Strain parameters at hot rolling of aluminum strips reinforced with steel netting

2018 ◽  
Vol 22 (6) ◽  
pp. 2009-2029 ◽  
Author(s):  
M Stolbchenko ◽  
H Makeieva ◽  
O Grydin ◽  
Ya Frolov ◽  
M Schaper
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Tensile Strain ◽  
Rolling Direction ◽  
Aluminum Matrix ◽  
Tension Tests ◽  
Temperature And Pressure ◽  
Oriented Parallel ◽  
Reducing Properties ◽  
Properties Of Composites

This experiment studied the strain parameters of rolling an aluminum matrix when wire netting is inserted between aluminum layers. During the experiment, two types of stainless steel fabric netting oriented parallel and diagonal to the rolling axis were placed between two aluminum strips and rolled. Multiple rolling processes were performed in which the temperature and pressure on the material were varied to produce bonding of matrix layers. During the study, the following main investigations were made: strain on areas of longitudinal and transverse cross sections of the composite was measured; stretching and ovalization of net wiring and changes in the net cell angles were determined; mechanical properties of composites along the rolling direction were tested. The main contradiction resulting from this experiment was as follows: the contact pressure required for the bonding of aluminum layers produces extreme tensile strain on the inserted net wires, reducing the mechanical properties of the reinforcing net and thus reducing properties of the entire composite. Optimal results in the longitudinal tension tests were achieved by using strips with diagonally oriented net-reinforcement.

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

Fatigue Properties of Al-Li Plates Joined by Friction Stir Welding

2008 ◽  
Vol 385-387 ◽  
pp. 849-852 ◽  
Author(s):  
Pasquale Cavaliere ◽  
Francesco W. Panella ◽  
Antonio Squillace
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Testing Machine ◽  
Rolling Direction ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Control Mode ◽  
Fatigue Properties ◽  
Amplitude Control ◽  
Friction Stir

Al-Li alloys are characterized by a strong anisotropy in mechanical properties and microstructure with respect to the rolling direction. Plates of 2198 Al-Li alloy were friction stir welded by employing maximum rotation speed: 1000 rev/min and welding speed of 80 mm/min, both in parallel and orthogonal directions with respect to the rolling one. The joints mechanical properties were evaluated by means of tensile tests at room temperature. In addition, fatigue tests performed with a resonant electro-mechanical testing machine under constant amplitude control up to 250 Hz loading, were conducted in axial control mode with R(σmin/σmax)=0.33, for all the welding and rotating speed conditions. The fatigue crack propagation experiments were performed by employing single edge notched specimens.With the aim to characterize the weld performances, both the microstructure evolution at jointed cross sections, related to the welding variables, and the fractured surfaces were respectively analyzed by means of optical and scanning electron microscopy.

scholarly journals Direct Generation of High-Aspect-Ratio Structures of AISI 316L by Laser-Assisted Powder Deposition

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5670
Author(s):  
Piera Alvarez ◽  
M. Ángeles Montealegre ◽  
Francisco Cordovilla ◽  
Ángel García-Beltrán ◽  
Ignacio Angulo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Cross Sections ◽  
High Aspect Ratio ◽  
316L Stainless Steel ◽  
Laser Metal Deposition ◽  
Homogeneous Microstructure ◽  
Tension Tests ◽  
Powder Deposition ◽  
Direct Generation

The effect of process parameters and the orientation of the cladding layer on the mechanical properties of 316L stainless steel components manufactured by laser metal deposition (LMD) was investigated. High aspect-ratio walls were manufactured with layers of a 4.5 mm wide single-cladding track to study the microstructure and mechanical properties along the length and the height of the wall. Samples for the tensile test (according to ASTM E-8M-04) were machined from the wall along both the direction of the layers and the direction perpendicular to them. Cross-sections of the LMD samples were analyzed by optical and scanning electron microscopy (SEM). The orientation of the growing grain was observed. It was associated with the thermal gradient through the building part. A homogeneous microstructure between consecutive layers and some degree of microporosity was observed by SEM. Uniaxial tension tests were performed on samples extracted from the wall in perpendicular and parallel directions. Results for ultimate tensile strength were similar in both cases and with the wrought material. The σ0.2 were similar in both cases but slightly superior to the wrought material.

Microstructure and Mechanical Properties of Silicon Nitride Reinforced Aluminum Matrix Composites Fabricated by Pressure Infiltration

2001 ◽  
Vol 702 ◽  
Author(s):  
L.M. Peng ◽  
K. Noda ◽  
H. Kawamoto
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Pressure Casting ◽  
Matrix Composites ◽  
Microstructure And Mechanical Properties ◽  
Properties Of Composites

ABSTRACTThe present study aimed to investigate the microstructure and mechanical properties of aluminum matrix composites reinforced with high volume fraction of Si3N4 fabricated by the pressure casting technique, with variations in the composition of matrix alloy and microstructure of preforms. Characterization was carried out by a combination of metallography, flexural and load-controlled fatigue tests to study the flexural strength, fracture toughness and fatigue behavior in the composites. The findings indicated that increasing matrix strength resulted in an increase in flexural strength and fatigue resistance of composites. The fracture toughness of composites increased with the volume fraction of infiltrated tough Al phase. The CIP pressure exerted a significant effect on mechanical properties of composites. The improvement in mechanical properties of composites is associated with the load transfer effect from matrix to the stiffer reinforcement.

Spindle shaped bodies in foveolar cones of the baboon retina

1989 ◽  
Vol 47 ◽  
pp. 960-961
Author(s):  
W. Krebs ◽  
I. Krebs
Keyword(s):  
Cross Sections ◽  
Inclusion Bodies ◽  
Photoreceptor Cells ◽  
Papio Anubis ◽  
Retinal Photoreceptor ◽  
Age Related ◽  
Cone Cells ◽  
Membrane Bound ◽  
Oriented Parallel ◽  
Shaped Inclusion

Various inclusion bodies occur in vertebrate retinal photoreceptor cells. Most of them are membrane bound and associated with phagocytosis or they are age related residual bodies. We found an additional inclusion body in foveal cone cells of the baboon (Papio anubis) retina.The eyes of a 15 year old baboon were fixed by immersion in cacodylate buffered glutaraldehyde (2%)/formaldehyde (2%) as described in detail elsewhere . Pieces of retina from various locations, including the fovea, were embedded in epoxy resin such that radial or tangential sections could be cut.Spindle shaped inclusion bodies were found in the cytoplasm of only foveal cones. They were abundant in the inner segments, close to the external limiting membrane (Fig. 1). But they also occurred in the outer fibers, the perikarya, and the inner fibers (Henle’s fibers) of the cone cells. The bodies were between 0.5 and 2 μm long. Their central diameter was 0.2 to 0. 3 μm. They always were oriented parallel to the long axis of the cone cells. In longitudinal sections (Figs. 2,3) they seemed to have a fibrous skeleton that, in cross sections, turned out to consist of plate-like (Fig.4) and tubular profiles (Fig. 5).

Influence exerted by underground excavation shape and by effective stresses on the formation of a tensile strain zone at a depth greater than 1 km

2020 ◽  
pp. 67-75
Author(s):  
Van Min Nguyen ◽  
V. A. Eremenko ◽  
M. A. Sukhorukova ◽  
S. S. Shermatova
Keyword(s):  
Rock Mass ◽  
Cross Sections ◽  
Tensile Strain ◽  
Rock Fracture ◽  
Strain Analysis ◽  
Surrounding Rock ◽  
Underground Excavation ◽  
Secondary Stress ◽  
Principal Stresses ◽  
Mining Depth

The article presents the studies into the secondary stress field formed in surrounding rock mass around underground excavations of different cross-sections and the variants of principal stresses at a mining depth greater than 1 km. The stress-strain analysis of surrounding rock mass around development headings was performed in Map3D environment. The obtained results of the quantitative analysis are currently used in adjustment of the model over the whole period of heading and support of operating mine openings. The estimates of the assumed parameters of excavations, as well as the calculations of micro-strains in surrounding rock mass by three scenarios are given. During heading in the test area in granite, dense fracturing and formation of tensile strain zone proceeds from the boundary of e ≥ 350me and is used to determine rough distances from the roof ( H roof) and sidewalls ( H side) of an underground excavation to the 3 boundary e = 350me (probable rock fracture zone). The modeling has determined the structure of secondary stress and strain fields in the conditions of heading operations at great depths.

scholarly journals Effect of Boron Carbide Addition on Wear Resistance of Aluminum Matrix Composites Fabricated by Stir Casting and Hot Rolling Processes

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 989
Author(s):  
Donghyun Lee ◽  
Junghwan Kim ◽  
Sang-Kwan Lee ◽  
Yangdo Kim ◽  
Sang-Bok Lee ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Boron Carbide ◽  
Hot Rolling ◽  
Rolling Direction ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Aluminum Matrix Composites ◽  
Wear Depth ◽  
Wear Properties ◽  
B4c Particles

In this study, to evaluate the effect of boron carbide (B4C) addition on the wear performance of aluminum (Al), Al6061 and 5, 10, and 20 vol.% B4C/Al6061 composites were manufactured using the stir casting and hot rolling processes. B4C particles were randomly dispersed during the stir casting process; then, B4C particles were arranged in the rolling direction using a hot rolling process to further improve the B4C dispersion and wear resistance of the composites. Furthermore, a continuous interfacial layer between B4C and the Al6061 matrix was generated by diffusion of titanium (Ti) and chromium (Cr) atoms contained in the Al6061 alloy. Wear depth and width of the composites decreased with increasing B4C content. Furthermore, with B4C addition, coefficient of friction (COF) improved as compared with that of Al6061. The results indicate that interface-controlled, well-aligned B4C particles in the friction direction can effectively increase the wear properties of Al alloys and improve their hardness.

scholarly journals Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3603
Author(s):  
Tim Pasang ◽  
Benny Tavlovich ◽  
Omry Yannay ◽  
Ben Jakson ◽  
Mike Fry ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Electron Beam Melting ◽  
Rolling Direction ◽  
Laser Melting ◽  
Plate Rolling

An investigation of mechanical properties of Ti6Al4V produced by additive manufacturing (AM) in the as-printed condition have been conducted and compared with wrought alloys. The AM samples were built by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) in 0°, 45° and 90°—relative to horizontal direction. Similarly, the wrought samples were also cut and tested in the same directions relative to the plate rolling direction. The microstructures of the samples were significantly different on all samples. α′ martensite was observed on the SLM, acicular α on EBM and combination of both on the wrought alloy. EBM samples had higher surface roughness (Ra) compared with both SLM and wrought alloy. SLM samples were comparatively harder than wrought alloy and EBM. Tensile strength of the wrought alloy was higher in all directions except for 45°, where SLM samples showed higher strength than both EBM and wrought alloy on that direction. The ductility of the wrought alloy was consistently higher than both SLM and EBM indicated by clear necking feature on the wrought alloy samples. Dimples were observed on all fracture surfaces.

Sign in / Sign up

Export Citation Format

Share Document