scholarly journals PENGGUNAAN TANAH BENTONIT SEBAGAI ADSORBEN LOGAM Cu

2012 ◽  
Vol 1 (1) ◽  
pp. 1-4
Author(s):  
Daniel S Bath ◽  
Jenal M Siregar ◽  
M Turmuzi Lubis
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Strong Acid ◽  
Research Use ◽  
Activation Time ◽  
Adsorption Ability ◽  
Maximum Activation ◽  
Hcl Concentration

Bentonite serve the purpose of substance adsorpsi because swelling ability and cation for exchange. But adsorption ability is limited so that require to be activated by strong acid to higher level adsorption of bentonite. This research use Ca-Bentonit activated by strong acid HCl. Cation Cu analysed by using Spektofometri Serapan Atom (SSA).  Result of research  indicate that the increasing of HCl concentration and activation time can improve the adsorption capacity of bentonite. Maximum HCl concentration at 1,6 M and maximum activation time at 24 hour. Optimum heavy bentonite at 4 gr of 100 ppm Cu solution and optimum contact time at 2 hour. Result from Cu isoterm adsorption is weight of adsorption have same range with Cu concentration

scholarly journals Adsorption Ability of Cephalexin onto the Straw-Based Activated Carbon: Performance and Mechanism

2020 ◽  
Vol 32 (8) ◽  
pp. 2084-2090
Author(s):  
Lam Van Tan ◽  
Hong-Tham Nguyen Thi ◽  
To-Uyen Dao Thi ◽  
Nguyen Thi Thuy Hong
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Bet Surface Area ◽  
Surface Material ◽  
Adsorption Ability ◽  
Initial Concentration ◽  
Carbon Performance ◽  
Adsorbent Materials ◽  
Performance And Mechanism

A straw-activated carbon has been successfully synthesized with the high BET surface area, at 494.9240 m2/g, which is perfectly suitable for the adsorption of cephalexin antibiotic from aqueous water. It is noted that the adsorption capacity of straw-activated carbon is demonstrated by the effect of initial concentration, contact time, pH solution and dosage. The straw-activated carbon exhibited improved decontaminant efficiency towards cephalexin antibiotics. Quick and improved sorption could be attributable to the distinctive structural and compositional merits as well as the synergetic contribution of functional groups to surface material. Most interestingly, the adsorption capacity achieved at pH 6 was ~98.52%. A mechanism adsorption has been proposed to demonstrate adsorption of the straw-activated carbon (AC-S). By comparison with other studies, it is confirmed that AC-S in this study obtained a higher removal efficiency than other adsorbent materials, suggesting that straw-activated carbon may be an appropriate candidate to treat cephalexin from wastewater media

scholarly journals Sintesis dan Karakterisasi Silika Abu Ampas Tebu Termodifikasi Arginin sebagai Adsorben Ion Logam Cu(II)

2018 ◽  
Vol 14 (2) ◽  
pp. 333
Author(s):  
Candra Purnawan ◽  
Tri Martini ◽  
Ima Puspita Rini
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Sol Gel ◽  
Ftir Analysis ◽  
Batch Method ◽  
Modified Silica ◽  
Adsorption Ability ◽  
Copper Adsorption ◽  
Ability Test

<p>Telah dilakukan penelitian tentang sintesis dan karakterisasi silika dari abu ampas tebu termodifikasi arginin dengan senyawa penggandeng glisidoksipropiltrimetoksisilan (GPTMS) sebagai adsorben ion logam Cu(II). Penelitian ini bertujuan untuk mengetahui karakterisasi silika abu ampas tebu termodifikasi arginin dengan senyawa penggandeng GPTMS sebagai adsorben ion logam Cu(II). Sintesis silika termodifikasi arginin dengan senyawa penggandeng GPTMS dilakukan dengan metode sol-gel. Adsorben tersebut dikarakterisasi dengan XRD, FTIR dan SAA. Uji kemampuan adsorpsi dilakukan menggunakan metode batch dengan larutan ion logam Cu(II), variasi pH, waktu kontak dan konsentrasi. Hasil penelitian menunjukkan perubahan difraktogram XRD pada silika termodifikasi dan silika abu ampas tebu (silika AAT). Difraktogram menunjukkan puncak melebar pada 2θ sebesar 10-15° dan 20-25°. Analisis FTIR menunjukkan Serapan baru –CH, ̶ NH tekuk, ̶ CN berturut-turut pada daerah 2947, 1570, dan 1356 cm<sup>-1</sup>. Analisis SAA menunjukkan peningkatan luas permukaan pada silika termodifikasi arginin daripada silika dari 64,31 m<sup>2</sup>/g menjadi 382,67 m<sup>2</sup>/g. Kondisi terbaik adsorpsi ion logam Cu(II) dengan adsorben silika termodifikasi arginin terjadi pada pH 6 dengan waktu kontak 45 menit. Silika termodifikasi arginin mengalami peningkatan kapasitas adsorpsi dibandingkan silika dengan kapasitas adsorpsi yaitu dari 0,12 mg/g menjadi 0,52 mg/g. Isoterm adsorpsi ion logam Cu(II) lebih dominan mengikuti isoterm Langmuir dengan r = 0,997.</p><p><strong>Synthesis </strong><strong>a</strong><strong>nd Characterization </strong><strong>o</strong><strong>f Arginine-Modified Silica </strong><strong>f</strong><strong>rom Baggase Ash </strong><strong>a</strong><strong>s C</strong><strong>u</strong><strong>(I</strong><strong>I</strong><strong>) Ions Adsorbent</strong><strong>.</strong> The synthesis and characterization of arginine modified silica from bagasse ash with crosslinker glycydoxypropyltrimethoxyxylane (GPTMS) as an adsorbent for Cu (II) ions has been studied. This research aimed to determine the characterization of arginine modified silica with crosslinker GPTMS as an adsorbent for Cu(II) ions. Synthesis arginine modified silica with crosslinker GPTMS was conducted using sol-gel method. The adsorbent was characterized by XRD, FTIR and SAA. Adsorption ability test conducted using the batch method with a solution of Cu(II) ions, variation of pH, contact time and concentration. The results showed the change in the XRD diffractogram of arginine modified silica from bagasse (silica ATT). XRD diffractogram releaved broad peaks at 2θ 10-15° and 20-25°. FTIR analysis showed a new absorption -CH, -NH bending, -C-N on area of 2947, 1570, and 1356 cm<sup>-1</sup>, respectively SAA analysis showed that the arginine-modified silica with crosslinker GPTMS has higher surface area than silica from 64.31 m<sup>2</sup>/g to 382.67 m<sup>2</sup>/g. The best conditions for copper adsorption with adsorbent arginine modified silica occured at pH 6 with a contact time of 45 minutes. Arginine modified silica has higher adsorption capacity than silica with a adsorption capacity from 0.12 mg/g to 0.52 mg/g. Adsorption of Cu (II) metal ions more dominantly follows Langmuir isotherms with r = 0.997.<strong></strong></p><p> </p>

scholarly journals Pengaruh HCl terhadap Aktifasi Zeolit Alam Clipnotilolit-Ca Pada Penyerapan Pb(II)

2020 ◽  
Vol 11 (2) ◽  
pp. 80-88
Author(s):  
Zilfa Zilfa ◽  
Upita Septiani ◽  
Mirawati Mirawati
Keyword(s):  
Particle Size ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Metal Ion ◽  
Activation Process ◽  
Acid Activation ◽  
Optimum Conditions ◽  
Hcl Concentration ◽  
Solution Volume

Research about the effect of HCl on the activation of clinoptilolite-Ca natural zeolite on Pb(II) absorption has been done. The purpose of this study is to determine the capacity of zeolite clinoptilolite-Ca activation by HCl can be used as an adsorbent. For analysis of the adsorption we used AAS whereas for zeolite characterization were used XRF and XRD. The analysis parameters are the effect of HCl concentration, particle size, adsorbent mass, contact time, total solution volume, concentration of Pb(II), and PH solution. These parameters were studied to determine the optimum conditions in the adsorption process. The optimum conditions absorption of Pb(II) for the acid activation process shows that the zeolite clinoptilolite-Ca can be used as an absorbent. The adsorption results show that the value of Pb(II) capacity in the activation process with HCl of 0.2 N produces adsorption capacity of 0.0821 mg/g, for particle size 125 µm produces and adsorption capacity 0.0821 mg/g, for an adsorbent mass of 0.1 g produces an adsorption capacity of 0.5110 mg/g, for contact time of 10 minutes is 0.5662 mg/g, for a metal solution volume of 12.5 mL is 0.5493 mg/g, for the concentration of metal ion solution 40 mg/L is 2.608 mg/g, and at pH = 7 is 4.923 mg/g. The output of several parameters can be concluded that the adsorption capacity of zeolite clinoptilolite-Ca to the absorption of Pb(II) is 4.923 mg/g. Characterization of zeolite adsorbents with XRF and XRD shows that the zeolite used is zeolite clinoptilolite-Ca.   

Development and Characterization of Amine-Clay Hybrid Adsorbents for CO2 Capture

2016 ◽  
Vol 1133 ◽  
pp. 547-551 ◽  
Author(s):  
Ali E.I. Elkhalifah ◽  
Mohammad Azmi Bustam ◽  
Azmi Mohd Shariff ◽  
Sami Ullah ◽  
Nadia Riaz ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
Surface Properties ◽  
Molar Mass ◽  
Adsorption Ability ◽  
Stepwise Increase ◽  
Inverse Effect ◽  
Bet Method ◽  
Sodium Form

The present work aims at a better understanding of the influences of the intercalated mono-, di- and triethanolamines on the characteristics and CO2 adsorption ability of sodium form of bentonite (Na-bentonite). The results revealed that the molar mass of intercalated amines significantly influenced the structural and surface properties as well as the CO2 adsorption capacity of Na-bentonite. In this respect, a stepwise increase in the d-spacing of Na-bentonite with the molar mass of amine was recorded by XRD technique. However, an inverse effect of the molar mass of amine on the surface area was confirmed by BET method. CO2 adsorption experiments on amine-bentonite hybrid adsorbents showed that the CO2 adsorption capacity inversly related to the molar mass of amine at 25 ͦC and 101 kPa. Accordingly, Na-bentonite modified by monoethanolammonium cations adsorbed as high as 0.475 mmol CO2/g compared to 0.148 and 0.087 mmol CO2/g for that one treated with di- and triethanolammonium cations, respectively.

scholarly journals Full Factorial Design for Gold Recovery from Industrial Solutions

Toxics ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 111
Author(s):  
Maria Mihăilescu ◽  
Adina Negrea ◽  
Mihaela Ciopec ◽  
Petru Negrea ◽  
Narcis Duțeanu ◽  
...  
Keyword(s):  
Factorial Design ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Design Method ◽  
Precious Metals ◽  
Gold Recovery ◽  
Maximum Adsorption Capacity ◽  
Gold Concentration ◽  
Commercial Resin

Gold is one of the precious metals with multiple uses, whose deposits are much smaller than the global production needs. Therefore, extracting maximum gold quantities from industrial diluted solutions is a must. Am-L-GA is a new material, obtained by an Amberlite XAD7-type commercial resin, functionalized through saturation with L-glutamic acid, whose adsorption capacity has been proved to be higher than those of other materials utilized for gold adsorption. In this context, this article presents the results of a factorial design experiment for optimizing the gold recovery from residual solutions resulting from the electronics industry using Am-L-GA. Firstly, the material was characterized using atomic force microscopy (AFM), to emphasize the material’s characteristics, essential for the adsorption quality. Then, the study showed that among the parameters taken into account in the analysis (pH, temperature, initial gold concentration, and contact time), the initial gold concentration in the solution plays a determinant role in the removal process and the contact time has a slightly positive effect, whereas the pH and temperature do not influence the adsorption capacity. The maximum adsorption capacity of 29.27 mg/L was obtained by optimizing the adsorption process, with the control factors having the following values: contact time ~106 min, initial Au(III) concentration of ~164 mg/L, pH = 4, and temperature of 25 °C. It is highlighted that the factorial design method is an excellent instrument to determine the effects of different factors influencing the adsorption process. The method can be applied for any adsorption process if it is necessary to reduce the number of experiments, to diminish the resources or time consumption, or for expanding the investigation domain above the experimental limits.

Chitosan-Bentonite Crosslinked Film As Indicator for Copper (II) Ions Adsorption

2021 ◽  
Author(s):  
Nurul Huda Osman ◽  
Nurul Najiha Mazu ◽  
Josephine Liew Ying Chyi ◽  
Muhammad Mahyiddin Ramli ◽  
Mohammad Abdull Halim Mohd Abdull Majid ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Impedance Spectroscopy ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Dc Conductivity ◽  
Dielectric Constants ◽  
Peak Amplitude ◽  
Electrical Parameters ◽  
Before And After

This paper reports on chitosan/bentonite crosslinked (ChB-ECH) film for removal of Cu (II). The effects of chitosan/bentonite ratio on the removal percentage were studied along with the effect of different Cu (II) concentration and the contact time on the film adsorption capacity, qt. The electrical properties of the film are studied, before and after the adsorption occurred, by using impedance spectroscopy for different parameters such as DC conductivity, the complex dielectric constants (ε’ and ε”) and complex electrical modulas (M’ and M’’). The results showed that the chitosan/bentonite ratio of 3:1 produces highest removal percentage at 29 %, while the contact time of 120 minutes was found to be optimum. An increment in the DC conductivity of the ChB-ECH film’s was observed up to 10-7 S/cm as the removal percentage of film increased. The film with the highest Cu (II) adsorb also showed the highest value for ε’ and ε” while exhibiting non-Derby behavior. Shifting of peak amplitude of the M” towards the higher frequency was also observed as the Cu (II) adsorption in the film increased. The results showed that all the electrical parameters can be utilized to determine the amount of adsorbed copper (II) in chitosan/bentonite film.

scholarly journals Adsorption Capacity of Ca2+ by Hydrochloric Acid Activated Kaolin

2021 ◽  
Vol 926 (1) ◽  
pp. 012082
Author(s):  
N Wahyuni
Keyword(s):  
Hydrochloric Acid ◽  
Adsorption Capacity ◽  
Calcium Ions ◽  
Contact Time ◽  
Maximum Adsorption Capacity ◽  
High Concentration ◽  
Straightforward Method ◽  
Diamine Tetraacetate ◽  
Ca Ions ◽  
Time Variations

Abstract A high concentration of calcium ions in water is a problem as it can cause blockages in engine pipes. Adsorption is a relatively cheap and straightforward method that can be used to reduce the calcium ion content in water. Kaolin is a mineral that has a potential as an adsorbent and whose adsorption capacity can be increased by activation. This research studied the adsorption capacity of activated kaolin by hydrochloric acid against Ca2+ ions. Kaolin was chemically activated using 6 M HCl solution for 24 hours. The adsorption contact time in batches was varied with time variations of 30, 90, 150, and 180 minutes. The maximum adsorption capacity of activated kaolin to the Ca2+ was determined by varying the initial concentrations of water samples, namely 4, 7, 10, and 13 mg/L. The concentration of Ca2+ was determined by a titration method using ethylene diamine tetraacetate (EDTA). The results showed that the activation of kaolin with 6 M HCl at the optimum contact time of adsorption, namely 150 minutes, increased the percentage of adsorbed Ca ions to 2 times of that of natural kaolin, from 33.3% to 68.3%. Based on the Langmuir equation, the maximum adsorption capacity of calcium ions by activated kaolin HCl 6 M increased 1.7 times from natural kaolin to 0.346 mg/g.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals PEMANFAATAN LIMBAH KULIT BUAH PISANG KEPOK (Musa paradisiaca) SEBAGAI BIOSORBEN ZAT WARNA RHODAMIN B

KOVALEN ◽  
2019 ◽  
Vol 5 (3) ◽  
pp. 308-314
Author(s):  
Musafira Musafira ◽  
Nurfitrah M Adam ◽  
Dwi Juli Puspitasari
Keyword(s):  
Adsorption Capacity ◽  
Rhodamine B ◽  
Contact Time ◽  
Banana Peel ◽  
Musa Paradisiaca ◽  
Randomized Design ◽  
Rhodamine B Dye ◽  
Completely Randomized Design ◽  
Maximum Contact ◽  
Rhodamin B

The investigation about the utilization of Banana peel (Musa paradisiaca) as biosorbent Rhodamine B dye has been done The purpose of this study was to determine the maximum contact time and to determine the adsorption capacity of kepok banana peel. Completely randomized design (CRD) was used in this research with two variables (the contact time and Rhodamine B concentration. Both variables were done in five levels i.e 10, 30, 60, 90, and 120 min and 2, 4, 6, 8 and 10 ppm respectively. The result showed that the maximum concentration of banana peel in adsorbing Rhodamine B was 6 ppm with 120 of contact time, and Rhodamine B adsorption capacity was  4.55mg/g. Keywords: Banana peel, Rhodamine B, biosorbent

scholarly journals ADSORPTION OF MALACHITE GREEN DYE USING SPENT COFFEE GROUND BIOCHAR: OPTIMISATION USING RESPONSE SURFACE METHODOLOGY

2020 ◽  
Vol 83 (1) ◽  
pp. 27-36
Author(s):  
Mardawani Mohamad ◽  
Rizki Wannahari ◽  
Rosmawani Mohammad ◽  
Noor Fazliani Shoparwe ◽  
Kwan Wei Lun ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Adsorption Capacity ◽  
Response Surface ◽  
Malachite Green ◽  
Contact Time ◽  
Quadratic Model ◽  
Adsorbent Dosage ◽  
Coffee Grounds ◽  
Spent Coffee Ground ◽  
Coffee Ground

Used coffee grounds usually end up as landfill. However, the unique structural properties of its porous surface make coffee grounds can be transformed into biochar and performed as an alternative low cost adsorbent. Malachite green (MG) is a readily water soluble dye which is used extensively in textile and aquaculture industries. The mordant complex structures of MG generate destructive effects to animals and environment. In this study, adsorption of malachite green using spent coffee ground biochar as adsorbent was investigated. The experiments were designed in two methods: classical and optimisation by response surface methodology. Three parameters were studied, which are adsorbent dosage, contact time and pH while the responses in this study are malachite green removal (%) and adsorption capacity (mg/g). Optimisation studies were performed using response surface methodology. Quadratic model was chosen for both response and studied using central composite design. The correlation coefficient, R2 for the quadratic model of malachite green removal (%) and adsorption capacity (mg/g) were 0.95 and 0.99, respectively. The optimum malachite green removal (%) predicted was found at 99.27%, by using 0.12 g of adsorbent dosage, 43.05 minutes of contact time and pH of 9.45 at desirability of 1.0. The optimum adsorption capacity (mg/g) predicted was found at 118.01 mg/g, by using 0.02 g of adsorbent dosage, 60 minutes of contact time and pH of 10.24 at desirability of 0.98. So, it was concluded that the spent coffee ground biochar can be used as an effective adsorbent for malachite green removal from aqueous solution.

Sign in / Sign up

Export Citation Format

Share Document