Mechanical characterization of hydrolysis effects on the stiffness of bioabsorbable polymeric filaments: An experimental and modeling approach based on a simple constitutive damage model

2021 ◽  
pp. 096739112199882
Author(s):  
Thiago André Carniel ◽  
Paulo Bastos de Castro ◽  
André Luiz Grando Santos ◽  
Carlos Rodrigo de Mello Roesler ◽  
Everton Rafael Breitenbach ◽  
...  
Keyword(s):  
Constitutive Model ◽  
Mechanical Response ◽  
Damage Model ◽  
Damage Potential ◽  
Bioabsorbable Polymer ◽  
Modeling Approach ◽  
Fitting Procedure ◽  
Variational Framework ◽  
Specific Strain ◽  
Constitutive Parameters

This manuscript presents an experimental and modeling approach in order to characterize the stiffness loss of bioabsorbable polymer filaments due to hydrolysis. In this regard, bioabsorbable suture yarns (poly(lactic-co-glycolic) acid—PLGA) were chosen as a representative material for the present investigation. The observed mechanical response was characterized by means of a thermodynamically consistent constitutive variational framework. Usually, two different damage variables are assumed to take place in this class of materials: a hydrolytic damage (long-term degradation) and a strain-driven damage (short-term degradation). This work concerns the proposition of a constitutive model that only considers the hydrolytic damage, in which a specific strain energy and a proper dissipation damage potential were tailored to model the tested material. A nonlinear curve fitting procedure based on Particle Swarm Optimization was performed to identify the constitutive parameters. A set of numerical simulations demonstrates the effectiveness of the proposed constitutive model to predict damage-induced creep and damage-induced stress relaxation, behaviors that can be used as design criteria in absorbable implants. The main achieved results show that the proposed constitutive approach leads to a simple but effective model capable to drive the first steps in the design of absorbable biomedical devices. The present variational framework can be extended to study the constitutive response of other bioabsorbable polymers, accounting for viscous and/or plastic behaviors.

scholarly journals Rock Failure Analysis Based on a Coupled Elastoplastic-Logarithmic Damage Model

2017 ◽  
Vol 62 (4) ◽  
pp. 753-774
Author(s):  
M. Abdia ◽  
H. Molladavoodi ◽  
H. Salarirad
Keyword(s):  
Constitutive Model ◽  
Plastic Flow ◽  
Mechanical Response ◽  
Damage Model ◽  
Yield Function ◽  
Irreversible Thermodynamics ◽  
Stiffness Degradation ◽  
Shear Stresses ◽  
Rock Materials ◽  
Damage Process

Abstract The rock materials surrounding the underground excavations typically demonstrate nonlinear mechanical response and irreversible behavior in particular under high in-situ stress states. The dominant causes of irreversible behavior are plastic flow and damage process. The plastic flow is controlled by the presence of local shear stresses which cause the frictional sliding. During this process, the net number of bonds remains unchanged practically. The overall macroscopic consequence of plastic flow is that the elastic properties (e.g. the stiffness of the material) are insensitive to this type of irreversible change. The main cause of irreversible changes in quasi-brittle materials such as rock is the damage process occurring within the material. From a microscopic viewpoint, damage initiates with the nucleation and growth of microcracks. When the microcracks length reaches a critical value, the coalescence of them occurs and finally, the localized meso-cracks appear. The macroscopic and phenomenological consequence of damage process is stiffness degradation, dilatation and softening response. In this paper, a coupled elastoplastic-logarithmic damage model was used to simulate the irreversible deformations and stiffness degradation of rock materials under loading. In this model, damage evolution & plastic flow rules were formulated in the framework of irreversible thermodynamics principles. To take into account the stiffness degradation and softening on post-peak region, logarithmic damage variable was implemented. Also, a plastic model with Drucker-Prager yield function was used to model plastic strains. Then, an algorithm was proposed to calculate the numerical steps based on the proposed coupled plastic and damage constitutive model. The developed model has been programmed in VC++ environment. Then, it was used as a separate and new constitutive model in DEM code (UDEC). Finally, the experimental Oolitic limestone rock behavior was simulated based on the developed model. The irreversible strains, softening and stiffness degradation were reproduced in the numerical results. Furthermore, the confinement pressure dependency of rock behavior was simulated in according to experimental observations.

Damage Constitutive Model and Failure Mechanism of Lead-Free Solder in CBGA Package

2008 ◽  
Vol 44-46 ◽  
pp. 77-84
Author(s):  
Wei Na Hao ◽  
Guo Zhong Chai ◽  
J. Zhou
Keyword(s):  
Constitutive Model ◽  
Thermal Loading ◽  
Mechanical Response ◽  
Failure Process ◽  
Damage Model ◽  
Lead Free ◽  
Lead Free Solder ◽  
Element Analysis ◽  
Cyclic Thermal Loading ◽  
Free Solder

A viscoplastic constitutive model with void damage is developed to analyze the macroscopic mechanical response and damage mechanism of lead-free solder alloy in CBGA packaging under cyclic thermal loading. The constitutive model is implemented into ABAQUS through its user defined material subroutine. Two-dimensional nonlinear finite element analysis of a ceramic ball grid array(CBGA) package is conducted to simulate the viscoplastic deformation and damage failure process of the lead-free solder joint under cyclic thermal loading. The damage model is helpful for optimization and reliability of electronic package.

scholarly journals Wrinkling in engineering fabrics: a comparison between two different comprehensive modelling approaches

2018 ◽  
Vol 474 (2216) ◽  
pp. 20180063 ◽  
Author(s):  
I. Giorgio ◽  
P. Harrison ◽  
F. dell'Isola ◽  
J. Alsayednoor ◽  
E. Turco
Keyword(s):  
Discrete Model ◽  
Continuum Model ◽  
Mechanical Response ◽  
Image Correlation ◽  
Full Field ◽  
Explicit Finite Element ◽  
Fitting Procedure ◽  
Constitutive Parameters ◽  
The Continuum ◽  
Modelling Approaches

We consider two ‘comprehensive’ modelling approaches for engineering fabrics. We distinguish the two approaches using the terms ‘semi-discrete’ and ‘continuum’, reflecting their natures. We demonstrate a fitting procedure, used to identify the constitutive parameters of the continuum model from predictions of the semi-discrete model, the parameters of which are in turn fitted to experimental data. We, then, check the effectiveness of the continuum model by verifying the correspondence between semi-discrete and continuum model predictions using test cases not previously used in the identification process. Predictions of both modelling approaches are compared against full-field experimental kinematic data, obtained using stereoscopic digital image correlation techniques, and also with measured force data. Being a reduced order model and being implemented in an implicit rather than an explicit finite-element code, the continuum model requires significantly less computational power than the semi-discrete model and could therefore be used to more efficiently explore the mechanical response of engineering fabrics.

scholarly journals A Novel Damage Model for Strata Layers and Coal Mass

Energies ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1928 ◽  
Author(s):  
Faham Tahmasebinia ◽  
Chengguo Zhang ◽  
Ismet Canbulat ◽  
Samad Sepasgozar ◽  
Serkan Saydam
Keyword(s):  
Constitutive Model ◽  
Strain Energy ◽  
Damage Model ◽  
Rock Joint ◽  
Coal Mass ◽  
Stored Energy ◽  
Rock Interaction ◽  
Geological Factors ◽  
Coal Rock ◽  
Joint Quality

Coal burst occurrences are affected by a range of mining and geological factors. Excessive slipping between the strata layers may release a considerable amount of strain energy, which can be destructive. A competent strata is also more vulnerable to riveting a large amount of strain energy. If the stored energy in the rigid roof reaches a certain level, it will be released suddenly which can create a serious dynamic reaction leading to coal burst incidents. In this paper, a new damage model based on the modified thermomechanical continuum constitutive model in coal mass and the contact layers between the rock and coal mass is proposed. The original continuum constitutive model was initially developed for the cemented granular materials. The application of the modified continuum constitutive model is the key aspect to understand the momentum energy between the coal–rock interactions. The transformed energy between the coal mass and different strata layers will be analytically demonstrated as a function of the rock/joint quality interaction conditions. The failure and post failure in the coal mass and coal–rock joint interaction will be classified by the coal mass crushing, coal–rock interaction damage and fragment reorganisation. The outcomes of this paper will help to forecast the possibility of the coal burst occurrence based on the interaction between the coal mass and the strata layers in a coal mine.

scholarly journals Thermodynamic compatibility conditions of a new class of hysteretic materials

2021 ◽  
Author(s):  
Salvatore Sessa
Keyword(s):  
Constitutive Model ◽  
Dynamic Analysis ◽  
Closed Form ◽  
Iterative Procedure ◽  
Displacement Amplitude ◽  
Compatibility Conditions ◽  
Algebraic Functions ◽  
New Class ◽  
Thermodynamic Compatibility ◽  
Constitutive Parameters

AbstractThe thermodynamic compatibility defined by the Drucker postulate applied to a phenomenological hysteretic material, belonging to a recently formulated class, is hereby investigated. Such a constitutive model is defined by means of a set of algebraic functions so that it does not require any iterative procedure to compute the response and its tangent operator. In this sense, the model is particularly feasible for dynamic analysis of structures. Moreover, its peculiar formulation permits the computation of thermodynamic compatibility conditions in closed form. It will be shown that, in general, the fulfillment of the Drucker postulate for arbitrary displacement ranges requires strong limitations of the constitutive parameters. Nevertheless, it is possible to determine a displacement compatibility range for arbitrary sets of parameters so that the Drucker postulate is fulfilled as long as the displacement amplitude does not exceed the computed threshold. Numerical applications are provided to test the computed compatibility conditions.

scholarly journals Development of Elastoplastic-Damage Model of AlFeSi Phase for Aluminum Alloy 6061

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 954
Author(s):  
Hailong Wang ◽  
Wenping Deng ◽  
Tao Zhang ◽  
Jianhua Yao ◽  
Sujuan Wang
Keyword(s):  
Aluminum Alloy ◽  
Constitutive Model ◽  
Material Properties ◽  
Damage Model ◽  
Scratch Test ◽  
Aluminum Alloy 6061 ◽  
Ultra Precision ◽  
Simulation Results ◽  
Alloy 6061 ◽  
Elastoplastic Damage

Material properties affect the surface finishing in ultra-precision diamond cutting (UPDC), especially for aluminum alloy 6061 (Al6061) in which the cutting-induced temperature rise generates different types of precipitates on the machined surface. The precipitates generation not only changes the material properties but also induces imperfections on the generated surface, therefore increasing surface roughness for Al6061 in UPDC. To investigate precipitate effect so as to make a more precise control for the surface quality of the diamond turned Al6061, it is necessary to confirm the compositions and material properties of the precipitates. Previous studies have indicated that the major precipitate that induces scratch marks on the diamond turned Al6061 is an AlFeSi phase with the composition of Al86.1Fe8.3Si5.6. Therefore, in this paper, to study the material properties of the AlFeSi phase and its influences on ultra-precision machining of Al6061, an elastoplastic-damage model is proposed to build an elastoplastic constitutive model and a damage failure constitutive model of Al86.1Fe8.3Si5.6. By integrating finite element (FE) simulation and JMatPro, an efficient method is proposed to confirm the physical and thermophysical properties, temperature-phase transition characteristics, as well as the stress–strain curves of Al86.1Fe8.3Si5.6. Based on the developed elastoplastic-damage parameters of Al86.1Fe8.3Si5.6, FE simulations of the scratch test for Al86.1Fe8.3Si5.6 are conducted to verify the developed elastoplastic-damage model. Al86.1Fe8.3Si5.6 is prepared and scratch test experiments are carried out to compare with the simulation results, which indicated that, the simulation results agree well with those from scratch tests and the deviation of the scratch force in X-axis direction is less than 6.5%.

scholarly journals A nonlinear strain-rate dependent constitutive model for uncured rubber materials under large deformation

2020 ◽  
Vol 37 ◽  
pp. 118-125
Author(s):  
Weihua Zhou ◽  
Changqing Fang ◽  
Huifeng Tan ◽  
Huiyu Sun
Keyword(s):  
Constitutive Model ◽  
Large Deformation ◽  
Mechanical Response ◽  
Uniaxial Tensile ◽  
Hysteresis Phenomenon ◽  
Mechanical Behaviors ◽  
Nonlinear Constitutive Model ◽  
Rate Dependent ◽  
Parallel Networks ◽  
Non Gaussian

Abstract Uncured rubber possesses remarkable hyperelastic and viscoelastic properties while it undergoes large deformation; therefore, it has wide application prospects and attracts great research interests from academia and industry. In this paper, a nonlinear constitutive model with two parallel networks is developed to describe the mechanical response of uncured rubber. The constitutive model is incorporated with the Eying model to describe the hysteresis phenomenon and viscous flow criterion, and the hyperelastic properties under large deformation are captured by a non-Gaussian chain molecular network model. Based on the model, the mechanical behaviors of hyperelasticity, viscoelasticity and hysteresis under different strain rates are investigated. Furthermore, the constitutive model is employed to estimate uniaxial tensile, cyclic loading–unloading and multistep tensile relaxation mechanical behaviors of uncured rubber, and the prediction results show good agreement with the test data. The nonlinear mechanical constitutive model provides an efficient method for predicting the mechanical response of uncured rubber materials.

Calibration and Validation of an Elasto-Viscoplastic Material Model for a Hot Work Tool Steel Used in Pressure Casting Dies

2007 ◽  
Vol 345-346 ◽  
pp. 685-688 ◽  
Author(s):  
Werner Ecker ◽  
Thomas Antretter ◽  
R. Ebner
Keyword(s):  
Constitutive Model ◽  
Tool Steel ◽  
Mechanical Response ◽  
Mechanical Load ◽  
Kinematic Hardening ◽  
Ex Situ ◽  
Pressure Casting ◽  
Viscoplastic Material ◽  
Crack Network ◽  
Hot Work Tool Steel

Pressure casting dies are subjected to a large number of thermal as well as mechanical load cycles, which are leading to a characteristic thermally induced crack network on the die surface. As a typical representative for a die material the cyclic thermo-mechanical behavior of the hot work tool steel grade 1.2343 (X38CrMoV5-1) is investigated both experimentally as well as numerically. On the one hand the information from isothermal compression-tension tests is used in a subsequent analysis to calibrate a constitutive model that takes into account the characteristic combined isotropic-kinematic hardening/softening of the material. On the other hand the non-isothermal mechanical response of the material to thermal cycles is characterized by means of a periodic laser pulse applied to a small plate-like specimen which is cooled on the back. The residual stresses developing at the surface of the irradiated region of the specimen are determined ex-situ by means of X-ray diffraction. The obtained values agree well with the results of an accompanying finite-element study. This information is used to verify the calibrated constitutive model. The material law is finally used for the prediction of stresses and strains in a die.

scholarly journals Multi-Scale Analyses and Modeling of Metallic Nano-Layers

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 450
Author(s):  
Zara Moleinia ◽  
David Bahr
Keyword(s):  
Experimental Data ◽  
Constitutive Model ◽  
Crystal Plasticity ◽  
Single Layer ◽  
Adaptive Boosting ◽  
Multi Scale ◽  
Nano Scale ◽  
Boosting Technique ◽  
Constitutive Parameters ◽  
Computational Processes

The current work centers on multi-scale approaches to simulate and predict metallic nano-layers’ thermomechanical responses in crystal plasticity large deformation finite element platforms. The study is divided into two major scales: nano- and homogenized levels where Cu/Nb nano-layers are designated as case studies. At the nano-scale, a size-dependent constitutive model based on entropic kinetics is developed. A deep-learning adaptive boosting technique named single layer calibration is established to acquire associated constitutive parameters through a single process applicable to a broad range of setups entirely different from those of the calibration. The model is validated through experimental data with solid agreement followed by the behavioral predictions of multiple cases regarding size, loading pattern, layer type, and geometrical combination effects for which the performances are discussed. At the homogenized scale, founded on statistical analyses of microcanonical ensembles, a homogenized crystal plasticity-based constitutive model is developed with the aim of expediting while retaining the accuracy of computational processes. Accordingly, effective constitutive functionals are realized where the associated constants are obtained via metaheuristic genetic algorithms. The model is favorably verified with nano-scale data while accelerating the computational processes by several orders of magnitude. Ultimately, a temperature-dependent homogenized constitutive model is developed where the effective constitutive functionals along with the associated constants are determined. The model is validated by experimental data with which multiple demonstrations of temperature effects are assessed and analyzed.

Sign in / Sign up

Export Citation Format

Share Document