scholarly journals Fundamental Study of Electromagnetic Actuated Needle-Free Jet Injection

2018 ◽  
Vol 7 (3.7) ◽  
pp. 145
Author(s):  
Gittiphong Sripanagul ◽  
Anirut Matthujak
Keyword(s):  
High Speed ◽  
Video Camera ◽  
Polyacrylamide Gel ◽  
Orifice Diameter ◽  
Liquid Volume ◽  
Electromagnetic Actuator ◽  
Jet Injection ◽  
Fundamental Study ◽  
Free Jet ◽  
Jet Penetration

The objective of this paper is to preliminarily study the needle-free jet injection by electromagnetic actuator. The jets were generated by electromagnetic actuator, being designed and manufactured for this study. Effects of orifice diameter of the nozzle, travelling distance, voltage and liquid volume on jet velocity and impact pressure were investigated by laser beam interruption method and PVDF pressure sensor respectively. Moreover, the evolution of jet penetration during the injection into 20% Polyacrylamide gel was visualized by high-speed video camera. It was found that the electromagnetic actuator with the orifice diameter of 0.2 mm at travelling distance of 5 mm and voltage of 500 Volt at all liquid volumes can be applied for needle-free jet injection. The introductory channel as well as circular       dispersion was obviously observed seen from the evolution of jet penetration into 20% Polyacrylamide gel.  

A Model on Liquid Penetration Into Soft Material With Application to Needle-Free Jet Injection

2010 ◽  
Vol 132 (10) ◽  
Author(s):  
Kai Chen ◽  
Hua Zhou ◽  
Ji Li ◽  
Gary J. Cheng
Keyword(s):  
Mathematical Model ◽  
High Speed ◽  
Injection System ◽  
Liquid Jet ◽  
Liquid Penetration ◽  
Jet Injection ◽  
Free Jet ◽  
Calculation Results ◽  
Jet Penetration ◽  
Continuous Deposition

A mathematical model has been presented for a high speed liquid jet penetration into soft solid by a needle-free injection system. The model consists of a cylindrical column formed by the initial jet penetration and an expansion sphere due to continuous deposition of the liquid. By solving the equations of energy conservation and volume conservation, the penetration depth and the radius of the expansion sphere can be predicted. As an example, the calculation results were presented for a typical needle-free injection system into which a silicon rubber was injected into. The calculation results were compared with the experimental results.

EFFECT OF GEOMETRICAL PARAMETERS INTERACTION ON SWIRL EFFERVESCENT ATOMIZER SPRAY ANGLE

2015 ◽  
Vol 76 (9) ◽  
Author(s):  
Zulkifli Abdul Ghaffar ◽  
Salmiah Kasolang ◽  
Ahmad Hussein Abdul Hamid ◽  
Ow Chee Sheng ◽  
Mimi Azlina Abu Bakar
Keyword(s):  
High Speed ◽  
Video Camera ◽  
Spray Angle ◽  
Orifice Diameter ◽  
Working Fluid ◽  
Geometrical Parameters ◽  
High Speed Video Camera ◽  
Effervescent Atomizer ◽  
Vane Angle ◽  
Discharge Orifice

A wider spray angle produced by an atomizer is often required in providing a better spray dispersion. The formation and wideness of the spray angle were reported to be affected by the changes in geometrical parameters. In the present study, the effect of the interaction between two geometrical parameters (swirl-generating vane angle and discharge orifice diameter) on the swirl effervescent atomizer spray angle was studied. A newly-designed swirl effervescent atomizer was developed with 30°, 45° and 60° swirl-generating vane angle and 1.5, 2.0 and 2.5mm discharge orifice diameter. The atomizer performance tests were carried out using water as the working fluid and nitrogen gas as the atomizing agent. High-speed shadowgraph technique was deployed to record the resultant sprays produced. Video recordings, acquired using a high-speed video camera, were converted to a sequence of images for further analysis using image processing software. It was found that geometrical parameters of the newly designed atomizer have a great impact on the formation and characteristics of the spray angle. The combined effect of both swirl-generating vane angle and discharge orifice diameter has produced an increase in the spray angle. The largest spray angle was observed at the largest dimension of both geometries.

Visualization of Supersonic Non-Newtonian Liquid Jets

2012 ◽  
Vol 187 ◽  
pp. 63-67
Author(s):  
Anirut Matthujak ◽  
Chaidet Kasamnimitporn ◽  
Wuttichai Sittiwong ◽  
Kulachate Pianthong
Keyword(s):  
High Speed ◽  
Ambient Air ◽  
Video Camera ◽  
Newtonian Liquid ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Dynamic Behaviors ◽  
Penetration Distance ◽  
Jet Penetration ◽  
Jet Velocity

This paper describes the characteristics of supersonic non-Newtonian liquid jets injected in ambient air. The main focus is to visualize three types of time-independent non-Newtonian liquid jet and to describe their behaviors. Moreover, comparisons between their dynamic behaviors with Newtonian liquid jet are reported. The supersonic liquid jets are generated by impact driven method in a horizontal single-stage power gun. Jets have been visualized by the high speed digital video camera and shadowgraph method. Effects of different liquid types on the jet penetration distance, average jet velocity and other characteristics have been examined. From shadowgraph images, the unique dynamic behaviors of each non-Newtonian liquid jets are observed and found obviously different from that of the Newtonian liquid jet. The maximum average jet velocity of 1,802.18 m/s (Mach no. 5.30) has been obtained. The jet penetration distance and average velocity are significantly varied when the liquid types are different.

Effects of Different Liquid Properties on the Characteristics of Impact-Generated High-Speed Liquid Jets

2011 ◽  
Vol 110-116 ◽  
pp. 370-376 ◽  
Author(s):  
Anirut Matthujak ◽  
Chaidet Kasamnimitporn ◽  
Wuttichai Sittiwong ◽  
Kulachate Pianthong
Keyword(s):  
High Speed ◽  
Physical Property ◽  
Ambient Air ◽  
Video Camera ◽  
Orifice Diameter ◽  
Liquid Jets ◽  
Jet Formation ◽  
Digital Video Camera ◽  
Maximum Penetration ◽  
The Impact

This paper describes the study of high-speed liquid jets injected in air from an orifice. The main focus is to study the effect of different liquid properties on the characteristics of the high-speed liquid jets injected in ambient air. The high-speed liquid jets are generated by the impact of a projectile, which known as impact acceleration method, launched in a horizontal single-stage power gun (HSSPG). The conical nozzle of 30° angle with the orifice diameter of 0.7 mm was used to generate the jets. The characteristics of high-speed jets were visualized by the high-speed digital video camera with shadowgraph optical arrangement. From the shadowgraph images, the jet formation, atomization, vaporization and shock waves were obviously observed. The maximum averaged velocity of water, alcohol, n-hexane, chloroform and glycerin jets is estimated to be 1,669.03 m/s, 1,548.59 m/s, 1,420.44 m/s, 1,204.46 m/s and 1,496.97 m/s, respectively. That effect on the maximum penetration distance of the water jet is longer than that of all jets. Surface tension and latent heat are the significant physical property for jet formation, while density, kinematics viscosity and heat capacity are not.

Visualization of Pulsed Aerated Liquid Jet in Supersonic Cross Flow

2005 ◽  
Author(s):  
H. Sapmaz ◽  
B. Alkan ◽  
C. X. Lin ◽  
C. Ghenai
Keyword(s):  
Combustion Chamber ◽  
High Speed ◽  
Liquid Fuel ◽  
Cross Flow ◽  
Liquid Jet ◽  
Pure Liquid ◽  
Jet Injection ◽  
Fuel Jet ◽  
Air Mixing ◽  
Jet Penetration

The success of supersonic air-breathing propulsion systems will be largely dependent on efficient injection, mixing, and combustion inside the supersonic combustion chamber. Fuel/air mixing enhancement inside the combustion chamber will depend on the strategies used to control the fuel jet penetration and liquid fuel droplet size, trajectory, and dispersion. We present in these paper experimental results on the mixing of pure liquid jet, aerated liquid jet and pulsed aerated liquid jet in supersonic cross flow. Transverse aerated liquid jet injection will offer relatively rapid near-field mixing, good fuel penetration and better atomization of liquid fuel. Fully modulated or pulsed fuel jet injection will introduce additional supplementary turbulent mixing. High speed imaging system is used in this study for the visualization of the injection of liquid jet in high speed cross flow. The results presented in this paper show the effect of jet/cross flow momentum ratio, the gas/liquid mass ratio and pulsing frequency on the penetration of aerated liquid jet in supersonic cross-flow. The data generated in this study will be used for the development of active control strategies to optimize the liquid fuel jet penetration and supersonic fuel/air mixing.

scholarly journals Detonation effects of shallow buried explosive in sandy soil on target plate acceleration in a small-scale blast test

2018 ◽  
Vol 192 ◽  
pp. 02028
Author(s):  
Hassan Zulkifli Abu ◽  
Ibrahim Aniza ◽  
Mohamad Nor Norazman
Keyword(s):  
Sandy Soil ◽  
High Speed ◽  
Early Stage ◽  
Time History ◽  
Video Camera ◽  
Small Scale ◽  
Target Plate ◽  
Air Blast ◽  
High Speed Video Camera ◽  
The Impact

Small-scale blast tests were carried out to observe and measure the influence of sandy soil towards explosive blast intensity. The tests were to simulate blast impact imparted by anti-vehicular landmine to a lightweight armoured vehicle (LAV). Time of occurrence of the three phases of detonation phase in soil with respect to upward translation time of the test apparatus were recorded using high-speed video camera. At the same time the target plate acceleration was measured using shock accelerometer. It was observed that target plate deformation took place at early stage of the detonation phase before the apparatus moved vertically upwards. Previous data of acceleration-time history and velocity-time history from air blast detonation were compared. It was observed that effects of soil funnelling on blast wave together with the impact from soil ejecta may have contributed to higher blast intensity that characterized detonation in soil, where detonation in soil demonstrated higher plate velocity compared to what occurred in air blast detonation.

In Situ Observation Method for Quantitative Evaluation of Solidification Phenomena and Solidification Cracks during Welding

2014 ◽  
Vol 782 ◽  
pp. 3-7
Author(s):  
Kenji Shinozaki ◽  
Motomichi Yamamoto ◽  
Kohta Kadoi ◽  
Peng Wen
Keyword(s):  
High Speed ◽  
Video Camera ◽  
Solidification Cracking ◽  
In Situ Observation ◽  
High Speed Video Camera ◽  
Varestraint Test ◽  
Solidification Cracks ◽  
Observation Method ◽  
Solidification Crack

Solidification cracking during welding is very serious problem for practical use. Therefore, there are so many reports concerning solidification cracking. Normally, solidification cracking susceptibility of material is quantitatively evaluated using Trans-Varestraint test. On the other hand, local solidification cracking strain was tried to measure precisely using in-situ observation method, called MISO method about 30 years ago. Recently, digital high-speed video camera develops very fast and its image quality is very high. Therefore, we have started to observe solidification crack using in site observation method. In this paper, the local critical strain of a solidification crack was measured and the high temperature ductility curves of weld metals having different dilution ratios and different grain sizes to evaluate quantitatively the effects of dilution ratio and grain size on solidification cracking susceptibility by using an improved in situ observation method.

Study on Magnetic Barrel Machine Equipped with Three-Dimensional Arrangement of Magnets

2007 ◽  
Vol 329 ◽  
pp. 761-766 ◽  
Author(s):  
Y. Zhang ◽  
Masato Yoshioka ◽  
Shin-Ichiro Hira
Keyword(s):  
High Speed ◽  
Permanent Magnets ◽  
Three Dimensional ◽  
Video Camera ◽  
High Speed Video ◽  
High Speed Video Camera ◽  
The Media ◽  
Set Up

At present, a commercially available magnetic barrel machine equipped with permanent magnets has some faults arising from constructional reason. That is, grinding or finishing ability is different from place to place in the machining region, resulting in the limitation on the region we can use in the container of workpieces. Therefore, in this research, authors made the new magnetic barrel machine equipped with three dimensional (3D) magnet arrangement to overcome these faults. The grinding ability of the new 3D magnetic barrel machine converted was experimentally examined, and compared with that of the traditional magnetic barrel machine. As a result, it was shown that we can use much broader region in the new 3D machine. It was also shown that the grinding ability became higher. The distribution of barrel media in action was recorded by means of a high speed video camera. It was clarified that the media rose up higher and were distributed more uniformly in the container by the effect of the magnet block newly set up. It was supposed that this must be the reason for the above-mentioned improvement of grinding ability.

Sign in / Sign up

Export Citation Format

Share Document