Effects of drilling parameters on delamination of kenaf-glass fibre reinforced unsaturated polyester composites

2021 ◽  
pp. 152808372110620
Author(s):  
AR Ngah ◽  
Suhad D Salman ◽  
Z Leman ◽  
SM Sapuan ◽  
MFM Alkbir ◽  
...  
Keyword(s):  
Glass Fibre ◽  
Feed Rate ◽  
Unsaturated Polyester ◽  
Spindle Speed ◽  
Taguchi Methods ◽  
Drilling Process ◽  
Drill Bit ◽  
Influence Of Process Parameters ◽  
Drill Bits ◽  
Glass Fibre Reinforced

Drilling is a secondary material removal and usually carried out to facilitate fastening of parts together. Drilling of composite materials is not usually a problem-free process. Issues related to delamination composite laminates need to be addressed because it introduces the stress concentration point on the composite. This study focussed on the influence of process parameters such as spindle speed, feed rate, type of drill bits and geometry on the extend of delamination experienced by the composite during the drilling process of kenaf-glass fibre-reinforced unsaturated polyester composite, and the delamination measurements were taken under a microscope. Taguchi methods and analysis of variance were employed to find the optimal parameters. From the results, the most significant parameter was the feed rate. The minimum delamination was achieved when the feed rate was 0.05 mm/rev and spindle speed was 700r/min using both types of drill bits. The quality of the drill hole using the twist drill bit has been proven to be better than the brad drill bit.

scholarly journals Optimization of Drilling Process Parameters Via Taguchi, TOPSIS and RSA Techniques

2017 ◽  
Vol 62 (3) ◽  
pp. 1803-1812 ◽  
Author(s):  
K. Shunmugesh ◽  
K. Panneerselvam
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Research Work ◽  
Cutting Speed ◽  
High Strength ◽  
Drilling Process ◽  
Drill Bit ◽  
Influence Of Process Parameters ◽  
Light Trucks ◽  
Cfrp Composite

AbstractCarbon Fiber Reinforced Polymer (CFRP) is the most preferred composite material due to its high strength, high modulus, corrosion resistance and rigidity and which has wide applications in aerospace engineering, automobile sector, sports instrumentation, light trucks, airframes. This paper is an attempt to carry out drilling experiments as per Taguchi’s L27(313) orthogonal array on CFRP under dry condition with three different drill bit type (HSS, TiAlN and TiN). In this research work Response Surface Analysis (RSA) is used to correlate the effect of process parameters (cutting speed and feed rate) on thrust force, torque, vibration and surface roughness. This paper also focuses on determining the optimum combination of input process parameter and the drill bit type that produces quality holes in CFRP composite laminate using Multi-objective Taguchi technique and TOPSIS. The percentage of contribution, influence of process parameters and adequacy of the second order regression model is carried out by analysis of variance (ANOVA). The results of experimental investigation demonstrates that feed rate is the pre-dominate factor which affects the response variables.

Drilling Force and Chip Morphology in Drilling of PCB Supported Hole

2011 ◽  
Vol 188 ◽  
pp. 429-434 ◽  
Author(s):  
L.P. Yang ◽  
Li Xin Huang ◽  
Cheng Yong Wang ◽  
L.J. Zheng ◽  
Ping Ma ◽  
...  
Keyword(s):  
Feed Rate ◽  
Printed Circuit Board ◽  
Thrust Force ◽  
Chip Morphology ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Circuit Board ◽  
Drilling Process ◽  
Drilling Force ◽  
Drill Bits

Supported holes of Printed circuit board (PCB) are drilled with two different drill bits. Drilling force (thrust force and torque) and chip morphology are examined at different cutting parameters, and the effects of the two drills are discussed. The results indicate that the drilling force and chip morphology are affected by the feed rate, spindle speed and drill shape. Thrust force increases with the increasing feed rate, and decreases with the increasing spindle speed. Optimization of drill geometry can reduce the thrust force significantly, and is effective in chip breaking which can improve the chip evacuation during the drilling process.

scholarly journals Optimization of drilling process parameters on delamination factor of Jute reinforced unsaturated polyester composite using Box-Behnken design of experiment

2020 ◽  
Vol 14 (1) ◽  
pp. 6295-6303
Author(s):  
Zaleha Mustafa ◽  
N. H. Idrus ◽  
A B. Mohd Hadzley ◽  
D. Sivakumar ◽  
M. Y. Norazlina ◽  
...  
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Unsaturated Polyester ◽  
Spindle Speed ◽  
Drilling Process ◽  
Delamination Factor ◽  
Drilling Parameters ◽  
Polyester Composite ◽  
Tool Diameter ◽  
Drill Tool

This paper presents an investigation on the influence of the drilling parameters such as feed rate, spindle speed and drill tool diameter onto the delamination factor of the jute reinforced unsaturated polyester composite. Natural fibre based composite are mostly used for commodity application and often subjected to drilling during applications and may generate delamination of drilled holes on the workpiece. The composite was fabricated using woven jute fibre via vacuum bagging method followed a high temperature curing using hot press. The fibre was kept at 40 vol. %. The main effect and the interaction between the specified factors of feed rate (20-100mm/min), spindle speed (500-1500 rpm) and drill tool diameter (4-8 mm) with delamination factor as corresponding respond was structured via the Response Surface Methodology (RSM) based on three-level Box-Behnken design of experiment and the ANOVA. The levels of importance of the process parameters on flexural properties are determined by using Analysis of Variance (ANOVA). The optimised drilling process parameters obtained as 24.38 mm/min of feed rate, 1146.14 rpm of spindle speed and 5.51 mm drill tool diameter achieved the most minimal delamination factor. The feed rate and spindle speed were perceived as the most influential drilling parameters on the delamination factor of the jute reinforced unsaturated polyester composite.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Experiments of Drilling Titanium Alloy with Varying Operation Parameters

2017 ◽  
Vol 748 ◽  
pp. 254-258
Author(s):  
Chang Yi Liu ◽  
Bai Shou Zhang ◽  
Suman Shrestha
Keyword(s):  
Titanium Alloy ◽  
Feed Rate ◽  
Thrust Force ◽  
Maximum Amount ◽  
Spindle Speed ◽  
Drilling Process ◽  
Process Variables ◽  
Experimental Cutting ◽  
Operation Parameters ◽  
Titanium Alloy Ti6al4v

Drilling experiments of titanium alloy Ti6Al4V were conducted. Taking the speed and feed as the process variables, a set of experimental cutting forces are obtained and compared. From the experimental results it is concluded that within the experimental extent the thrust force and torque of drilling process rises with the feed rate. The lower spindle speed resulted in the greater amount of thrust. Feed rates have greater influence on the thrust force than the spindle speed. The combination of greater feed rate and lower spindle speed results in the maximum amount of thrust. However, combination of greater feed rate and spindle speed resulted in maximum amount of torque.

Effects of cutting temperature and process optimization in drilling of GFRP composites

2020 ◽  
Vol 55 (2) ◽  
pp. 235-249
Author(s):  
A Tamer Erturk ◽  
Fahri Vatansever ◽  
Eser Yarar ◽  
E Asım Guven ◽  
Tamer Sinmazcelik
Keyword(s):  
Feed Rate ◽  
Cutting Temperature ◽  
Spindle Speed ◽  
Glass Fiber Reinforced ◽  
Drill Bits ◽  
Drilling Parameters ◽  
Tool Coating ◽  
Composite Interface ◽  
Composite Drilling ◽  
Push Out

The present work deals with temperature effects and parametric optimization in the drilling of continuous glass fiber reinforced epoxy composite. Drilling ability was examined operating a drilling system with different drill bits, feed rate, and spindle speed parameters. The investigation was performed by changing the tool and composite interface. Drilling experiments were carried out under the dry condition. Thrust force and drilling temperatures were measured using dynamometer and thermal camera. Peel-up and push-out delamination were evaluated using an image analyzing tool. Results show that the tribo-mechanical behavior of the drilling operation is affected at different levels by tool coating. This behavior is related to the intrinsic friction properties of coating nature. Response surface methodology was used in the evaluation of experiment results. The feed rate of 0.13 mm/rev, spindle speed of 2425 rpm and HSS-TiN drill bit are found as an optimum drilling parameters and drill type.

Surface Roughness Analysis of Carbon/Glass Hybrid Polymer Composites in Drilling Process Based on Taguchi and Response Surface Methodology

2015 ◽  
Vol 1119 ◽  
pp. 622-627 ◽  
Author(s):  
Chye Lih Tan ◽  
Azwan Iskandar Azmi ◽  
Noorhafiza Muhammad
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Regression Model ◽  
Response Surface ◽  
Feed Rate ◽  
Hybrid Composite ◽  
Spindle Speed ◽  
Tool Geometry ◽  
Secondary Process ◽  
Drilling Process

Drilling is an essential secondary process for near net-shape of hybrid composite as to achieve the required dimensional tolerances prior to final application. Dimensional tolerance is often influenced by the surface integrity or surface roughness of the workpart. Thus, this paper aims to employ the Taguchi and response surface methodologies in minimizing the surface roughness of drilled carbon-glass hybrid fibre reinforced polymer (CGCG) using tungsten carbide, K20 drill bits. The effects of spindle speed, feed rate and tool geometry on surface roughness were evaluated and optimum cutting conditions for minimizing the aforementioned response was determined. Subsequently, response surface methodology (RSM) was utilised in finding the empirical relationships between experimental parameters and surface roughness based on the Taguchi results. The experimental analyses reveal that surface roughness is greatly influenced by feed rate and tool geometry rather than the spindle speed. This is due to the increment of feed that attributed to the increased strain rate and hence, deteriorated the surface roughness of the hybrid composite. The predicted results (via regression model) and theoretical results (via additivity law) were in good agreement with experiment results. This indicates that the regression model from response surface methodology (RSM) can be used to predict the surface roughness in machining of CGCG hybrid composite.

scholarly journals Effect of Cutting Parameter on Material Removal Rate and Surface Roughness in Deep Drilling Process

2016 ◽  
Vol 2 (5) ◽  
Author(s):  
Mostafa A. Abdullah  , Ahmed B. Abdulwahhab   ,   Atheer R.
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Spindle Speed ◽  
Cutting Conditions ◽  
Drilling Process ◽  
Tool Diameter ◽  
Twist Drills

In the curents study aimed to assess the effects of cutting conditions  (spindle speed, feed rate, tool diameter) parameters as input impact on material removal rate (MRR) and surface roughness (Ra) as output of steel (AISI 1015). A number of drilling experiments were conducted using the L9 orthogonal array on conventional drilling machine with use feed rate (0.038,0.076,0.203) mm/rev and spindle speed (132,550,930) rpm and tool diameter (11,15,20) mm HSS twist drills under dry cutting conditions. Analysis of variance (ANOVA) was employed to determine the most significant control factors affecting on surface roughness and MRR. The result shown the tool diameter the important factor effect with (64.08%) and (76.12%) on MRR and surface roughness respectively.

Sign in / Sign up

Export Citation Format

Share Document