scholarly journals Different fixation pattern for thoracolumbar fracture of ankylosing spondylitis: A finite element analysis

PLoS ONE ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. e0250009
Author(s):  
Tianyu Zhang ◽  
Yanhua Wang ◽  
Peixun Zhang ◽  
Feng Xue ◽  
Dianying Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Ankylosing Spondylitis ◽  
Internal Fixation ◽  
Thoracolumbar Fracture ◽  
Von Mises Stress ◽  
Fe Model ◽  
Pull Force ◽  
Kyphosis Correction ◽  
Four Levels ◽  
Von Mises

The objective of this study is to establish an ankylosing spondylitis (AS) thoracolumbar fracture finite element (FE) model and provide a proper posterior fixation choice from the biomechanical perspective. The ankylosing spondylitis T9-L5 FE model was built and the range of motion (ROM) was compared to previous studies. The L1 transverse fracture was simulated and was separately fixed by five different patterns. The pull force and yielding force of the screws, the von Mises stress of the internal fixation, and the displacement of fracture site were analyzed to evaluate the proper fixation pattern for thoracolumbar fracture of AS. ROM of AS model was obviously restricted comparing to the normal vertebral experimental data. All the fixation patterns can stabilize the fracture. At least four levels of fixation can reduce the von Mises stress of the internal fixation. Four levels fixation has a higher pull force than the six levels fixation. Skipped level fixation did not reduce the stress, pull force and yielding force. The kyphosis correction did not change the biomechanical load. At least 4 levels fixation was needed for AS thoracolumbar fracture. The cemented screws should be chosen in 4 levels fixation to increase the holding of the screws. The skipped fixation has no advantage. The kyphosis correction can be chosen after weighing the pros and cons.

scholarly journals A Novel Rat Model of Orthodontic Tooth Movement Using Temporary Skeletal Anchorage Devices: 3D Finite Element Analysis andIn VivoValidation

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Neelambar Kaipatur ◽  
Yuchin Wu ◽  
Samer Adeeb ◽  
Thomas Stevenson ◽  
Paul Major ◽  
...  
Keyword(s):  
Finite Element ◽  
Alveolar Bone ◽  
Tooth Movement ◽  
Orthodontic Tooth Movement ◽  
Von Mises Stress ◽  
Fe Model ◽  
Sprague Dawley ◽  
Element Analysis ◽  
Von Mises ◽  
The Right

The aim of this animal study was to develop a model of orthodontic tooth movement using a microimplant as a TSAD in rodents. A finite element model of the TSAD in alveolar bone was built usingμCT images of rat maxilla to determine the von Mises stresses and displacement in the alveolar bone surrounding the TSAD. Forin vivovalidation of the FE model, Sprague-Dawley rats (n=25) were used and a Stryker 1.2 × 3 mm microimplant was inserted in the right maxilla and used to protract the right first permanent molar using a NiTi closed coil spring. Tooth movement measurements were taken at baseline, 4 and 8 weeks. At 8 weeks, animals were euthanized and tissues were analyzed by histology and EPMA. FE modeling showed maximum von Mises stress of 45 Mpa near the apex of TSAD but the average von Mises stress was under 25 Mpa. Appreciable tooth movement of 0.62 ± 0.04 mm at 4 weeks and 1.99 ± 0.14 mm at 8 weeks was obtained. Histological and EPMA results demonstrated no active bone remodeling around the TSAD at 8 weeks depicting good secondary stability. This study provided evidence that protracted tooth movement is achieved in small animals using TSADs.

scholarly journals Identification of Surgical Plan for Syndesmotic Fixation Procedure Based on Finite Element Method

2020 ◽  
Vol 10 (12) ◽  
pp. 4349 ◽  
Author(s):  
Tae Sik Goh ◽  
Beop-Yong Lim ◽  
Jung Sub Lee ◽  
Chi-Seung Lee
Keyword(s):  
Finite Element ◽  
Simulation Method ◽  
Fe Analysis ◽  
Von Mises Stress ◽  
Fe Model ◽  
Syndesmotic Screw ◽  
Surgical Options ◽  
Biomechanical Parameters ◽  
Von Mises ◽  
Two Parameters

Syndesmosis injuries account for approximately 20% of ankle fractures that require surgery. Although multiple surgical options are available, all of them are based on metal screws. Serious complications that arise when applying metal screws include screw loosening or breakage. To prevent such complications, we applied a simulation method using a finite element (FE) analysis. We created a 3D FE model of an ankle joint and conducted an FE analysis focusing on syndesmosis in terms of the level, material, and diameter of the syndesmotic screw and the number of penetrated cortical bones. The magnitude and direction of the force applied to the tibia in the midstance state were considered for simulating the model. The maximum von-Mises stress and syndesmosis widening were analyzed in terms of different biomechanical parameters. We identified the characteristics of the most biomechanically stable syndesmotic screw and its fixation point on the basis of the two parameters. We demonstrated that the ideal syndesmotic screw fixation should be fixed at a level 20 to 25 mm above the ankle using a 4.5 mm titanium screw.

scholarly journals Multi-layered bird beaks: a finite-element approach towards the role of keratin in stress dissipation

2012 ◽  
Vol 9 (73) ◽  
pp. 1787-1796 ◽  
Author(s):  
Joris Soons ◽  
Anthony Herrel ◽  
Annelies Genbrugge ◽  
Dominique Adriaens ◽  
Peter Aerts ◽  
...  
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Speckle Pattern ◽  
Young Modulus ◽  
Von Mises Stress ◽  
Fe Model ◽  
Element Approach ◽  
Von Mises ◽  
The Impact

Bird beaks are layered structures, which contain a bony core and an outer keratin layer. The elastic moduli of this bone and keratin were obtained in a previous study. However, the mechanical role and interaction of both materials in stress dissipation during seed crushing remain unknown. In this paper, a multi-layered finite-element (FE) model of the Java finch's upper beak ( Padda oryzivora ) is established. Validation measurements are conducted using in vivo bite forces and by comparing the displacements with those obtained by digital speckle pattern interferometry. Next, the Young modulus of bone and keratin in this FE model was optimized in order to obtain the smallest peak von Mises stress in the upper beak. To do so, we created a surrogate model, which also allows us to study the impact of changing material properties of both tissues on the peak stresses. The theoretically best values for both moduli in the Java finch are retrieved and correspond well with previous experimentally obtained values, suggesting that material properties are tuned to the mechanical demands imposed during seed crushing.

scholarly journals Development of a Finite Element Head Model for the Study of Impact Head Injury

2014 ◽  
Vol 2014 ◽  
pp. 1-14 ◽  
Author(s):  
Bin Yang ◽  
Kwong-Ming Tse ◽  
Ning Chen ◽  
Long-Bin Tan ◽  
Qing-Qian Zheng ◽  
...  
Keyword(s):  
Finite Element ◽  
Brain Injuries ◽  
Current Knowledge ◽  
Human Head ◽  
Von Mises Stress ◽  
Head Model ◽  
Fe Model ◽  
Prediction And Prevention ◽  
Von Mises ◽  
The Brain

This study is aimed at developing a high quality, validated finite element (FE) human head model for traumatic brain injuries (TBI) prediction and prevention during vehicle collisions. The geometry of the FE model was based on computed tomography (CT) and magnetic resonance imaging (MRI) scans of a volunteer close to the anthropometry of a 50th percentile male. The material and structural properties were selected based on a synthesis of current knowledge of the constitutive models for each tissue. The cerebrospinal fluid (CSF) was simulated explicitly as a hydrostatic fluid by using a surface-based fluid modeling method. The model was validated in the loading condition observed in frontal impact vehicle collision. These validations include the intracranial pressure (ICP), brain motion, impact force and intracranial acceleration response, maximum von Mises stress in the brain, and maximum principal stress in the skull. Overall results obtained in the validation indicated improved biofidelity relative to previous FE models, and the change in the maximum von Mises in the brain is mainly caused by the improvement of the CSF simulation. The model may be used for improving the current injury criteria of the brain and anthropometric test devices.

scholarly journals Effects of Revision Rod Position on Spinal Construct Stability in Lumbar Revision Surgery: A Finite Element Study

2022 ◽  
Vol 9 ◽  
Author(s):  
Quan-Chang Tan ◽  
Jin-Feng Huang ◽  
Hao Bai ◽  
Zi-Xuan Liu ◽  
Xin-Yi Huang ◽  
...  
Keyword(s):  
Finite Element ◽  
Revision Surgery ◽  
Spinal Instrumentation ◽  
Axial Rotation ◽  
Von Mises Stress ◽  
Fe Model ◽  
Interspinous Ligament ◽  
Moment Load ◽  
Von Mises ◽  
Changing Tendency

Revision surgery (RS) is a necessary surgical intervention in clinical practice to treat spinal instrumentation–related symptomatic complications. Three constructs with different configurations have been applied in RS. One distinguishing characteristic of these configurations is that the revision rods connecting previous segments and revision segments are placed alongside, outside, or inside the previous rods at the level of facetectomy. Whether the position of the revision rod could generate mechanical disparities in revision constructs is unknown. The objective of this study was to assess the influence of the revision rod position on the construct after RS. A validated spinal finite element (FE) model was developed to simulate RS after previous instrumented fusion using a modified dual-rod construct (DRCm), satellite-rod construct (SRC), and cortical bone trajectory construct (CBTC). Thereafter, maximum von Mises stress (VMS) on the annulus fibrosus and cages and the ligament force of the interspinous ligament, supraspinous ligament, and ligamentum flavum under a pure moment load and a follower load in six directions were applied to assess the influence of the revision rod position on the revision construct. An approximately identical overall reducing tendency of VMS was observed among the three constructs. The changing tendency of the maximum VMS on the cages placed at L4-L5 was nearly equal among the three constructs. However, the changing tendency of the maximum VMS on the cage placed at L2-L3 was notable, especially in the CBTC under right bending and left axial rotation. The overall changing tendency of the ligament force in the DRCm, SRC, and CBTC was also approximately equal, while the ligament force of the CBTC was found to be significantly greater than that of the DRCm and SRC at L1-L2. The results indicated that the stiffness associated with the CBTC might be lower than that associated with the DRCm and SRC in RS. The results of the present study indicated that the DRCm, SRC, and CBTC could provide sufficient stabilization in RS. The CBTC was a less rigid construct. Rather than the revision rod position, the method of constructing spinal instrumentation played a role in influencing the biomechanics of revision.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

The Influence of Loading Position in A Priori High Stress Detection using Mode Superposition

2020 ◽  
Vol 1 (1) ◽  
pp. 93-102
Author(s):  
Carsten Strzalka ◽  
◽  
Manfred Zehn ◽  
Keyword(s):  
Finite Element ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
A Priori ◽  
High Stress ◽  
Von Mises Stress ◽  
Detailed Knowledge ◽  
Variable Loading ◽  
Numerical Effort ◽  
Von Mises

For the analysis of structural components, the finite element method (FEM) has become the most widely applied tool for numerical stress- and subsequent durability analyses. In industrial application advanced FE-models result in high numbers of degrees of freedom, making dynamic analyses time-consuming and expensive. As detailed finite element models are necessary for accurate stress results, the resulting data and connected numerical effort from dynamic stress analysis can be high. For the reduction of that effort, sophisticated methods have been developed to limit numerical calculations and processing of data to only small fractions of the global model. Therefore, detailed knowledge of the position of a component’s highly stressed areas is of great advantage for any present or subsequent analysis steps. In this paper an efficient method for the a priori detection of highly stressed areas of force-excited components is presented, based on modal stress superposition. As the component’s dynamic response and corresponding stress is always a function of its excitation, special attention is paid to the influence of the loading position. Based on the frequency domain solution of the modally decoupled equations of motion, a coefficient for a priori weighted superposition of modal von Mises stress fields is developed and validated on a simply supported cantilever beam structure with variable loading positions. The proposed approach is then applied to a simplified industrial model of a twist beam rear axle.

scholarly journals Finite Element Analysis of Composite Repair for Damaged Steel Pipeline

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 301
Author(s):  
Jiaqi Chen ◽  
Hao Wang ◽  
Milad Salemi ◽  
Perumalsamy N. Balaguru
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Hoop Stress ◽  
Pipe Wall ◽  
Von Mises Stress ◽  
Repair System ◽  
Composite Repair ◽  
Steel Pipeline ◽  
Von Mises ◽  
Infill Material

Carbon fiber reinforced polymer (CFRP) matrix composite overwrap repair systems have been introduced and accepted as an alternative repair system for steel pipeline. This paper aimed to evaluate the mechanical behavior of damaged steel pipeline with CFRP repair using finite element (FE) analysis. Two different repair strategies, namely wrap repair and patch repair, were considered. The mechanical responses of pipeline with the composite repair system under the maximum allowable operating pressure (MAOP) was analyzed using the validated FE models. The design parameters of the CFRP repair system were analyzed, including patch/wrap size and thickness, defect size, interface bonding, and the material properties of the infill material. The results show that both the stress in the pipe wall and CFRP could be reduced by using a thicker CFRP. With the increase in patch size in the hoop direction, the maximum von Mises stress in the pipe wall generally decreased as the maximum hoop stress in the CFRP increased. The reinforcement of the CFRP repair system could be enhanced by using infill material with a higher elastic modulus. The CFRP patch tended to cause higher interface shear stress than CFRP wrap, but the shear stress could be reduced by using a thicker CFRP. Compared with the fully bonded condition, the frictional interface causes a decrease in hoop stress in the CFRP but an increase in von Mises stress in the steel. The study results indicate the feasibility of composite repair for damaged steel pipeline.

scholarly journals 3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

2021 ◽  
Vol 11 (6) ◽  
pp. 2547 ◽  
Author(s):  
Carlo Prati ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Alexandre Luiz Souto Borges ◽  
Maurizio Ventre ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Root Canal ◽  
Elastic Moduli ◽  
Reaction Force ◽  
Von Mises Stress ◽  
Elastic Behavior ◽  
Element Analysis ◽  
Heat Treated ◽  
Von Mises

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

scholarly journals Evaluation of Bone–Implant Interface Stress and Strain Using Heterogeneous Mandibular Bone Properties Based on Different Empirical Correlations

2021 ◽  
Author(s):  
Mostafa Omran Hussein ◽  
Mohammed Suliman Alruthea
Keyword(s):  
Finite Element ◽  
Group Iv ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Dental Arch ◽  
Stress And Strain ◽  
Bone Implant ◽  
Bone Properties ◽  
Group I ◽  
Von Mises

Abstract Objective The purpose of this study was to compare methods used for calculating heterogeneous patient-specific bone properties used in finite element analysis (FEA), in the field of implant dentistry, with the method based on homogenous bone properties. Materials and Methods In this study, three-dimensional (3D) computed tomography data of an edentulous patient were processed to create a finite element model, and five identical 3D implant models were created and distributed throughout the dental arch. Based on the calculation methods used for bone material assignment, four groups—groups I to IV—were defined. Groups I to III relied on heterogeneous bone property assignment based on different equations, whereas group IV relied on homogenous bone properties. Finally, 150 N vertical and 60-degree-inclined forces were applied at the top of the implant abutments to calculate the von Mises stress and strain. Results Groups I and II presented the highest stress and strain values, respectively. Based on the implant location, differences were observed between the stress values of group I, II, and III compared with group IV; however, no clear order was noted. Accordingly, variable von Mises stress and strain reactions at the bone–implant interface were observed among the heterogeneous bone property groups when compared with the homogenous property group results at the same implant positions. Conclusion Although the use of heterogeneous bone properties as material assignments in FEA studies seem promising for patient-specific analysis, the variations between their results raise doubts about their reliability. The results were influenced by implants’ locations leading to misleading clinical simulations.

Sign in / Sign up

Export Citation Format

Share Document