PROPERTIES OF CEMENT TREATED TIRE CRUMB AND OIL PALM FRUIT FIBER MORTAR

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
Farah Nora Aznieta Abdul Aziz ◽  
Sani Mohammed Bida ◽  
Noor Azline Mohd Nasir ◽  
Mohd Saleh Jaafar
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Oil Palm ◽  
Cement Content ◽  
Palm Fruit ◽  
Waste Tire ◽  
The Matrix ◽  
Absorption Measurements ◽  
Research Studies

Various research studies have been conducted in an effort to improve the mechanical properties of concretes and mortars containing waste tire particles using chemicals and additives which lead to increase cost. This approach presents an economical and sustainable method, through adding oil palm fruit fiber (OPFF) at 0.5%, 1%, and 1.5% by mass of cement content into the matrix and pre-treating the tire crumb aggregate (0-40%) by volume with cement, in order to improve the properties of the composite. Density, compressive strength and water absorption measurements were conducted on the mortar specimens. Results showed the addition of 0.5% OPFF in 10% treated tire crumb mortar was discovered to give the best improvement in the compressive strength of mortar modified with treated tire crumb.

Mechanical Properties of Mortar Modified with Cement Treated Tyre Crumb and Oil Palm Fruit Fibre

2015 ◽  
Vol 802 ◽  
pp. 225-230
Author(s):  
Farah Noor Abdul Aziz ◽  
Sani Mohammed Bida ◽  
Noor Azline Mohd Nasir ◽  
Nor Azizi Safiee ◽  
Mohd Saleh Jaafar
Keyword(s):  
Mechanical Properties ◽  
Oil Palm ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Material Research ◽  
Split Tensile Strength ◽  
Palm Fruit ◽  
The Matrix ◽  
Waste Tyre ◽  
Mechanical Strengths

Addition or replacement of waste tyre in mortars and concretes in lightweight aggregate concrete composites are popular in concrete material research although the mechanical properties of the composite are reduced. Various research studies have been conducted in an effort to improve the mechanical properties of concretes and mortars containing waste tyre particles using chemicals and additives which lead to increase cost. This approach presents an economical and sustainable method, through adding oil palm fruit fibre (OPFF) at 0.5, 1%, and 1.5% by mass of cement content into the matrix and pre-treating the tyre crumb aggregate (0-40%) by volume with cement, in order to improve the properties of the composite. Mechanical properties including compressive strength, split tensile strength and flexural strength were measured on the mortar specimens. Results showed the addition of 0.5% OPFF in 10% treated tyre crumb mortar gives the best improvement in the mechanical strengths of mortar modified with treated tyre crumb.

Characteristics and Properties of Reinforced Oil Palm Frond Fibers (OPFF) in Polyvinyl Alcohol (PVA) Composite for Tubular-Shaped Trays

2015 ◽  
Vol 751 ◽  
pp. 3-8
Author(s):  
Nawapon Sukudom ◽  
Lerpong Jarupan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Oil Palm ◽  
Morphological Properties ◽  
Degree Of Crystallinity ◽  
Poly Vinyl Alcohol ◽  
Oil Palm Frond ◽  
The Matrix ◽  
Twin Screw ◽  
Palm Frond

Effects on characteristics and mechanical properties of oil palm frond fiber (OPFF) as a reinforced element in poly vinyl alcohol (PVA) were investigated in this study. Series of different loading of OPFF were prepared by the following compositions: 5, 10, 15, 20 and 25 part per resin (phr). Glycerol at 35 phr was also compounded using twin-screw extruder to decrease degree of crystallinity and to reduce shear force of PVA to improve the processability. Injection molding was used to produce specimen for testing. The results indicated that the OPFF has an impact on mechanical properties of the composite material. Different scanning calorimeter (DSC) showed that the melting temperature (Tm) of OPFF reinforced PVA blended with glycerol was shifted to having decrease when compared to the pure PVA. Different loading contents of OPFF indicated that the compressive strength and morphological properties performed by a similar fashion. A highest compressive strength and the modulus of OPFF-reinforced PVA at 25 phr were achieved. Scanning electron microscope (SEM) indicated that OPFF-reinforced PVA at 25 phr yielded no accumulation of OPFF fibers but showed the dispersion in the matrix phase. In conclusion, the OPFF derived from oil palm industry can be used as reinforcement for manufacturing of plant pot in the future stage

Incorporation of Iraqi Rocks in the Production of Eco-Friendly Cement Mortar

2020 ◽  
Vol 38 (10A) ◽  
pp. 1522-1530
Author(s):  
Rawnaq S. Mahdi ◽  
Aseel B. AL-Zubidi ◽  
Hassan N. Hashim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Structural Properties ◽  
Mechanical Milling ◽  
Cement Mortar ◽  
Cement Mortars

This work reports on the incorporation of Flint and Kaolin rocks powders in the cement mortar in an attempt to improve its mechanical properties and produce an eco-friendly mortar. Flint and Kaolin powders are prepared by dry mechanical milling. The two powders are added separately to the mortars substituting cement partially. The two powders are found to improve the mechanical properties of the mortars. Hardness and compressive strength are found to increase with the increase of powders constituents in the cement mortars. In addition, the two powders affect water absorption and thermal conductivity of the mortar specimens which are desirable for construction applications. Kaolin is found to have a greater effect on the mechanical properties, water absorption, and thermal conductivity of the mortars than Flint. This behavior is discussed and analyzed based on the compositional and structural properties of the rocks powders.

Preparation of ZrO2 Composite Ceramics with High Thermal Shock Resistance

2012 ◽  
Vol 455-456 ◽  
pp. 650-654 ◽  
Author(s):  
He Yi Ge ◽  
Jian Ye Liu ◽  
Xian Qin Hou ◽  
Dong Zhi Wang
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Sintering Temperature ◽  
Fiber Composite ◽  
Physical And Mechanical Properties ◽  
Composite Ceramics ◽  
Shock Resistance ◽  
Absorption Measurements

The physical and mechanical properties of nanometer ZrO2-ZrO2fiber composite ceramics were studied by introduction of ZrO2fiber. ZrO2composite ceramics at different sintering temperature was investigated by porosity and water absorption measurements, flexual strength and thermal shock resistance analysis. Results showed that ZrO2composite ceramics containing 15 wt% ZrO2fiber with sintering temperature of 1650°C exhibited good mechanical properties and thermal shock resistance. The porosity and the water absorption were 8.84% and 1.62%, respectively. The flexual strength was 975 MPa and the thermal shock times reached 31 times. Scanning electron microscope (SEM) was used to analyze the microstructure of ZrO2composite ceramics.

Fabrication and Mechanical Properties of Dense/Porous β-Tricalcium Phosphate Bioceramics

2007 ◽  
Vol 330-332 ◽  
pp. 907-910
Author(s):  
Fa Ming Zhang ◽  
Jiang Chang ◽  
Jian Xi Lu ◽  
Kai Li Lin
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Exponential Growth ◽  
Weight Bearing ◽  
Area Ratio ◽  
Sectional Area ◽  
Cross Sectional ◽  
The Matrix ◽  
Porous Bioceramics

Attempt to increase the mechanical properties of porous bioceramics, a dense/porous structured β-TCP bioceramics that mimic the characteristics of nature bone were fabricated. Experimental results show that the dense/porous structured β-TCP bioceramics demonstrated excellent mechanical properties with compressive strength up to 74 MPa and elastic modulus up to 960 MPa, which could be tailored by the dense/porous cross-sectional area ratio obeying the rule of exponential growth. The interface between the dense and porous bioceramics is connected compactly and tightly with some micropores distributed in the matrix of both porous and dense counterparts. The dense/porous structure of β-TCP bioceramics may provide an effective way to increase the mechanical properties of porous bioceramics for bone regeneration at weight bearing sites.

scholarly journals Influence of the surface treatment of tire rubber residues added in mortars

2008 ◽  
Vol 1 (2) ◽  
pp. 113-120 ◽  
Author(s):  
A. C. Marques ◽  
J. L. Akasaki ◽  
A. P. M. Trigo ◽  
M. L. Marques
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Surface Treatment ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Tire Rubber ◽  
Flow Test ◽  
Made In

In this work it was evaluated the influence tire rubber addition in mortars in order to replace part of the sand (12% by volume). It was also intended to verify if the tire rubber treatment with NaOH saturated aqueous solution causes interference on the mechanical properties of the mixture. Compressive strength, splitting tensile strength, water absorption, modulus of elasticity, and flow test were made in specimens of 5cmx10cm and the tests were carried out to 7, 28, 56, 90, and 180 days. The results show reduction on mechanical properties values after addition of tire rubber and decrease of the workability. It was also observed that the tire rubber treatment does not cause any alteration on the results compared to the rubber without treatment.

The effect of ageing duration on the mechanical properties of Al alloy 6061-garnet composites

2001 ◽  
Vol 215 (2) ◽  
pp. 113-119
Author(s):  
S C Sharma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Al Alloy ◽  
Destructive Testing ◽  
Transmission Electron ◽  
Heat Treated ◽  
The Matrix ◽  
Reinforcing Particle ◽  
Alloy 6061

A well-consolidated composite of Al alloy 6061 reinforced with 4, 8 and 12 wt% garnet was prepared by a liquid metallurgy technique, the composite was heat treated for different ageing durations (T6 treatment), and its mechanical properties were determined by destructive testing. The results of the study indicated that, as the garnet particle content in the composites increased, there were marked increases in the ultimate tensile strength, compressive strength and hardness but there was a decrease in the ductility. There was an improvement in the tensile strength, compressive strength, and hardness with ageing due to precipitation. Precipitation in Al alloy 6061, with and without garnet particulate reinforcement, was studied using transmission electron microscopy. The fracture behaviour of the composites was altered significantly by the presence of garnet particles and the crack propagation through the matrix, and the reinforcing particle clusters resulted in final fracture.

Physical-Mechanical Properties of Paving Block from Plastic Shopping Bags Waste and Sand

2020 ◽  
Vol 849 ◽  
pp. 61-66
Author(s):  
Iswahyuni ◽  
Indri Hermiyati ◽  
Suharyanto ◽  
Uma Fadzilia Arifin ◽  
Dewi Nur Hidayati
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Economic Value ◽  
Plastic Waste ◽  
Alternative Solution ◽  
Friction Resistance ◽  
Plastic Bags ◽  
Fine Surface

Plastic shopping bags are easy to obtain for free or at low prices, hence contribute as the highest quantity among plastic waste. The plastic shopping bags waste has no economic value. Usually they are just thrown away. An alternative solution is by utilizing them to produce paving block by mixing with sands. The objective of this experiment is to evaluate the best ratio composition of plastic shopping bags waste and sand, followed by evaluation of the physical-mechanical properties of this particular paving block. Several different mixture ratios of weights of plastic shopping bag and sand were evaluated to obtain the best physical-mechanical properties of the paving block. The mixture ratios of weight of plastic shopping bags waste and sand were 1:1, 1:2, 1:3, 1:4 and 1:5, respectively. The shopping plastic bags waste was melted before mixed with sand. The different mixture ratios were mixed with same pressure. The paving block mixture with ratio of 1:4 exhibited the best physical-mechanical properties as revealed by no defect, no crack and fine surface. The compressive strength of 17.4 MPa, friction resistance of 0.138 mm/sec and water absorption of 2.518% can be achieved, which is suitable for parking area construction.

scholarly journals Investigation on cement-improved phyllite based on the vertical vibration compaction method

PLoS ONE ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. e0247599
Author(s):  
Yingjun Jiang ◽  
Jiangtao Fan ◽  
Yong Yi ◽  
Tian Tian ◽  
Kejia Yuan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Static Pressure ◽  
Cement Content ◽  
Vertical Vibration ◽  
Pressure Method ◽  
Vibration Compaction ◽  
Modulus Of Resilience ◽  
Compaction Method

The vertical vibration compaction method (VVCM), heavy compaction method and static pressure method were used to form phyllite specimens with different degrees of weathering. The influence of cement content, compactness, and compaction method on the mechanical properties of phyllite was studied. The mechanical properties of phyllite was evaluated in terms of unconfined compressive strength (Rc) and modulus of resilience (Ec). Further, test roads were paved along an expressway in China to demonstrate the feasibility of the highly weathered phyllite improvement technology. Results show that unweathered phyllite can be used as subgrade filler. In spite of increasing compactness, phyllite with a higher degree of weathering cannot meet the requirements for subgrade filler. With increasing cement content, Rc and Ec of the improved phyllite increases linearly. Rc and Ec increase by at least 15% and 17%, respectively, for every 1% increase in cement content and by at least 10% and 6%, respectively, for every 1% increase in compactness. The higher the degree of weathering of phyllite, the greater the degree of improvement of its mechanical properties.

Mechanical Properties and Thermal Conductivity of Lightweight Clay Bricks Fabricated with a Powdered Marble Dust Additive

2018 ◽  
Vol 777 ◽  
pp. 465-470
Author(s):  
Sutas Janbuala ◽  
Mana Eambua ◽  
Arpapan Satayavibul ◽  
Watcharakhon Nethan
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Apparent Porosity ◽  
Clay Brick ◽  
Clay Bricks ◽  
Marble Dust

The objective of this study was to recycle powdered marble dust to improve mechanical properties and thermal conductivity of lightweight clay bricks. Varying amounts of powdered marble dust (10, 20, 30, and 40 vol.%) were added to a lightweight clay brick at the firing temperatures of 900, 1000, and 1100 °C. When higher quantities of powdered marble dust were added, the values of porosity and water absorption increased while those of thermal conductivity and bulk density decreased. The decrease in apparent porosity and water absorption were also affected by the increase in firing temperature. The most desirable properties of the clay bricks were obtained for the powdered marble dust content of 40 vol.% and firing temperature 900 °C: bulk density of 1.20 g/cm3, compressive strength 9.2 MPa, thermal conductivity 0.32 W/m.K, and water absorption 22.5%.

Sign in / Sign up

Export Citation Format

Share Document