimum parametric values was obtained at 2 % wt of reinforcement, 2 N load and 2 Hz frequency. The wear rate decrease with the increase in reinforcement. Keywords: Taguchi Method, Tribometer, Hybrid powder, TiO2, Wear Rate.

scholarly journals Studying The Effect of Reinforcing by Sicp on The Dry Sliding Wear Behavior and Mechanical Properties of AL- 4% CU Matrix Alloy

2013 ◽  
Vol 6 (2) ◽  
pp. 139-153
Author(s):  
Israa .A.K
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Material ◽  
Weight Percent ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Cu Alloy

This research is devoted to study the effect of addition of different weight percent from SiCp ( 2, 4, 6, 8 ) to Al– 4 Cu alloy which have been fabricated by liquid metallurgy method on the dry sliding wear behavior and mechanical properties. Wear characteristics of Al–SiC composites have been investigated under dry sliding conditions and compared with base alloy. Dry sliding wear tests have been carried out using pin-on-disk wear test under normal applied loads 5, 10, 15 and 20 N and at different sliding velocity of (2.7, 3.7, 4.7) m/sec. It was also observed that the wear rate varies linearly with increases normal applied load but lower in composites as compared to the base material. The wear mechanism appears to be oxidative for both Al – Cu alloy and composites under the given conditions of load and sliding velocity as indicated by optical microscopic of the worn surfaces. Further, it was found from the experimentation that the wear rate decreases linearly with increasing weight percent of silicon carbide. The best results have been obtained at 8 % wt SiC . We also observed that the yield strength, tensile strength increases with increasing wt% of SiC , but the ductility decreases.

Role of Zirconia Filler on Mechanical Properties and Dry Sliding Wear Behavior of Glass/Basalt Hybrid Fabric Reinforced Epoxy Composites

2019 ◽  
Vol 895 ◽  
pp. 200-205
Author(s):  
B.S. Kanthraju ◽  
Bheemappa Suresha ◽  
H.M. Somashekar
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Mechanical Test ◽  
Basalt Fiber ◽  
Wear Test ◽  
Specific Wear Rate ◽  
Dry Sliding Wear ◽  
Dry Sliding

This paper presents the effect of zirconia filler on mechanical properties and dry sliding wear of bidirectional hybrid (glass and basalt fiber) fabric reinforced epoxy (G-B/E) composites. Fabrication was done by hand layup method followed by compression molding. The effect of zirconia filler loading on mechanical characteristics like hardness, tensile and flexure of fabricated G-B/E composites were determined according to ASTM standards. Also, wear behavior under dry sliding condition was performed using pin-on-disc machine for different applied normal loads/sliding distance. Experimental results reveal that incorporation of zirconia filler improves the mechanical properties. Further, the wear test results indicated addition of zirconia into G-B/E hybrid fiber composites plays important role on specific wear rate under the tribo-conditions selected for the study. Further, inclusion of zirconia into G-B/E composites shows improved wear resistance and addition of 6 wt. % of zirconia exhibits least specific wear rate compared to other hybrid G-B/E composites. In addition, Scanning electron microscope images of selected mechanical test fractured coupons also have been discussed.

scholarly journals An investigation on dry sliding wear behavior of Al6061/ Titanium carbide/ Basalt hybrid metal matrix composites

2021 ◽  
Vol 13 (4) ◽  
pp. 139-150
Author(s):  
P. MUTHU
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Principal Component ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Matrix Composites ◽  
Relational Analysis ◽  
Grey Relational ◽  
Sliding Distance

Dry sliding wear plays an important role in selecting material for automotive and aerospace applications. Researchers have been exploring novel aluminum matrix composites (AMC), which offer minimum wear rate for various tribological applications. The present work involves multi-objective optimization for dry sliding wear behavior of Al6061 reinforced with 6 % of Titanium carbide and 4% of basalt hybrid metal matrix composites using principal component analysis (PCA)-based grey relational analysis (GRA). In this article, the effects of input variables of wear parameters such as applied load, sliding speed and sliding distance were investigated on different output responses, namely the wear rate, friction force and specific wear rate. Taguchi’s L9 orthogonal array with three-level settings was chosen for conducting experiments. Three output responses in each experiment were normalized into a weighted grey relational grade using grey relational analysis coupled with the principal component analysis. The analysis of variance indicated that sliding distance is the most influential parameter followed by load and sliding velocity that contributes to the quality characteristics. Optimal results have been verified through additional experiments.

scholarly journals Process Optimization and Wear Behavior of Red Mud Reinforced Aluminum Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Rajesh Shanmugavel ◽  
Thirumalai Kumaran Sundaresan ◽  
Uthayakumar Marimuthu ◽  
Pethuraj Manickaraj
Keyword(s):  
Wear Rate ◽  
Red Mud ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Experimental Result ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Grey Relational

This work presents the application of hybrid approach for optimizing the dry sliding wear behavior of red mud based aluminum metal matrix composites (MMCs). The essential input parameters are identified as applied load, sliding velocity, wt.% of reinforcement, and hardness of the counterpart material, whereas the output responses are specific wear rate and Coefficient of Friction (COF). The Grey Relational Analysis (GRA) is performed to optimize the multiple performance characteristics simultaneously. The Principle Component Analysis (PCA) and entropy methods are applied to evaluate the values of weights corresponding to each output response. The experimental result shows that the wt.% of reinforcements (Q=34.9%) followed by the sliding velocity (Q=34.5%) contributed more to affecting the dry sliding wear behavior. The optimized conditions are verified through the confirmation test, which exhibited an improvement in the grey relational grade of specific wear rate and COF by 0.3 and 0.034, respectively.

Sign in / Sign up

Export Citation Format

Share Document