Impact of energy efficiency on computer numerically controlled machining

2009 ◽  
Vol 224 (4) ◽  
pp. 531-541 ◽  
Author(s):  
S E Anderberg ◽  
S Kara ◽  
T Beno
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Environmental Performance ◽  
Cost Efficiency ◽  
Energy Savings ◽  
Cost Model ◽  
Machining Parameters ◽  
Computer Numerically Controlled ◽  
The Relationship ◽  
Environmental Demands

Increasing environmental demands from governmental bodies and customers stress the importance of companies improving their environmental performance. The research presented here shows that productivity and cost efficiency improvements can be achieved alongside energy savings in a computer numerically controlled machining environment. This improves the profitability of the companies, but also leads them towards more sustainable and environmentally aware manufacturing; the relationship between machining parameters, machining costs, and energy consumption is evaluated. From this perspective, it is important that production planners etc. understand the methodological possibilities for improvements in cost and energy efficiency. The current research is based on a machining cost model and experiments where energy consumption and tool wear were monitored.

scholarly journals Improving the economic performances of the beet-sugar industry

2008 ◽  
pp. 55-61 ◽  
Author(s):  
Bojana Prodanic ◽  
Aleksandar Jokic ◽  
Jelena Markovic ◽  
Zoltan Zavargo
Keyword(s):  
European Union ◽  
Energy Efficiency ◽  
Energy Consumption ◽  
Energy Savings ◽  
General Trend ◽  
Sugar Industry ◽  
Regional Level ◽  
Efficiency Improvement ◽  
Considerable Saving ◽  
Energy Efficiency Improvement

General trend of free trade at the regional level as well as in the direction of European Union has motivated sugar factories located in Serbia to invest into technologies that are more efficient in order to make their products more competitive in the markets of Europe. Until 2005, the project of energy efficiency improvement in Serbian sugar factories was conducted in Crvenka and Zabalj. Now, they have energy consumption around 1 MJ/kg beet, in contrast to the previous consumption of 1.2 up to 1.5 MJ/kg beet. Further improvements are possible but investments would be high. A result of measurements taken during 2006, after the sugar factory "Donji Srem" - Pecinci was reconstructed showed that a considerable saving has been achieved. The first set of measurements showed that the energy consumption was 1.01 MJ/kg beet, which was 20% higher than intended, but at the same time energy savings were about 30% lower with respect to the values before the reconstruction.

scholarly journals Enhancing energy efficiency of an existing housing stock

2021 ◽  
Vol 2 (47) ◽  
pp. 3-10
Author(s):  
K.V. Izmaylova ◽  
L.A. Kharchenko
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
User Behavior ◽  
Housing Stock ◽  
Cost Model ◽  
Positive Trend ◽  
Improve Energy Efficiency ◽  
Operation Period ◽  
Existing Housing ◽  
Full Operation

The article analyzes domestic and international experience in the field of energy efficiency and energy security. Thus, it was important to adopt the Law of Ukraine "On the Energy Efficiency of Buildings", which introduced mandatory certification of buildings by energy consumption classes. The study of sources on the issues of effective energy consumption showed that issues related to improving the energy efficiency of buildings and structures are acquiring special relevance; the use of foreign models to improve the energy efficiency of the housing stock. Specific organizational and economic measures are highlighted that will help improve the energy efficiency of the national economy. The Swedish experience of using a modern cost model for the full period of operation ("General Concept") is studied, which aims to assess the economic results of investments in measures to improve the energy efficiency of the housing stock. The main principles of the modern cost model of the full operation period and the criteria for determining the number of necessary energy efficiency measures are considered. Analyzed "hard" (physical condition of the building) and "soft" (user behavior) measures that provide for the integrated energy efficiency of the building. The stages of the analysis according to the cost model of the full operation period are considered. The typical for Sweden ranges of the duration of energy efficient measures and the requirements for the internal rate of return, which depends on the general economic situation in the country and the terms of the loan, have been investigated.  Based on the results of the energy audit of the ten-story building selected for the study and taking into account the experience of Sweden, a number of measures to improve energy efficiency are proposed and a calculation is given to ensure the energy efficiency of a residential building in Ukraine. Based on the results obtained, it can be concluded that there is a positive trend in this implementation. With the integrated use of all measures that will even allow you to save more, you can significantly improve the energy efficiency of the existing housing stock in Ukraine.

scholarly journals Optimization of Energy Efficiency, Operation Costs, Carbon Footprint and Ecological Footprint with Reverse Osmosis Membranes in Seawater Desalination Plants

Membranes ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 781
Author(s):  
Federico Leon ◽  
Alejandro Ramos ◽  
S. Ovidio Perez-Baez
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Reverse Osmosis ◽  
Ecological Footprint ◽  
Energy Savings ◽  
Seawater Desalination ◽  
Operation Costs ◽  
Private And Public ◽  
Desalination Plants ◽  
Reverse Osmosis Membranes

This article shows the optimization of the reverse osmosis process in seawater desalination plants, taking the example of the Canary Islands, where there are more than 320 units of different sizes, both private and public. The objective is to improve the energy efficiency of the system in order to save on operation costs as well as reduce the carbon and ecological footprints. Reverse osmosis membranes with higher surface area have lower energy consumption, as well as energy recovery systems to recover the brine pressure and introduce it in the system. Accounting for the operation, maintenance and handling of the membranes is also important in energy savings, in order to improve the energy efficiency. The energy consumption depends on the permeate water quality required and the model of the reverse osmosis membrane installed in the seawater desalination plant, as it is shown in this study.

scholarly journals A Study on Energy and Cost Efficiency for Existing Hotel Buildings in Turkey

2019 ◽  
Vol 111 ◽  
pp. 03037
Author(s):  
Merve Atmaca ◽  
Zerrin Yýlmaz
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Cost Efficiency ◽  
Building Energy ◽  
Energy Performance ◽  
Insulation Material ◽  
Negative Effects ◽  
Energy Needs ◽  
Global Cost ◽  
Optimum Solution

In Turkey, according to TUİK Sectoral Energy Consumption Statistics (2006), the hotel buildings with the highest share, constitute 35% of the total building energy consumption. Energy needs and consumption behaviours differ according to the typology of the building. Energy Performance of Buildings Directive (EPBD) has been adapted to the conditions of Turkey to increase energy and cost efficiency, to reduce the environmental and economic negative effects. The energy consumption and the global cost were investigated under different conditions in an existing hotel building. The paper is unique in its ability to deliver optimum solution through comparison by evaluating energy and cost efficiency at the same time considering sectoral, climatic, technological and economic national conditions when the literature research detailed in the present works about the problem is evaluated in detail. All findings have been compared simultaneously under different climate regions of seasonal and yearly working conditions of selected test hotel to obtain the energy and cost efficiency. Among the proposed improvement scenarios, the optimum scenario is determined in terms of cost and energy efficiency in S18 which has the highest energy efficiency. In this case, both insulation material type and thickness as well as glass type can be bent and through multiple measures can be achieved by 25.7% improvement for energy efficiency.

E|Benchmark - Approaches and Methods for Assessing the Energy Efficiency of the Industrial Automated Product Manufacturing

2014 ◽  
Vol 655 ◽  
pp. 15-20 ◽  
Author(s):  
Sven Kreitlein ◽  
Tobias Rackow ◽  
Jörg Franke
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Energy Savings ◽  
Value Systems ◽  
Course Of Action ◽  
Product Manufacturing ◽  
Actual Energy Consumption ◽  
Related Characteristic ◽  
Industry Comparison ◽  
Successive Calculation

This paper introduces a method for the assessment and evaluation of energy efficiency of the manufacturing processes in the production as well as a corporate and cross-industry comparison. Already today, energy-related characteristic value systems are used, which are related to the energy consumption of large electronic household appliances or are focusing on their production facilities. The energy efficiency value is a newly developed indicator and will provide valuable information about the energy efficiency of the production of various products, production operators, and consumers. In the following, the energy efficiency value, which is based on the approach of minimal value calculation, is presented in detail. The basic idea is the comparison and evaluation of energy efficiency based on the ratio of the theoretically required energy consumption to the actual energy consumption. Depending on the analysis of influencing factors, a model highlighting their dependencies could be established. The developed system hinges on a successive calculation of the minimum value. Each of these minimum types can be put in relation to the measured energy consumption. However, depending on the chosen basis, the conclusion and focus of the calculated key figure may vary. By using the real minimum as a basis, the actually existing energy savings become visible. The method will be put to the test through an exemplary application for processes in the fields of cutting technologies. This course of action allows for the validation of the developed energy efficiency value and reveals the potential of this method.

Research on Energy Efficiency and Environmental Pollution in China: a Simultaneous Equations Approach

2011 ◽  
Vol 361-363 ◽  
pp. 974-977 ◽  
Author(s):  
Ying Nan Dong ◽  
Yu Duo Lu ◽  
Jiao Jiao Yu
Keyword(s):  
Energy Efficiency ◽  
Sustainable Development ◽  
Energy Consumption ◽  
Environmental Pollution ◽  
Energy Intensity ◽  
Industrial Structure ◽  
Economic Loss ◽  
Simultaneous Equations ◽  
Consumption Structure ◽  
The Relationship

This paper examined the relationship between the energy efficiency and the environmental pollution. By using the data of energy intensity and economic loss caused by environmental pollution (ELP) in China from 1989-2009, a simultaneous equations was developed. The result of two-stage OLS estimation suggested that the energy had exerted positive influences on the decreasing of the environmental pollutions. By enhancing the energy efficiency and adjusting the industrial structure and energy consumption structure, China is exploring a road for sustainable development in the energy conservation.

Influence of Volumetric Capacity on Energy Consumption in Oil-Lubricated Compressed Air Systems

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Pawel Olszewski ◽  
Claus Borgnakke
Keyword(s):  
Mathematical Model ◽  
Energy Efficiency ◽  
Energy Consumption ◽  
Potential Energy ◽  
Uncertainty Analysis ◽  
Control Strategy ◽  
Energy Savings ◽  
Compressed Air ◽  
Numerical Code ◽  
Volumetric Capacity

The aim of this research is to estimate the influence of compressed air volumetric capacity on the energy consumption in systems equipped with oil-lubricated screw compressors. A mathematical model of oil-lubricated screw compressors has been proposed. The model is verified by comparing with real measurements, and overall uncertainty analysis is estimated. An in-house developed numerical code (c++) is used to calculate the energy consumption in 252,000 combinations. The final result can be used to estimate the energy efficiency of existing air systems and to assess potential energy savings due to changes in the operation of the system and its control strategy.

scholarly journals Lighting Control Including Daylight and Energy Efficiency Improvements Analysis

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2166 ◽  
Author(s):  
Aniela Kaminska ◽  
Andrzej Ożadowicz
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Energy Savings ◽  
Residential Buildings ◽  
Experimental Tests ◽  
Experimental Results ◽  
Automation System ◽  
Building Automation ◽  
Total Energy Consumption ◽  
Lighting Control

Energy used for lighting is one of the major components of total energy consumption in buildings. Nowadays, buildings have a great potential to reduce their energy consumption, but to achieve this purpose additional efforts are indispensable. In this study, the need for energy savings evaluation before the implementation of lighting control algorithms for a specified building is highlighted. Therefore, experimental tests have been carried out in a university building with laboratories and other rooms, equipped with KNX building automation system. A dimmable control strategy has been investigated, dependent on daylight illuminance. Moreover, a relationship between external and internal daylight illuminance levels has been evaluated as well. Based on the experimental results, the authors proposed a method for the rough estimation of electrical energy savings. Since, according to the EN 15232 standard, Building Automation and Control Systems (BACS) play an important role in buildings’ energy efficiency improvements, the BACS efficiency factors from this standard have been used to verify the experimental results presented in the paper. The potential to reduce energy consumption from lighting in non-residential buildings by 28% for offices and 24% for educational buildings has been confirmed, but its dependence on specific building parameters has been discussed as well.

scholarly journals Measuring Energy Efficiency and Environmental Performance: A Case of South Asia

Processes ◽  
2019 ◽  
Vol 7 (6) ◽  
pp. 325 ◽  
Author(s):  
Yumei Hou ◽  
Wasim Iqbal ◽  
Ghulam Muhammad Shaikh ◽  
Nadeem Iqbal ◽  
Yasir Ahmad Solangi ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Renewable Energy ◽  
Energy Consumption ◽  
South Asia ◽  
Environmental Performance ◽  
Carbon Emission ◽  
Consumption Ratio ◽  
Environmental Performance Index ◽  
Emission Index ◽  
Ratio Energy

When assessing energy efficiency, most studies have frequently ignored environmental aspects even though the concept has been widely used in the past. This study evaluates the energy efficiency and environmental performance of South Asia by using DEA (data envelopment analysis) like mathematical composite indicator. We construct a comprehensive set of indicators, including an energy self-sufficiency ratio, energy production over consumption ratio, energy imports, diversification index of energy imports, energy reserve ratio, GDP productivity, energy intensity, per capita energy consumption index, carbon emission index, carbon emission index per unit of energy consumption and share of renewable energy in order to develop an energy efficiency and environmental performance index. Unlike other studies, this study first examines each indicator and then estimates a combined score for each country. The results reveal that Bhutan as a more secure country and Pakistan showed a decreasing trend, while Sri Lanka and India performed satisfactorily. Remarkably, Bangladesh, Nepal and Afghanistan showed a decreasing trend. This study proposes a policy that increases the cross-border trade of renewable energy for long term energy efficiency and environmental performance.

Investigating energy consumption and economic growth for BRICS-T countries

2019 ◽  
Vol 16 (4) ◽  
pp. 184-195 ◽  
Author(s):  
Durmuş Çağrı Yıldırım ◽  
Seda Yıldırım ◽  
Isıl Demirtas
Keyword(s):  
Economic Growth ◽  
Energy Consumption ◽  
Energy Savings ◽  
Panel Cointegration ◽  
Cointegration Test ◽  
Real Output ◽  
Content Type ◽  
Natural Logarithm ◽  
Panel Cointegration Test ◽  
The Relationship

Purpose The purpose of this paper is to explore the relationship between energy consumption and economic growth for Brazil, Russia, China, India, South Africa and Turkey (BRICS-T) countries. In this context, this study investigates energy consumption and real output in BRICS-T countries through panel cointegration. Design/methodology/approach The data include energy consumption and real output for BRICS-T countries and period of 1990–2014. The variables are transformed into natural logarithm. To analyze these data, this study employed Pedroni cointegration test, the second-generation panel cointegration test, Westerlund and Edgerton (2008) test and FMOLS test. Findings Results indicate that there is a bi-directional causality relationship between energy consumption and economic growth for BRICS-T countries. An increase in GDP leads to an increase in energy consumption and an increase in energy consumption leads to an increase in GDP. Research limitations/implications This study used data that include the period of 1990–2014 for BRICS-T countries. So, further studies can use different periods of data or different countries. Originality/value This study provides important evidence that countries with strong growth performance need to follow bi-directional energy policies to increase both energy investments and ensure energy savings.

Sign in / Sign up

Export Citation Format

Share Document