scholarly journals Study of Energy Consumption of Potato Slices During Drying Process

2015 ◽  
Vol 18 (2) ◽  
pp. 36-41
Author(s):  
Negar Hafezi ◽  
Mohammad Javad Sheikhdavoodi ◽  
Seyed Majid Sajadiye
Keyword(s):  
Radiation Power ◽  
Utilization Efficiency ◽  
Infrared Heating ◽  
Absolute Pressure ◽  
Slice Thickness ◽  
Drying Time ◽  
Infrared Lamp ◽  
The Absolute ◽  
Potato Slices

Abstract One of the new methods of food drying using infrared heating under vacuum is to increase the drying rate and maintain the quality of dried product. In this study, potato slices were dried using vacuum-infrared drying. Experiments were performed with the infrared lamp power levels 100, 150 and 200 W, absolute pressure levels 20, 80, 140 and 760 mmHg, and with three thicknesses of slices 1, 2 and 3 mm, in three repetitions. The results showed that the infrared lamp power, absolute pressure and slice thickness have important effects on the drying of potato. With increasing the radiation power, reducing the absolute pressure (acts of vacuum) in the dryer chamber and also reducing the thickness of potato slices, drying time and the amount of energy consumed is reduced. In relation to thermal utilization efficiency, results indicated that with increasing the infrared radiation power and decreasing the absolute pressure, thermal efficiency increased.

scholarly journals Optimization of the blanching of potato (Solanum tuberosum L) slices by response surface methodology: Effect on the vitamin C content and drying kinetics

2020 ◽  
pp. 17-32
Author(s):  
Ambe Desmond ◽  
Lobe Elias ◽  
Divine B. Nde
Keyword(s):  
Vitamin C ◽  
Solanum Tuberosum L ◽  
Negative Influence ◽  
Drying Kinetics ◽  
Slice Thickness ◽  
Drying Time ◽  
Quality Marker ◽  
Thin Layer Drying ◽  
Drying Behavior ◽  
Potato Slices

Potatoes (S. tuberosum L) is one of the most important tuber crops in the world. However, its high moisture content and inadequate storage and processing techniques have a negative influence on its quality and availability throughout the year. This work was carried out to optimize the blanching behavior and drying kinetics of potato slices. Fresh potato slices (5, 10 and 15 mm) were blanched at 70, 80 and 90°C for 1, 3 and 5 min following a 3k level full factorial design. The loss in Vitamin C was used as a quality marker for the optimization process. The influence of blanching on the drying behavior of potato slices was carried out at 50, 60 and 70°C. Results showed that blanching parameters had a significant (P < 0.05) effect on vitamin C loss. Optimum blanching conditions were blanching temperature of 80oC, blanching time of 3 min and a slice thickness of 10 mm which gave an average loss in Vitamin C of about 2.6%. Drying data were successfully fitted to three different thin layer drying models. The use of blanching as a pretreatment before the drying of potato is recommended because it reduces the drying time by 30%.

scholarly journals Drying Modelling, Moisture Diffusivity and Sensory quality of Thin Layer dried Beef

2018 ◽  
Vol 6 (2) ◽  
pp. 552-565 ◽  
Author(s):  
Eunice Akello Mewa ◽  
Michael Wandayi Okoth ◽  
Catherine Nkirote Kunyanga ◽  
Musa Njue Rugiri
Keyword(s):  
Thin Layer ◽  
Sensory Quality ◽  
Moisture Diffusivity ◽  
Drying Kinetics ◽  
Effect Of Temperature ◽  
Slice Thickness ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying

The objective of the present study was to determine the drying kinetics, moisture diffusivity and sensory quality of convective air dried beef. The effect of temperature of drying (30-60°C) and thickness of samples (2.5-10 mm) on the convective thin-layer drying kinetics of beefdried in a cabinet dryer was evaluated. Five semi-theoretical models were fit to the drying experimentaldata with the aim of predicting drying characteristics of beef and fitting quality of models determined using the standard error of estimate (SEE)and coefficient of determination (R2). Determination ofeffective moisture diffusivity (Deff) from the experimental drying datawas done and sensory quality of the optimized dried cooked and uncookedbeef samplesevaluated. Drying time and rate of drying increased with an increasing temperature but decreased with increased slice thickness. However, there was overlapping of drying curves at 40-50°C. Among the selected models, Page model gave the best prediction of beef drying characteristics. Effective moisture diffusivity (Deff) ranged between 4.2337 x 10-11 and 5.5899 x 10-10 m2/s, increasing with an increase in air temperature and beef slice thickness.Of all the sensory parameters evaluated, texture was the only attribute that gave significantly different (P > 0.05) scores between the cooked and uncooked dried beef samples.

Infrared Heating for Improved Drying Efficiency, Food Safety, and Quality of Rice

2019 ◽  
pp. 231-251 ◽  
Author(s):  
Ragab Khir ◽  
Chandrasekar Venkitasamy ◽  
Zhongli Pan
Keyword(s):  
Food Safety ◽  
Infrared Heating ◽  
Drying Efficiency ◽  
Food Safety And Quality

Study of color kinetics of banana (Musa cavendish) under microwave drying by application of image analysis

2020 ◽  
pp. 108201322098133
Author(s):  
Sagar Nagvanshi ◽  
Subbarao Kotra Venkata ◽  
TK Goswami
Keyword(s):  
Microwave Power ◽  
Vision System ◽  
Power Level ◽  
Microwave Drying ◽  
Slice Thickness ◽  
Order Kinetic ◽  
Drying Time ◽  
Volumetric Heating ◽  
Kinetics Of ◽  
Microwave Power Level

Microwave drying works on the volumetric heating concept promoted by electromagnetic radiation at 0.915 or 2.450 GHz. In this study, banana ( Musa Cavendish) was taken as the sample and treated under microwave drying. The effect of two process variables, namely slice thickness (2, 3.5, and 5 mm) and microwave power (180 W, 360 W, and 540 W), were studied on drying kinetics and color kinetics. It was observed that the inverse variation relationship exists between drying time and microwave power level while drying time and slice thickness exhibited a direct variation relationship. A Computer Vision System (CVS) was developed to measure the color values of banana in CIELab space using an algorithm written in MATLAB software. Once the color parameters were obtained, they were fitted in First and Zero-order kinetic models. Both models were found to describe the color values adequately. This study concludes that microwave drying is a promising dehydration technique for banana drying that reduces the significant time of drying. Application of CVS is an excellent approach to measure the surface color of banana.

scholarly journals The Quality of Red Bell Pepper Subjected to Freeze-Drying Preceded by Traditional and Novel Pretreatment

Foods ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 226
Author(s):  
Katarzyna Rybak ◽  
Artur Wiktor ◽  
Dorota Witrowa-Rajchert ◽  
Oleksii Parniakov ◽  
Małgorzata Nowacka
Keyword(s):  
Freeze Drying ◽  
Bell Pepper ◽  
Total Phenolic ◽  
Thermal Methods ◽  
Drying Time ◽  
Freeze Dried ◽  
Dehydration Processes ◽  
Vacuum Freezing ◽  
Better Than

It has been demonstrated previously in the literature that utilization of PEF or a combination of a pulsed electric field (PEF) and ultrasounds (US) can facilitate dehydration processes and improve the quality of dried products even better than the application of thermal methods such as blanching. The aim of the study was to evaluate the quality of red bell pepper subjected to freeze-drying preceded by blanching or PEF or US treatment applied in a single and combined mode. Furthermore, the freeze-drying was preceded by shock freezing or vacuum freezing performed inside the freeze-dryer as a result of pressure drop during the first stage of freeze-drying. All of the analyzed technological variants enhanced the drying kinetics when compared to the intact material. Freeze-dried bell pepper subjected to non-thermal pretreatment exhibited higher vitamin C, total phenolic and carotenoids content than blanched material despite the fact that blanching reduced drying time the most compared to all other analyzed methods.

scholarly journals Influence of Pear Variety and Drying Methods on the Quality of Dried Fruit

Molecules ◽  
2020 ◽  
Vol 25 (21) ◽  
pp. 5146
Author(s):  
Agata Marzec ◽  
Hanna Kowalska ◽  
Jolanta Kowalska ◽  
Ewa Domian ◽  
Andrzej Lenart
Keyword(s):  
Principal Component ◽  
Acoustic Method ◽  
Drying Methods ◽  
Drying Method ◽  
Drying Time ◽  
Good Taste ◽  
Dried Fruit ◽  
Breaking Work ◽  
Alexander Lucas

In this study, the impacts of two different pear cultivars, “Conference” and “Alexander Lucas”, on the kinetics and the final quality of samples dried by convection (CD) and microwave-convection (MCD) methods, were investigated. The quality of dried material was evaluated by the analysis of water activity, porosity, color, acoustic emission (AE) and mechanical and sensory properties. The required drying time to obtain 0.2 kg H2O/kg dry solid (d.s.) was longer for “Conference” than “Alexander Lucas” and was 20 min by CD and 5 min by MCD. The pear cultivar, in conjunction with the drying method (CD or MCD), affected the number of AE events and the work of breaking. The CD pear of the “Conference” cultivar was characterized by higher force, higher breaking work and stronger AE relative to the CD pear of the “Alexander Lucas” cultivar. There were no differences in taste or overall quality, but the hardness was higher for the CD “Conference” pear. A principal component analysis showed that panelists preferred dried fruit with good taste and overall quality but lower hardness. A positive correlation was found between the number of acoustic events and sensory hardness; thus, an acoustic method can be useful for effectively evaluating the texture of dried pears. These results show that the dried pear slices that generated fewer AE events upon breaking were perceived as better by the panelists.

CHANGES IN MOISTURE, TEMPERATURE, AND QUALITY OF CORN SEED DURING HIGH-TEMPERATURE DRYING

1989 ◽  
Vol 69 (3) ◽  
pp. 749-761 ◽  
Author(s):  
ULRICH HERTER ◽  
JOSEPH S. BURRIS
Keyword(s):  
Seed Quality ◽  
Inbred Lines ◽  
Drying Time ◽  
Temperature Changes ◽  
Corn Seed ◽  
Seed Corn ◽  
Seed Moisture ◽  
The Relationship ◽  
High Temperature Drying

Mechanical drying has frequently caused injury in corn seed. Changes in seed moisture, temperature, and quality were determined for inbred lines A632, B73 and Mo17 to define the relationship between these variables. Ears harvested at ca. 48 and 38% seed moisture could be dried at 50 °C for 4–15 h and 18–24 h, respectively, before germination started to decline linearly with prolonged 50 °C drying. Drying time at 50 °C, seed moisture, or embryo moisture after 50 °C drying could be used equally well for prediction of seed quality. Seedling dry weights often declined even when seed was dried for only a few hours at 50 °C. Temperature measurements within seeds indicated that evaporation cooled the seed no more than 5 °C. Drying susceptibility of seed parents varied greatly between years.Key words: Moisture, temperature changes, seed corn, drying

Effects of pre-drying on the quality of frying oil and potato slices

2017 ◽  
Vol 9 (3) ◽  
pp. 255-264 ◽  
Author(s):  
T.D. Capar ◽  
H. Yalcin
Keyword(s):  
Frying Oil ◽  
Potato Slices

scholarly journals KARAKTERISTIK FISIKOKIMIA PATI SAGU HASIL PENGERINGAN SECARA FLUIDISASI MENGGUNAKAN ALAT PENGERING CROSS FLOW FLUIDIZED BED BERTENAGA SURYA DAN BIOMASSA

REAKTOR ◽  
2011 ◽  
Vol 13 (3) ◽  
pp. 155 ◽  
Author(s):  
Abadi Jading ◽  
Eduard Tethool ◽  
Paulus Payung ◽  
Sarman Gultom
Keyword(s):  
Chemical Composition ◽  
Fluidized Bed ◽  
Cross Flow ◽  
Physicochemical Characteristics ◽  
Sago Starch ◽  
Drying Time ◽  
Fluidized Bed Dryer ◽  
Conventional Drying ◽  
Fluidized Bed Drying

PHYSICOCHEMICAL CHARACTERISTICS OF SAGO STARCH OBTAINED FROM FLUIDIZED BED DRYING USING SOLAR AND BIOMASS POWERED CROSS FLOW FLUIDIZED BED DRYER. The research aim is to study the comparative quality of sago starch drying results using cross flow fluidized bed dryer powered by solar and biomass in conventional drying, particularly the chemical composition and physicochemical characteristics. This research was conducted through a drying phase of wet sago starch using a cross flow fluidized bed dryer, and drying in conventional as well as dried sago starch quality testing results are drying. The results of this study indicate that dry sago starch which has been drained by means of cross flow fluidized bed dryer has a chemical composition that does not vary much with starch which is dried by conventional drying, so that the dried sago starch produced by the dryer is very good. On the other hand the use of dryers is the more correct because the physicochemical properties of sago starch using a low drying temperature and drying time is short. Tujuan penelitian ini adalah mempelajari perbandingan kualitas pati sagu hasil pengeringan menggunakan alat pengering cross flow fluidized bed bertenaga surya dan biomassa dengan pengeringan secara konvensional, khususnya komposisi kimia dan karakteristik fisikokimia. Penelitian ini dilakukan melalui beberapa tahapan yaitu pengeringan pati sagu basah menggunakan alat pengering cross flow fluidized bed, pengeringan secara konvensional serta pengujian kualitas pati sagu kering hasil pengeringan. Hasil dari penelitian ini menunjukkan bahwa pati sagu kering yang telah dikeringkan dengan alat pengering cross flow fluidized bed memiliki komposisi kimia yang tidak berbeda jauh dengan pati yang dikeringkan dengan cara pengeringan secara konvensional, sehingga pati sagu kering yang dihasilkan oleh alat pengering tersebut sangat baik. Di sisi lain penggunaan alat pengering ini semakin memperbaiki sifat fisikokimia pati sagu sebab menggunakan suhu pengeringan yang rendah dan waktu pengeringan yang singkat.   Kata Kunci: pengering unggun terfluidakan; fisikokimia; pati sagu

Sign in / Sign up

Export Citation Format

Share Document