Comparative Study of Two Types of Iron Doped Carbon Aerogels for Electrochemical Applications

2013 ◽  
Vol 16 (2) ◽  
pp. 097-101
Author(s):  
Delia Gligor ◽  
Liviu Cosmin Cotet ◽  
Virginia Danciu
Keyword(s):  
Exchange Process ◽  
Sol Gel ◽  
Carbon Aerogels ◽  
Carbon Paste ◽  
X Ray Diffraction ◽  
Ion Exchange Process ◽  
Transmission Electron ◽  
Good Electrocatalytic Activity ◽  
Bet Method ◽  
Iron Doped

Iron doped carbon aerogels have been prepared by sol-gel polymerization of potassium salt of 2,4-dihydroxybenzoic acid with formaldehyde followed by an ion-exchange process between K+ doped wet gel and Fe(II) or Fe(III) ion aqueous solutions. The resulted Fe(II) or Fe(III) doped gels have been dried in supercritical conditions with liquid CO2 and then pyrolyzed in high temperature resulting two types of iron doped carbon aerogels. These aerogels were morpho-structural investigated by using BET method, transmission electron microscopy, X-ray diffraction and elemental analysis. Also, these iron doped carbon aerogels (CAD-Fe(2+) and CAD-Fe(3+)) were tested for realization of modified carbon paste electrodes. CAD-Fe(2+) aerogel showed better electrochemical activity than CAD-Fe(3+) and also a good electrocatalytic activity towards H2O2 reduction (expressed by an electrocatalytic efficiency of 404% measured at – 500 mV vs. SCE).

scholarly journals Effect of RGO-Y2O3 and RGO-Y2O3:Cr3+ Nano Composite Sensor for Dopamine

2021 ◽  
Author(s):  
J Shashikumar ◽  
Bheenama Patil ◽  
B E KUMARA SWAMY ◽  
H Nagabhushana ◽  
S Sharma ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Emission Spectra ◽  
Modified Electrodes ◽  
Carbon Paste ◽  
X Ray Diffraction ◽  
Nano Composite ◽  
X Ray ◽  
Carbon Paste Electrodes ◽  
Transmission Electron ◽  
Good Electrocatalytic Activity

Abstract The RGO-Y2O3 and RGO-Y2O3: Cr3+ (5 mol %) nanocomposite (NC) synthesized a simple hydrothermal technique. The structure and morphology of the synthesized NCs were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Y2O3:Cr3+ display spherical shaped particles. Conversely, the surface of the RGO displays a wrinkly texture connecting with the existence of flexible and ultrathin graphene sheets. The photoluminescence (PL) emission spectra showed series of sharp peaks at 490, 591, and 687 nm which corresponding to 4F9/2→6H15/2, 4F9/2→6H13/2, and 4F9/2→6H11/2 transitions and lies in the blue, orange, and red region. The prepared NCs were used for the preparation of modified carbon paste electrodes (MCPE) in the electrochemical detection of dopamine (DA) at pH 7.4. Both modified electrodes provide a good electrocatalytic activity for the voltametric detection of DA. Doping is an effective method to improve the conductivity of Y2O3:Cr3+ and developed a method for the sensor used in analytical applications.

Study of the Synthesis and Photocatalytic Properties of Iron-Doped Titania Nanocrystallines at Room Temperature

2012 ◽  
Vol 562-564 ◽  
pp. 255-259
Author(s):  
Zhi Hao Wei ◽  
Min Zhong ◽  
Yin Deng
Keyword(s):  
Room Temperature ◽  
Sol Gel ◽  
Photocatalytic Properties ◽  
Iron Doping ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Iron Doped ◽  
Doped Titania ◽  
Average Size

Iron-doped titania (TiO2) nanocrystalline were prepared by sol-gel method at room temperature. The samples were characterized by using transmission electron microscope, X-ray diffractometer and ultaviolet-visible spectrophotometer. X-ray diffraction shows that iron-doped titania have the titania anatase and brookite structure, and the more iron doped in, the less titania brookite structure. When the doping content of 10at% iron, the titania brookite structure disappear absolutely. Transmission electron microscopy shows that with the increase of iron-doping from 0.00 to 0.25, the average size of the grains decrease from 5.7nm to 4.3nm. And samples have higher crystallinity. Using UV-visible spectrophotometer to measure its photocatalytic properties the results show that it has the highest rate of 60% photocatalytic degradation when it is absorbed in methylorange in two hours. With the increase of iron-doping from 0.00 to 0.25, the more iron doped in, the higher photocatalytic properties.

scholarly journals Influence of Nitrogen-Doped Carbon Dot and Silver Nanoparticle Modified Carbon Paste Electrodes on the Potentiometric Determination of Tobramycin Sulfate: A Comparative Study

Chemosensors ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 52
Author(s):  
Nermine V. Fares ◽  
Passant M. Medhat ◽  
Christine M. El Maraghy ◽  
Sherif Okeil ◽  
Miriam F. Ayad
Keyword(s):  
Silver Nanoparticle ◽  
Carbon Nanodots ◽  
Carbon Paste ◽  
X Ray Diffraction ◽  
Loteprednol Etabonate ◽  
Carbon Paste Electrodes ◽  
Transmission Electron ◽  
Nernstian Slope ◽  
Nitrogen Doped Carbon ◽  
Modified Carbon Paste Electrodes

Two inexpensive and simple methods for synthesis of carbon nanodots were applied and compared to each other, namely a hydrothermal and microwave-assisted method. The synthesized carbon nanodots were characterized using transmission electron microscopy (TEM), ultraviolet-visible (UV-Vis), photoluminescence (PL), Fourier transform-infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The synthesized microwave carbon nanodots had smaller particle size and were thus chosen for better electrochemical performance. Therefore, they were used for our modification process. The proposed electrodes performance characteristics were evaluated according to the IUPAC guidelines, showing linear response in the concentration range 10−6–10−2, 10−7–10−2, and 10−8–10−2 M of tobramycin with a Nernstian slope of 52.60, 58.34, and 57.32 mV/decade for the bare, silver nanoparticle and carbon nanodots modified carbon paste electrodes, respectively. This developed potentiometric method was used for quantification of tobramycin in its co-formulated dosage form and spiked human plasma with good recovery percentages and without interference of the co-formulated drug loteprednol etabonate and excipients.

scholarly journals The Influence Of NO/O2 On The NOx Storage Properties Over A Pt-Ba-Ce/γ-Al2O3 Catalyst

2019 ◽  
Vol 17 (1) ◽  
pp. 1459-1465
Author(s):  
Xuedong Feng ◽  
Jing Yi ◽  
Peng Luo
Keyword(s):  
Sol Gel ◽  
Chemical Properties ◽  
No Oxidation ◽  
Test Results ◽  
X Ray Diffraction ◽  
Storage Performance ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Physical And Chemical ◽  
Al2o3 Catalyst

AbstractWith the purpose of studying the influence of NO/O2 on the NOx storage activity, a Pt-Ba-Ce/γ-Al2O3 catalyst was synthesized by an acid-aided sol-gel method. The physical and chemical properties of the catalyst were characterized by X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) methods. The results showed that the composition of the catalyst was well-crystallized and the crystalline size of CeO2 (111) was about 5.7 nm. The mechanism of NO and NO2 storage and NOx temperature programmed desorption (NO-TPD) experiments were investigated to evaluate the NOx storage capacity of the catalyst. Pt-Ba-Ce/γ-Al2O3 catalyst presented the supreme NOx storage performance at 350℃, and the maximum value reached to 668.8 μmol / gcat. Compared with O2-free condition, NO oxidation to NO2 by O2 had a beneficial effect on the storage performance of NOx. NO-TPD test results showed that the NOx species stored on the catalyst surface still kept relatively stable even below 350℃.

scholarly journals V2O3/C composite fabricated by carboxylic acid-assisted sol–gel synthesis as anode material for lithium-ion batteries

2021 ◽  
Author(s):  
G. S. Zakharova ◽  
E. Thauer ◽  
A. N. Enyashin ◽  
L. F. Deeg ◽  
Q. Zhu ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Sol Gel ◽  
Carbon Sources ◽  
Lithium Ion ◽  
X Ray Diffraction ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Battery Electrode ◽  
Sol Gel Synthesis

AbstractThe potential battery electrode material V2O3/C has been prepared using a sol–gel thermolysis technique, employing vanadyl hydroxide as precursor and different organic acids as both chelating agents and carbon sources. Composition and morphology of resultant materials were characterized by X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopies, physical sorption, and elemental analysis. Stability and electronic properties of model composites with chemically and physically integrated carbon were studied by means of quantum-chemical calculations. All fabricated composites are hierarchically structured and consist of carbon-covered microparticles assembled of polyhedral V2O3 nanograins with intrusions of amorphous carbon at the grain boundaries. Such V2O3/C phase separation is thermodynamically favored while formation of vanadium (oxy)carbides or heavily doped V2O3 is highly unlikely. When used as anode for lithium-ion batteries, the nanocomposite V2O3/C fabricated with citric acid exhibits superior electrochemical performance with an excellent cycle stability and a specific charge capacity of 335 mAh g−1 in cycle 95 at 100 mA g−1. We also find that the used carbon source has only minor effects on the materials’ electrochemical performance.

Effect of Calcinations on Characterizations of Fabricated Nano Manganese Ferrite

2013 ◽  
Vol 634-638 ◽  
pp. 2150-2154 ◽  
Author(s):  
Rita Sundari ◽  
Tang Ing Hua ◽  
M. Rusli Yosfiah
Keyword(s):  
Sol Gel ◽  
Volatile Components ◽  
Manganese Ferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflectance Analysis ◽  
Transmission Electron Microscope Analysis ◽  
Electron Microscope Analysis ◽  
Nano Size

A citric acid anionic surfactant has been applied for nano manganese ferrite (MnFeO3) fabrication using sol gel method. The calcinations have been varied for 300, 600 and 800oC. The UVDR (UV-Vis Diffused Reflectance) analysis shows a high absorptive band gap after 400 nm for the 600oC calcinated MnFeO3. The DTA (Differential Thermal Analysis) profiles exhibit remarkably trapped volatile matters (H2O, CO2, and NO2) in the fabricated MnFeO3 under sol gel heat treatment at 100oC and the peaks disappeared as the calcination increased to 600oC. As the temperature elevated from 100 to 300oC, the absorption peaks of volatile components are disappeared as demonstrated clearly by the FTIR (Fourier Transform Infrared) spectra of the fabricated material, which 3393 cm-1 corresponded to OH group, 1624 cm-1 to CO group, and 1384 cm-1 to NO group. The XRD (X-Ray Diffraction) spectra show clearly the alteration process from amorphous to crystalline structure as the calcinations increased from 300 to 600oC. In addition, the TEM (Transmission Electron Microscope) analysis exhibits parts of the fabricated MnFeO3 found in cubic nano size of 15-40 nm under interested calcinations and the result is in agreement with that obtained by XRD investigation.

Researches on Preparation of Photosan Loaded Magnetic Silica Anoparticles and their Anti-Tumor Effects in Photodynamic Therapy

2012 ◽  
Vol 622-623 ◽  
pp. 821-826
Author(s):  
Yu Wen ◽  
Xiao Feng Deng ◽  
Liang Liang Liu ◽  
Shu Yun Shi ◽  
Li Xiong
Keyword(s):  
Drug Delivery ◽  
Photodynamic Therapy ◽  
Drug Delivery System ◽  
Delivery System ◽  
Sol Gel ◽  
Haematoporphyrin Derivative ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Good Biocompatibility ◽  
Low Solubility

Photodynamic therapy (PDT) is an effective, noninvasive and nontoxic therapeutics for cancer and some other diseases. It is becoming a alternative of traditional therapeutics for cancers. But the efficacy of PDT was restricted by insufficient selectivity and low solubility. In this study, novel multifunctional silica-based magnetic nanoparticles were prepared as targeting drug delivery system to achieve higher specificity and better solubility. Haematoporphyrin derivative (photosan) was used as photosensitizer. Magnetite nanoparticles (Fe3O4) and photosan were incorporated in silica nanoparticles by microemulsion and sol-gel methods. The prepared nanoparticles were characterized by X-ray diffraction, and transmission electron microscopy. The nanoparticles possessed good biocompatibility and could cause remarkable photodynamic anti-tumor effects. These suggested that photosan-Fe3O4 nanoparticles had great potential as effective drug delivery system in targeting photodynamic therapy.

Synthesis, Characterization, and Microwave Absorption Properties of SrFe12O19 Ferrites and FeNi3 Nanoplatelets Composites

2010 ◽  
Vol 148-149 ◽  
pp. 893-896 ◽  
Author(s):  
Ze Yang Zhang ◽  
Xiang Xuan Liu ◽  
You Peng Wu
Keyword(s):  
Electron Microscopy ◽  
Microwave Absorption ◽  
Composite Coatings ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Absorption Properties ◽  
Filling Fraction ◽  
Microwave Absorption Properties ◽  
Phase Reduction ◽  
Transmission Electron

M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were successfully prepared by the sol-gel method and solution phase reduction method, respectively. The crystalline and morphology of particles were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The composite coatings with SrFe12O19 ferrites and FeNi3 nanoplatelets in polyvinylchloride matrix were prepared. The microwave absorption properties of these coatings were investigated in 2-18GHz frequency range. The results showed that the M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were obtained and they presented irregular sheet shapes. With the increase of the coating thickness, the absorbing peak value moves to the lower frequency. The absorbing peak values of the wave increase along with the increasing of the content of FeNi3 nanoplatelets filling fraction. When 40% SrFe12O19 ferrites is doped with 20% mass fraction FeNi3 nanoplatelets to prepare composite with 1.5mm thickness, the maximum reflection loss is -24.8 dB at 7.9GHz and the -10 dB bandwidth reaches 3.2GHz.

The effect of silver concentration and calcination temperature on structural and optical properties of ZnO:Ag nanoparticles

2015 ◽  
Vol 29 (01) ◽  
pp. 1450254 ◽  
Author(s):  
M. Shayani Rad ◽  
A. Kompany ◽  
A. Khorsand Zak ◽  
M. E. Abrishami
Keyword(s):  
Calcination Temperature ◽  
Sol Gel ◽  
Visible Emission ◽  
X Ray Diffraction ◽  
Ag Nps ◽  
Zno Nps ◽  
Calcination Temperatures ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Average Size

Pure and silver added zinc oxide nanoparticles ( ZnO -NPs and ZnO : Ag -NPs) were synthesized through a modified sol–gel method. The prepared samples were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy. In the XRD patterns, silver diffracted peaks were also observed for the samples synthesized at different calcination temperatures of 500°C, 700°C, 900°C except 1100°C, in addition to ZnO . TEM images indicated that the average size of ZnO : Ag -NPs increases with the amount of Ag concentration. The PL spectra of the samples revealed that the increase of Ag concentration results in the increase of the visible emission intensity, whereas by increasing the calcination temperature the intensity of visible emission of the samples decreases.

A Novel Hydroxyapatite Carrier for Enrichment of Hydrocarbon Degradation Bacteria

2007 ◽  
Vol 336-338 ◽  
pp. 1914-1917
Author(s):  
Lei Yang ◽  
Zhen Yi Zhang ◽  
Xiao Shan Ning ◽  
Guang He Li
Keyword(s):  
Activated Carbon ◽  
Sol Gel ◽  
Hydrocarbon Degradation ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bacterial Enrichment ◽  
Bet Method ◽  
The One ◽  
Scanning Electron

In this paper, a novel and highly efficient hydroxyapatite (HA) carrier for cultivating hydrocarbon degradation bacteria (HDB) is introduced. The HA particles synthesized through a sol-gel method and different heat treatments were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and BET method. The microbial amount and activities of HDB cultivated on HA carriers were quantitatively investigated in order to assess their enriching capabilities. The results showed that HA synthesized at 550°C and the one without calcination could enrich HDB 3 and 2 magnitude orders more than the activated carbon, respectively. Mechanisms of bacterial enrichment on HA and activated carbon were also studied, and it is believed that the high bioactivity and the surface morphology of HA were responsible for the efficient reproduction of HDB. It is concluded that HA is a potential candidate to replace the conventionally used activated carbon as a novel carrier applied in the filed of bioremediation for oil contaminated soil.

Sign in / Sign up

Export Citation Format

Share Document