scholarly journals Adsorption Ability of Cephalexin onto the Straw-Based Activated Carbon: Performance and Mechanism

2020 ◽  
Vol 32 (8) ◽  
pp. 2084-2090
Author(s):  
Lam Van Tan ◽  
Hong-Tham Nguyen Thi ◽  
To-Uyen Dao Thi ◽  
Nguyen Thi Thuy Hong
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Bet Surface Area ◽  
Surface Material ◽  
Adsorption Ability ◽  
Initial Concentration ◽  
Carbon Performance ◽  
Adsorbent Materials ◽  
Performance And Mechanism

A straw-activated carbon has been successfully synthesized with the high BET surface area, at 494.9240 m2/g, which is perfectly suitable for the adsorption of cephalexin antibiotic from aqueous water. It is noted that the adsorption capacity of straw-activated carbon is demonstrated by the effect of initial concentration, contact time, pH solution and dosage. The straw-activated carbon exhibited improved decontaminant efficiency towards cephalexin antibiotics. Quick and improved sorption could be attributable to the distinctive structural and compositional merits as well as the synergetic contribution of functional groups to surface material. Most interestingly, the adsorption capacity achieved at pH 6 was ~98.52%. A mechanism adsorption has been proposed to demonstrate adsorption of the straw-activated carbon (AC-S). By comparison with other studies, it is confirmed that AC-S in this study obtained a higher removal efficiency than other adsorbent materials, suggesting that straw-activated carbon may be an appropriate candidate to treat cephalexin from wastewater media

scholarly journals Removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones

2019 ◽  
Vol 6 (2) ◽  
pp. 81-88 ◽  
Author(s):  
Dariush Naghipour ◽  
Abdoliman Amouei ◽  
Kamran Taher Ghasemi ◽  
Kamran Taghavi
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Contact Time ◽  
Wastewater Treatment Plants ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Pine Cones ◽  
Adsorbent Dose

Background: Metoprolol (MTP) with its low biodegradability is one of the most dominant micropollutant in the effluent of wastewater treatment plants. The aim of this study was to investigate the removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones. Methods: The pine cones were activated using thermal activation method. Characteristics of the adsorbent were determined using Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM). In this study, the influent of different parameters such as pH, contact time, initial concentrations of metoprolol, adsorbent dose, temperature, adsorption isotherms, and kinetics were investigated. Results: The maximum removal efficiency of MTP (89.2%) was obtained at pH=8.5, adsorbent dose=1.5 g, contact time=60 min, and initial concentration=50 mg/L. By increasing the adsorbent dose, the removal efficiency also increased, but the adsorption capacity decreased, however, by increasing the initial concentration, the removal efficiency decreased, but the adsorption capacity increased. The isotherm experimental data for metoprolol was best fitted using the Langmuir model, and kinetic data were better described by pseudo-second-order kinetic model. The thermodynamic study indicated that the adsorption of MTP by the adsorbent was feasible, spontaneous, and endothermic. Conclusion: MTP removal by the activated carbon prepared from pine cones showed that this natural adsorbent is appropriate for removal of metoprolol from aqueous solutions regarding cost, efficiency, and production method.

Nanoparticle Fe3O4 magnetized activated carbon from Armeniaca sibirica shell for the adsorption of Hg(II) ions

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 6100-6120
Author(s):  
Yinan Hao ◽  
Yanfei Pan ◽  
Qingwei Du ◽  
Xudong Li ◽  
Ximing Wang
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Entropy Change ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Initial Concentration

Armeniaca sibirica shell activated carbon (ASSAC) magnetized by nanoparticle Fe3O4 prepared from Armeniaca sibirica shell was investigated to determine its adsorption for Hg2+ from wastewater. Fe3O4/ASSAC was characterized using XRD (X-ray diffraction), FTIR (Fourier transform infrared spectroscopy), SEM (scanning electron microscopy), and BET (Brunauer–Emmett–Teller). Optimum adsorption parameters were determined based on the initial concentration of Hg2+, reaction time, reaction temperature, and pH value in adsorption studies. The experiment results demonstrated that the specific surface area of ASSAC decreased after magnetization; however the adsorption capacity and removal rate of Hg2+ increased 0.656 mg/g and 0.630%, respectively. When the initial concentration of Hg2+ solution was 250 mg/L and the pH value was 2, the adsorption time was 180 min and the temperature was 30 °C, and with the Fe3O4/ASSAC at 0.05 g, the adsorption reaching 97.1 mg/g, and the removal efficiency was 99.6%. The adsorption capacity of Fe3O4/ASSAC to Hg2+ was in accord with Freundlich isotherm models, and a pseudo-second-order kinetic equation was used to fit the adsorption best. The Gibbs free energy ΔGo < 0，enthalpy change ΔHo < 0, and entropy change ΔSo < 0 which manifested the adsorption was a spontaneous and exothermic process.

scholarly journals STUDI ADSORPSI ZAT WARNA NAPHTHOL YELLOW S PADA LIMBAH CAIR MENGGUNAKAN KARBON AKTIF DARI AMPAS TEBU

Jurnal Kimia ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 104
Author(s):  
W. P. Utoo1 ◽  
E. Santoso ◽  
G. Yuhaneka ◽  
A. I. Triantini ◽  
M. R. Fatqi ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Contact Time ◽  
Adsorption Process ◽  
Activation Process ◽  
Adsorption Model ◽  
High Adsorption ◽  
Prolonged Contact ◽  
Test Result

The aim of this research is to get activated carbon from sugarcane bagasse with high adsorption capacity to Naphthol Yellow S and to know factors influencing the adsorption capacity. Activated carbon is prepared by incomplete combustion of sugracane bagasse. The resulting carbon is activated with H2SO4 with concentration variation of 0.5; 1.0; 1.5 and 2.0 M and is continued by calcination at 400 °C. The measurement of the surface area of ??activated carbon by the methylene blue method indicates that the activation process successfully extends the surface area of carbon from 31.87 m2/g before activation to 66-72 m2/g after activation. Activated carbon with concentration of 2.0 M H2SO4 showed the highest surface area of ??71.85 m2/g, however, the best adsorption was shown by activated carbon with a concentration of 0.5 M H2SO4 with the adsorption capacity of 83.93%. The adsorption test showed that the best amount of adsorbent was 0.2 g with contact time for 30 minutes. Prolonged contact time can decrease the amount of Naphthol Yellow S adsorbed. The best adsorption test result was shown by sample with activator concentration of 0,5 M, mass of 0,2 g and contact time of 30 min with adsorption capacity 95,81% or amount of dye adsorbed equal to 143,72 mg/g. The adsorption study also showed that the entire Naphthol Yellow S adsorption process followed the Langmuir isothemal adsorption model. Qualitative testing of real batik waste indicates that activated carbon can reduce the dyes waste containing Naphthol Yellow Sexhibited by the color of batik waste which is more faded.  

Removal of Geosmin by Powered Activated Carbon as an Emergency Method

2014 ◽  
Vol 587-589 ◽  
pp. 616-619
Author(s):  
Zheng Wang ◽  
Dong Zhang ◽  
Ping Xia ◽  
Hui Ye ◽  
Wen Qi Zhou
Keyword(s):  
Activated Carbon ◽  
Contact Time ◽  
Adsorption Efficiency ◽  
Initial Concentration ◽  
Application Point ◽  
Removal Efficiencies

The removal of geosmin by powered activated carbon (PAC) was studied at laboratory to select suitable PAC type and the removal efficiencies of geosmin by PAC in different application point as an emergency method were evaluated. The adsorption efficiency of coal-based PAC on geosmin was superior to that of bamboo-based PAC. The contact time and PAC dose were two important factors that affect the removal effect of geosmin. Geosmin could be controled below 10ng/L at 200ng/L of initial concentration.

scholarly journals Phenol removal from aqueous solution using silica and activated carbon derived from rice husk

2019 ◽  
Vol 14 (4) ◽  
pp. 897-907 ◽  
Author(s):  
Hosseinali Asgharnia ◽  
Hamidreza Nasehinia ◽  
Roohollah Rostami ◽  
Marziah Rahmani ◽  
Seyed Mahmoud Mehdinia
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Water Treatment ◽  
Organic Pollutants ◽  
Rice Husk ◽  
Contact Time ◽  
Adsorption Process ◽  
Phenol Removal ◽  
Initial Concentration ◽  
Maximum Removal

Abstract Phenol and its derivatives are organic pollutants with dangerous effects, such as poisoning, carcinogenicity, mutagenicity, and teratogenicity in humans and other organisms. In this study, the removal of phenol from aqueous solution by adsorption on silica and activated carbon of rice husk was investigated. In this regard, the effects of initial concentration of phenol, pH, dosage of the adsorbents, and contact time on the adsorption of phenol were investigated. The results showed that the maximum removal of phenol by rice husk silica (RHS) and rice husk activated carbon (RHAC) in the initial concentration of 1 mgL−1 phenol, 2 gL−1 adsorbent mass, 120 min contact time, and pH 5 (RHS) or pH 6 (RHAC) were obtained up to 91% and 97.88%, respectively. A significant correlation was also detected between increasing contact times and phenol removal for both adsorbents (p &lt; 0.01). The adsorption process for both of the adsorbents was also more compatible with the Langmuir isotherm. The results of this study showed that RHS and RHAC can be considered as natural and inexpensive adsorbents for water treatment.

Physicochemical Properties of Carbons Prepared from Physic Nut Waste by Phosphoric Acid and Potassium Hydroxide Activations

2007 ◽  
Vol 561-565 ◽  
pp. 1719-1722 ◽  
Author(s):  
Chiravoot Pechyen ◽  
Duangdao Aht-Ong ◽  
Duangduen Atong ◽  
Viboon Sricharoenchaikul
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Physicochemical Properties ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Potassium Hydroxide ◽  
Bet Surface Area ◽  
Physic Nut ◽  
Monolayer Adsorption ◽  
Adsorption Data

Char derived from pyrolysis of physic nut waste at 400-800°C was used for the preparation of activated carbon by chemical impregnation of phosphoric acid and potassium hydroxide. The original char exhibited the BET surface area in the range of 120-250 m2·g-1. The surface area increased to 480 and 532 m2·g-1 when activated with H3PO4 and KOH, respectively. Equilibrium adsorption data was found to be best represented by the Langmuir isotherm with maximum monolayer adsorption capacity of 560.13 mg·g-1 at 30°C. The adsorption capacity of the physic nut residue activated carbon was comparable to commercial activated carbon.

Sorption of Methylene Blue and Acid Orange 7 onto Ananas comosus Peels and Leaves Based Activated Carbon

2013 ◽  
Vol 330 ◽  
pp. 112-116 ◽  
Author(s):  
Nabilah A. Lutpi ◽  
N. Najihah Jamil ◽  
C.K. Kairulazam C.K. Abdullah ◽  
Yee Shian Wong ◽  
Soon An Ong ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Contact Time ◽  
Time Effect ◽  
Ananas Comosus ◽  
Acid Orange 7 ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Acid Orange ◽  
Percentage Removal

The adsorption of Methylene Blue (MB) and Acid Orange 7 (AO7) dye onto Ananas Comosus Mixed Peels and Leaves (ACMPL) were carried out by conducting four different parameters such as initial concentration, pH, dosage of adsorbent, and contact time. Effect of initial concentration for both dyes showed that higher initial concentration would take longer contact time to attain equilibrium due to higher amount of adsorbate molecules. The effect of pH showed highest percentage removal for MB is at pH 9 which is 95.81%. Meanwhile for AO7 the highest percentage removal is 31.06% at pH 3. The percentage removal of MB had reached the equilibrium at dosage 0.5g while AO7 keep increasing with the increment of adsorbent dosage. The percentage removal of MB and AO7 had increased until hour 2.5 which was from 72.5% to 86.93% and 19.441% to 36.89% respectively and reached equilibrium at 3 hour contact time.

scholarly journals ADSORPSI ZAT WARNA METILEN BIRU DENGAN KARBON AKTIF DARI KULIT DURIAN MENGGUNAKAN KOH DAN NaOH SEBAGAI AKTIVATOR

2017 ◽  
Vol 6 (1) ◽  
pp. 49-55 ◽  
Author(s):  
Farida Hanum ◽  
Rikardo Jgst Gultom ◽  
Maradona Simanjuntak
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Contact Time ◽  
Wavelength Region ◽  
Second Order ◽  
Carbon Surface ◽  
Maximum Adsorption Capacity ◽  
Activation Process ◽  
Maximum Surface

Durian is a kind of tropical fruits which can grow well in Indonesia. Durian is containing 60-75% shell. Durian shell could be a potential alternative to activated carbon because it contains 57.42% carbon. The aim of this research is to know the effect of contact time and  stirring speed to activated carbon adsorption capacity from durian shell with KOH and NaOH as activators. FTIR (Fourier Transform Infra Red) analysis showed the activation process effects on  absorption intensity  wavelength region and resulted in formation of C = C aromatic tape, so that the nature of the charcoal becomes more polar compared with the initial condition. Analysis using spectrophotometer UV-Vis to determine  absorbance and  final concentration of each variation of contact time and stirring speed. The results showed that the maximum adsorption capacity obtained by activation of KOH and NaOH on stirring speed of 150 rpm and a contact time of 90 minutes is equal to 3.92 mg / g and 3.8 mg / g respectively. The maximum surface area obtained by activation of KOH and NaOH during the stirring speed 130 rpm and a contact time of 120 minutes is equal to 1785.263 m2 / g and 1730.332 m2 / g respectively. The maximum surface area obtained from this research has met the standards of commercial activated carbon surface area was between 800-1800 m2/ g. Modeling pseudo second order presents a more representative adsorption data, a second order equation is based on the assumption that adsorption step is chemosorption.

scholarly journals Single-Stage Microwave-Assisted Coconut-Shell-Based Activated Carbon for Removal of Dichlorodiphenyltrichloroethane (DDT) from Aqueous Solution: Optimization and Batch Studies

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Azrina Aziz ◽  
Mohamad Nasran Nasehir Khan ◽  
Mohamad Firdaus Mohamad Yusop ◽  
Erniza Mohd Johan Jaya ◽  
Muhammad Azan Tamar Jaya ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Radiation Power ◽  
Total Pore Volume ◽  
Single Stage ◽  
Coconut Shell ◽  
Bet Surface Area ◽  
Adsorption System ◽  
Average Pore ◽  
Preparation Conditions

This research aims to optimize preparation conditions of coconut-shell-based activated carbon (CSAC) and to evaluate its adsorption performance in removing POP of dichlorodiphenyltrichloroethane (DDT). The CSAC was prepared by activating the coconut shell via single-stage microwave heating under carbon dioxide, CO2 flow. The total pore volume, BET surface area, and average pore diameter of CSAC were 0.420 cm3/g, 625.61 m2/g, and 4.55 nm, respectively. The surface of CSAC was negatively charged shown by the zeta potential study. Response surface methodology (RSM) revealed that the optimum preparation conditions in preparing CSAC were 502 W and 6 min for radiation power and radiation time, respectively, which corresponded to 84.83% of DDT removal and 37.91% of CSAC’s yield. Adsorption uptakes of DDT were found to increase with an increase in their initial concentration. Isotherm study revealed that DDT-CSAC adsorption system was best described by the Langmuir model with monolayer adsorption capacity, Qm of 14.51 mg/g. The kinetic study confirmed that the pseudo-second-order model fitted well with this adsorption system. In regeneration studies, the adsorption efficiency had slightly dropped from 100% to 83% after 5 cycles. CSAC was found to be economically feasible for commercialization owing to its low production cost and high adsorption capacity.

scholarly journals PENGGUNAAN TANAH BENTONIT SEBAGAI ADSORBEN LOGAM Cu

2012 ◽  
Vol 1 (1) ◽  
pp. 1-4
Author(s):  
Daniel S Bath ◽  
Jenal M Siregar ◽  
M Turmuzi Lubis
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Strong Acid ◽  
Research Use ◽  
Activation Time ◽  
Adsorption Ability ◽  
Maximum Activation ◽  
Hcl Concentration

Bentonite serve the purpose of substance adsorpsi because swelling ability and cation for exchange. But adsorption ability is limited so that require to be activated by strong acid to higher level adsorption of bentonite. This research use Ca-Bentonit activated by strong acid HCl. Cation Cu analysed by using Spektofometri Serapan Atom (SSA).  Result of research  indicate that the increasing of HCl concentration and activation time can improve the adsorption capacity of bentonite. Maximum HCl concentration at 1,6 M and maximum activation time at 24 hour. Optimum heavy bentonite at 4 gr of 100 ppm Cu solution and optimum contact time at 2 hour. Result from Cu isoterm adsorption is weight of adsorption have same range with Cu concentration

Sign in / Sign up

Export Citation Format

Share Document