In vitro characterisation of ultrasound-induced heating effects in the mother and fetus: A clinical perspective

Ultrasound ◽  
2020 ◽  
pp. 1742271X2095319
Author(s):  
Stephanie F Smith ◽  
Piero Miloro ◽  
Richard Axell ◽  
Gail ter Haar ◽  
Christoph Lees
Keyword(s):  
Temperature Increase ◽  
Skin Surface ◽  
Maximum Temperature ◽  
Factors Affecting ◽  
Bone Interface ◽  
Heating Effects ◽  
Power Setting ◽  
Lower Temperature

Introduction The quantification of heating effects during exposure to ultrasound is usually based on laboratory experiments in water and is assessed using extrapolated parameters such as the thermal index. In our study, we have measured the temperature increase directly in a simulator of the maternal–fetal environment, the ‘ISUOG Phantom’, using clinically relevant ultrasound scanners, transducers and exposure conditions. Methods The study was carried out using an instrumented phantom designed to represent the pregnant maternal abdomen and which enabled temperature recordings at positions in tissue mimics which represented the skin surface, sub-surface, amniotic fluid and fetal bone interface. We tested four different transducers on a commercial diagnostic scanner. The effects of scan duration, presence of a circulating fluid, pre-set and power were recorded. Results The highest temperature increase was always at the transducer–skin interface, where temperature increases between 1.4°C and 9.5°C were observed; lower temperature rises, between 0.1°C and 1.0°C, were observed deeper in tissue and at the bone interface. Doppler modes generated the highest temperature increases. Most of the heating occurred in the first 3 minutes of exposure, with the presence of a circulating fluid having a limited effect. The power setting affected the maximum temperature increase proportionally, with peak temperature increasing from 4.3°C to 6.7°C when power was increased from 63% to 100%. Conclusions Although this phantom provides a crude mimic of the in vivo conditions, the overall results showed good repeatability and agreement with previously published experiments. All studies showed that the temperature rises observed fell within the recommendations of international regulatory bodies. However, it is important that the operator should be aware of factors affecting the temperature increase.

scholarly journals Silver Nanoparticles and Their Antibacterial Applications

2021 ◽  
Vol 22 (13) ◽  
pp. 7202
Author(s):  
Tamara Bruna ◽  
Francisca Maldonado-Bravo ◽  
Paul Jara ◽  
Nelson Caro
Keyword(s):  
Silver Nanoparticles ◽  
Antibacterial Agents ◽  
Multidrug Resistant ◽  
Secondary Effects ◽  
Cytotoxic Effects ◽  
Factors Affecting ◽  
Gram Positive Bacteria ◽  
Resistant Strains

Silver nanoparticles (AgNPs) have been imposed as an excellent antimicrobial agent being able to combat bacteria in vitro and in vivo causing infections. The antibacterial capacity of AgNPs covers Gram-negative and Gram-positive bacteria, including multidrug resistant strains. AgNPs exhibit multiple and simultaneous mechanisms of action and in combination with antibacterial agents as organic compounds or antibiotics it has shown synergistic effect against pathogens bacteria such as Escherichia coli and Staphylococcus aureus. The characteristics of silver nanoparticles make them suitable for their application in medical and healthcare products where they may treat infections or prevent them efficiently. With the urgent need for new efficient antibacterial agents, this review aims to establish factors affecting antibacterial and cytotoxic effects of silver nanoparticles, as well as to expose the advantages of using AgNPs as new antibacterial agents in combination with antibiotic, which will reduce the dosage needed and prevent secondary effects associated to both.

Factors affecting in vitro and in vivo antioxidant effects. Experimental conditions and nature of oxidants determine antioxidant efficacy

2021 ◽  
pp. 1-9
Author(s):  
Etsuo Niki
Keyword(s):  
Biological Molecules ◽  
Experimental Conditions ◽  
Factors Affecting ◽  
Beneficial Effects ◽  
Multiple Oxidants ◽  
Antioxidant Effects

Reactive oxygen and nitrogen species have been implicated in the onset and progression of various diseases and the role of antioxidants in the maintenance of health and prevention of diseases has received much attention. The action and effect of antioxidants have been studied extensively under different reaction conditions in multiple media. The antioxidant effects are determined by many factors. This review aims to discuss several important issues that should be considered for determination of experimental conditions and interpretation of experimental results in order to understand the beneficial effects and limit of antioxidants against detrimental oxidation of biological molecules. Emphasis was laid on cell culture experiments and effects of diversity of multiple oxidants on antioxidant efficacy.

Maturation, iron deficiency, and ligands in enteric radioiron transport in vitro

1963 ◽  
Vol 204 (1) ◽  
pp. 171-175 ◽  
Author(s):  
W. S. Ruliffson ◽  
J. M. Hopping
Keyword(s):  
Ascorbic Acid ◽  
Iron Deficiency ◽  
Iron Absorption ◽  
Deficiency Anemia ◽  
Anaerobic Incubation ◽  
Reverse Effect ◽  
Factors Affecting ◽  
Everted Gut Sac

The effects in rats, of age, iron-deficiency anemia, and ascorbic acid, citrate, fluoride, and ethylenediaminetetraacetate (EDTA) on enteric radioiron transport were studied in vitro by an everted gut-sac technique. Sacs from young animals transported more than those from older ones. Proximal jejunal sacs from anemic animals transported more than similar sacs from nonanemic rats, but the reverse effect appeared in sacs formed from proximal duodenum. When added to media containing ascorbic acid or citrate, fluoride depressed transport as did anaerobic incubation in the presence of ascorbic acid. Anaerobic incubation in the presence of EDTA appeared to permit elevated transport. Ascorbic acid, citrate, and EDTA all enhanced the level of Fe59 appearing in serosal media. These results appear to agree with previously established in vivo phenomena and tend to validate the in vitro method as one of promise for further studies of factors affecting iron absorption and of the mechanism of iron absorption.

Factors affecting the time of formation of the mouse blastocoele

Development ◽  
1977 ◽  
Vol 41 (1) ◽  
pp. 79-92
Author(s):  
Rosita Smith ◽  
Anne McLaren
Keyword(s):  
Cytochalasin B ◽  
Critical Factor ◽  
Cell Number ◽  
Experimental Manipulation ◽  
Factors Affecting ◽  
Elapsed Time ◽  
Developmental Age ◽  
Culture Formation

In normal mouse embryos developing in vivo, the first appearance of the blastocyst cavity was found to be associated more closely with developmental age, judged by cell number, than with chronological age, i.e. elapsed time since ovulation. When development was slowed by in vitro culture, formation of the blastocoele was delayed. However, cell number itself was not a critical factor, since the number of cells per embryo could be doubled or tripled or halved by experimental manipulation without substantially affecting the timing of blastocoele formation. Experiments in which one cell division was suppressed with cytochalasin-B, leading to tetraploidy, showed that the number of cell divisions since fertilization was also not critical. A possible role is suggested either for nucleocytoplasmic ratio, or for the number of nuclear or chromosomal divisions or DNA replications since fertilization, all of which increase during cleavage.

Acoustic Signals from Skeletal Muscle

Physiology ◽  
1990 ◽  
Vol 5 (1) ◽  
pp. 17-21 ◽  
Author(s):  
DT Barry
Keyword(s):  
Skeletal Muscles ◽  
Acoustic Signals ◽  
Skin Surface ◽  
Pressure Waves ◽  
Mechanical Vibrations ◽  
Intrinsic Component ◽  
Measuring Force ◽  
Muscle Sounds

Contracting skeletal muscles emit pressure waves that are audible at the skin surface and are easily recorded with standard microphones both in vivo and in vitro. These muscle sounds are an intrinsic component of the contractile mechanism and are produced by mechanical vibrations at the resonant frequency of the muscle. The sounds are useful in measuring force, fatigue, and mechanical properties of muscle.

scholarly journals Assessment of Effects of Laser Light Combining Three Wavelengths (450, 520 and 640 nm) on Temperature Increase and Depth of Tissue Lesions in an Ex Vivo Study

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5340
Author(s):  
Kamil Jurczyszyn ◽  
Witold Trzeciakowski ◽  
Zdzisław Woźniak ◽  
Piotr Ziółkowski ◽  
Mateusz Trafalski
Keyword(s):  
Duty Cycle ◽  
Temperature Increase ◽  
Ex Vivo ◽  
Visible Spectrum ◽  
Maximum Temperature ◽  
Lesion Depth ◽  
Single Beam ◽  
Duty Cycles ◽  
Rate Of Increase

Background: Lasers are widely used in medicine in soft and hard tissue surgeries and biostimulation. Studies found in literature typically compare the effects of single-wavelength lasers on tissues or cell cultures. In our study, we used a diode laser capable of emitting three components of visible light (640 nm, red; 520 nm, green; 450 nm, blue) and combining them in a single beam. The aim of the study was to assess the effects of laser radiation in the visible spectrum on tissue in vitro, depending on the wavelength and pulse width. Methods: All irradiations were performed using the same output power (1.5 W). We used various duty cycles: 10, 50, 80 and 100% with 100 Hz frequency. Maximum superficial temperature, rate of temperature increase and lesion depth were investigated. Results: Maximum superficial temperature was observed for 450 + 520 nm irradiation (100% duty cycle). The highest rate of increase of temperature was noted for 450 + 520 nm (100% duty cycle). Maximum lesion depth was observed in case of three-wavelength irradiation (450 + 520 + 640 nm) for 100, 80 and 50% duty cycles. Conclusions: The synergistic effect of two-wavelength (450 + 520 nm) irradiation was observed in case of maximum temperature measurement. The deepest depth of lesion was noted after three-wavelength irradiation (450 + 520 + 640 nm).

scholarly journals Osseointegration of Antimicrobial Acrylic Bone Cements Modified with Graphene Oxide and Chitosan

2020 ◽  
Vol 10 (18) ◽  
pp. 6528 ◽  
Author(s):  
Mayra Eliana Valencia Zapata ◽  
José Herminsul Mina Hernandez ◽  
Carlos David Grande Tovar ◽  
Carlos Humberto Valencia Llano ◽  
Blanca Vázquez-Lasa ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Bone Cement ◽  
Orthopedic Surgery ◽  
Bending Strength ◽  
Orthopedic Implants ◽  
Parietal Bone ◽  
Maximum Temperature ◽  
Cement Interface

Acrylic bone cement (ABC) is one of the most used materials in orthopedic surgery, mainly for the fixation of orthopedic implants to the bone. However, ABCs usually present lack of biological activity and osseointegration capacity that leads to loosening of the prosthesis. This work reports the effect of introducing graphene oxide (GO) and chitosan (CS), separately or together, in the ABC formulation on setting performance, mechanical behavior, and biological properties. Introduction of both CS and GO to the ABC decreased the maximum temperature by 21% and increased the antibacterial activity against Escherichia coli by 87%, while introduction of only CS decreased bending strength by 32%. The results of cell viability and cell adhesion tests showed in vitro biocompatibility. The in vivo response was investigated using both subdermal and bone parietal implantations in Wistar rats. Modified ABCs showed absence of immune response, as confirmed by a normal inflammatory response in Wistar rat subdermal implantation. The results of the parietal bone implantation showed that the addition of CS and GO together allowed a near total healing bone–cement interface, as observed in the micrographic analysis. The overall results support the great potential of the modified ABCs for application in orthopedic surgery mainly in those cases where osseointegration is required.

scholarly journals Safety Assessment and Biological Effects of a New Cold Processed SilEmulsion for Dermatological Purpose

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Sara Raposo ◽  
Ana Salgado ◽  
Lídia Gonçalves ◽  
Pedro C. Pinto ◽  
Manuela Urbano ◽  
...  
Keyword(s):  
Safety Assessment ◽  
Biological Effects ◽  
Response Assessment ◽  
Skin Surface ◽  
Patch Tests ◽  
Hazard Exposure ◽  
Margin Of Safety ◽  
Skin Surface Lipids

It is of crucial importance to evaluate the safety profile of the ingredients used in dermatological emulsions. A suitable equilibrium between safety and efficacy is a pivotal concern before the marketing of a dermatological product. The aim was to assess the safety and biological effects of a new cold processed silicone-based emulsion (SilEmulsion). The hazard, exposure, and dose-response assessment were used to characterize the risk for each ingredient. EpiSkin assay and human repeat insult patch tests were performed to compare the theoretical safety assessment toin vitroandin vivodata. The efficacy of the SilEmulsion was studied using biophysical measurements in human volunteers during 21 days. According to the safety assessment of the ingredients, 1,5-pentanediol was an ingredient of special concern since its margin of safety was below the threshold of 100 (36.53). EpiSkin assay showed that the tissue viability after the application of the SilEmulsion was 92 ± 6% and, thus considered nonirritant to the skin. The human studies confirmed that the SilEmulsion was not a skin irritant and did not induce any sensitization on the volunteers, being safe for human use. Moreover, biological effects demonstrated that the SilEmulsion increased both the skin hydration and skin surface lipids.

Hyperglycemic athymic nude mice: factors affecting in vitro insulin secretion

1992 ◽  
Vol 263 (6) ◽  
pp. E1131-E1133
Author(s):  
A. Zeidler ◽  
P. Edwards ◽  
J. Goldman ◽  
S. Kort ◽  
W. P. Meehan ◽  
...  
Keyword(s):  
Animal Model ◽  
Insulin Secretion ◽  
Insulin Dependent Diabetes Mellitus ◽  
Dependent Diabetes Mellitus ◽  
Factors Affecting ◽  
In Vitro Insulin Secretion ◽  
Insulin Secretion In Vitro ◽  
And Control

The strain of athymic nude male mice (ANM) developed at the University of Southern California (USC) exhibits spontaneous hyperglycemia and relative hypoinsulinemia in vivo. To investigate factors that influence insulin secretion in this animal model of non-insulin-dependent diabetes mellitus, we utilized the isolated perfused mouse pancreas of the ANM-USC and control BALB/c mice. We compared in vitro glucose-induced insulin secretion in ANM-USC and control mice, inhibition of secretion by somatostatin, and variability of insulin secretion over the two-year period it took to complete these experiments. Glucose-induced insulin secretion from the isolated pancreas was biphasic in both ANM-USC and controls. Insulin secretion was quantitatively equal to or greater than control mice, depending on the phase of secretion analyzed and the source of the control mice. In contrast to pancreases of control mice, insulin secretion from ANM-USC pancreases was relatively resistant to inhibition of insulin secretion by somatostatin. Variability in insulin secretion over the two years in which these experiments were performed was greater from pancreases of control than that observed from pancreases of the ANM-USC. The hyperglycemic ANM-USC mouse does not demonstrate diminished insulin secretion in vitro yet is relatively hypoinsulinemic in vivo. Thus circulating factors other than somatostatin might contribute to the insulinopenic stage in this animal model.

Sign in / Sign up

Export Citation Format

Share Document