Enhancement of Catalytic Performance of H-Clinoptilolite in Toluene Abatement from Polluted Air via Controlled Dealumination Method

2018 ◽  
Vol 16 (5) ◽  
Author(s):  
Naser Ghasemian ◽  
Ali Reza Yousefi
Keyword(s):  
Oxalic Acid ◽  
Chemical Modification ◽  
Treatment Period ◽  
Acid Site ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Total Oxidation ◽  
Maximum Conversion ◽  
First Time ◽  
Mild Acid

AbstractIn this study, the effect of clinoptilolite dealumination on the total oxidation of toluene was reported for the first time. To avoid excess decrease of catalyst crystallinity, chemical modification of zeolite was carried out using a mild acid like oxalic acid. The catalysts were characterized by XRD, XRF, SEM, BET and TPD analyses. It was found that dealumination resulted in a significant enhancement of toluene conversion when 0.050 M acid oxalic was used for a treatment period of 2 h. Dealumination substantially changed the distribution of the concentration of acid sites of different strength and increased the surface area and porosity, so that the temperature corresponding to the maximum conversion shifts around 50 °C towards lower temperatures (in case of CLP 050). The effect of dealumination on the activity of the zeolite samples and the total oxidation of toluene was discussed in terms of Si/Al ratio, crystallinity, distribution of acid site strength and textural characteristics of the samples.

scholarly journals Insight into Active Centers and Anti-Coke Behavior of Niobium-Containing SBA-15 for Glycerol Dehydration

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 488
Author(s):  
Katarzyna Stawicka ◽  
Maciej Trejda ◽  
Maria Ziolek
Keyword(s):  
Coke Formation ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Silica Matrix ◽  
High Concentration ◽  
Active Centers ◽  
Acidic Sites ◽  
Glycerol Dehydration ◽  
Adsorption Desorption ◽  
Insight Into

Niobium containing SBA-15 was prepared by two methods: impregnation with different amounts of ammonium niobate(V) oxalate (Nb-15/SBA-15 and Nb-25/SBA-15 containing 15 wt.% and 25 wt.% of Nb, respectively) and mixing of mesoporous silica with Nb2O5 followed by heating at 500 °C (Nb2O5/SBA-15). The use of these two procedures allowed obtaining materials with different textural/surface properties determined by N2 adsorption/desorption isotherms, XRD, UV-Vis, pyridine, and NO adsorption combined with FTIR spectroscopy. Nb2O5/SBA-15 contained exclusively crystalline Nb2O5 on the SBA-15 surface, whereas the materials prepared by impregnation had both metal oxide and niobium incorporated into the silica matrix. The niobium species localized in silica framework generated Brønsted (BAS) and Lewis (LAS) acid sites. The inclusion of niobium into SBA-15 skeleton was crucial for the achievement of high catalytic performance. The strongest BAS were on Nb-25/SBA-15, whereas the highest concentration of BAS and LAS was on Nb-15/SBA-15 surface. Nb2O5/SBA-15 material possessed only weak LAS and BAS. The presence of the strongest BAS (Nb-25/SBA-15) resulted in the highest dehydration activity, whereas a high concentration of BAS was unfavorable. Silylation of niobium catalysts prepared by impregnation reduced the number of acidic sites and significantly increased acrolein yield and selectivity (from ca. 43% selectivity for Nb-25/SBA-15 to ca. 61% for silylated sample). This was accompanied by a considerable decrease in coke formation (from 47% selectivity for Nb-25/SBA-15 to 27% for silylated material).

scholarly journals Influence of Alumina Precursor Properties on Cu-Fe Alumina Supported Catalysts for Total Toluene Oxidation as a Model Volatile Organic Air Pollutant

Catalysts ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 252
Author(s):  
Tadej Žumbar ◽  
Alenka Ristić ◽  
Goran Dražić ◽  
Hristina Lazarova ◽  
Janez Volavšek ◽  
...  
Keyword(s):  
Surface Characterization ◽  
Iron Concentration ◽  
Catalytic Performance ◽  
Air Pollutant ◽  
Molar Ratio ◽  
Homogeneous Distribution ◽  
Total Oxidation ◽  
Alumina Support ◽  
Determining Factors ◽  
Volatile Organic

The structure–property relationship of catalytic supports for the deposition of redox-active transition metals is of great importance for improving the catalytic efficiency and reusability of the catalysts. In this work, the role of alumina support precursors of Cu-Fe/Al2O3 catalysts used for the total oxidation of toluene as a model volatile organic air pollutant is elucidated. Surface characterization of the catalysts revealed that the surface area, pore volume and acid site concentration of the alumina supports are important but not the determining factors for the catalytic activity of the studied catalysts for this type of reaction. The determining factors are the structural order of the support precursor, the homogeneous distribution of the catalytic sites and reducibility, which were elucidated by XRD, NMR, TEM and temperature programed reduction (TPR). Cu–Fe/Al2O3 prepared from bayerite and pseudoboehmite as highly ordered precursors showed better catalytic performance compared to Cu-Fe/Al2O3 derived from the amorphous alumina precursor and dawsonite. Homogeneous distribution of FexOy and CuOx with defined Cu/Fe molar ratio on the Al2O3 support is required for the efficient catalytic performance of the material. The study showed a beneficial effect of low iron concentration introduced into the alumina precursor during the alumina support synthesis procedure, which resulted in a homogeneous metal oxide distribution on the support.

Growth kinetic control over MgFe2O4 to tune Fe occupancy and metal–support interactions for optimum catalytic performance

CrystEngComm ◽  
2021 ◽  
Vol 23 (13) ◽  
pp. 2538-2546
Author(s):  
Min Yang ◽  
Guangshe Li ◽  
Huixia Li ◽  
Junfang Ding ◽  
Yan Wang ◽  
...  
Keyword(s):  
Co Oxidation ◽  
Growth Kinetic ◽  
Catalytic Performance ◽  
Growth Behavior ◽  
Kinetic Control ◽  
Size Dependent ◽  
Metal Support ◽  
Support Size ◽  
Metal Support Interactions ◽  
First Time

For the first time, the growth behavior with size-dependent Fe occupancies at different sites of MgFe2O4 was examined. Hybrid catalysts of Pt/MgFe2O4 with a support size of 20.6 nm exhibited an optimal performance of CO oxidation.

scholarly journals Theoretical Study of Zirconium Isomorphous Substitution into Zeolite Frameworks

Molecules ◽  
2019 ◽  
Vol 24 (24) ◽  
pp. 4466
Author(s):  
Duichun Li ◽  
Bin Xing ◽  
Baojun Wang ◽  
Ruifeng Li
Keyword(s):  
Acid Site ◽  
Density Functional ◽  
Theoretical Study ◽  
Atomic Radius ◽  
Acid Sites ◽  
Isomorphous Substitution ◽  
Dispersion Correction ◽  
Brønsted Acidity ◽  
Functional Theory ◽  
Brönsted Acidity

Systematic periodic density functional theory computations including dispersion correction (DFT-D) were carried out to determine the preferred location site of Zr atoms in sodalite (SOD) and CHA-type topology frameworks, including alumino-phosphate-34 (AlPO-34) and silico-alumino-phosphate-34 (SAPO-34), and to determine the relative stability and Brönsted acidity of Zr-substituted forms of SOD, AlPO-34, and SAPO-34. Mono and multiple Zr atom substitutions were considered. The Zr substitution causes obvious structural distortion because of the larger atomic radius of Zr than that of Si, however, Zr-substituted forms of zeolites are found to be more stable than pristine zeolites. Our results demonstrate that in the most stable configurations, the preferred favorable substitutions of Zr in substituted SOD have Zr located at the neighboring sites of the Al-substituted site. However, in the AlPO-34 and SAPO-34 frameworks, the Zr atoms are more easily distributed in a dispersed form, rather than being centralized. Brönsted acidity of substituted zeolites strongly depends on Zr content. For SOD, substitution of Zr atoms reduces Brönsted acidity. However, for Zr-substituted forms of AlPO-34 and SAPO-34, Brönsted acidity of the Zr-O(H)-Al acid sites are, at first, reduced and, then, the presence of Zr atoms substantially increased Brönsted acidity of the Zr-O(H)-Al acid site. The results in the SAPO-34-Zr indicate that more Zr atoms substantially increase Brönsted acidity of the Si-O(H)-Al acid site. It is suggested that substituted heteroatoms play an important role in regulating and controlling structural stability and Brönsted acidity of zeolites.

scholarly journals Ruling Factors in Cinnamaldehyde Hydrogenation: Activity and Selectivity of Pt-Mo Catalysts

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 362
Author(s):  
Marta Stucchi ◽  
Maela Manzoli ◽  
Filippo Bossola ◽  
Alberto Villa ◽  
Laura Prati
Keyword(s):  
Photoelectron Spectroscopy ◽  
Pt Nanoparticles ◽  
Carbon Support ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Hydrogenation Catalysts ◽  
Cinnamaldehyde Hydrogenation ◽  
Transmission Electron ◽  
Heat Treated ◽  
Heating Treatment

To obtain selective hydrogenation catalysts with low noble metal content, two carbon-supported Mo-Pt bimetallic catalysts have been synthesized from two different molybdenum precursors, i.e., Na2MoO4 and (NH4)6Mo7O24. The results obtained by X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) combined with the presence and strength of acid sites clarified the different catalytic behavior toward cinnamaldehyde hydrogenation. After impregnating the carbon support with Mo precursors, each sample was used either as is or treated at 400 °C in N2 flow, as support for Pt nanoparticles (NPs). The heating treatment before Pt deposition had a positive effect on the catalytic performance. Indeed, TEM analyses showed very homogeneously dispersed Pt NPs only when they were deposited on the heat-treated Mo/C supports, and XPS analyses revealed an increase in both the exposure and reduction of Pt, which was probably tuned by different MoO3/MoO2 ratios. Moreover, the different acid properties of the catalysts resulted in different selectivity.

Efficient Modulation of Catalytic Performance of Electrocatalytic Nitrogen Reduction with Transition Metal Anchored N/O-codoped Graphene by Coordination Engineering

2021 ◽  
Author(s):  
Xiaolin Wang ◽  
Li-Ming Yang
Keyword(s):  
Nitrogen Fixation ◽  
Transition Metal ◽  
High Throughput ◽  
First Principles ◽  
High Throughput Screening ◽  
Catalytic Performance ◽  
Nitrogen Reduction ◽  
Highly Efficient ◽  
First Time

We for the first time report the discovery of a series of highly efficient electrocatalysts, i.e., transition metal anchored N/O-codoped graphene, for nitrogen fixation via high-throughput screening combined with first-principles...

scholarly journals Influence of Sulfur-Containing Sodium Salt Poisoned V2O5–WO3/TiO2 Catalysts on SO2–SO3 Conversion and NO Removal

Catalysts ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 541 ◽  
Author(s):  
Haiping Xiao ◽  
Chaozong Dou ◽  
Hao Shi ◽  
Jinlin Ge ◽  
Li Cai
Keyword(s):  
Photoelectron Spectroscopy ◽  
No Reduction ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Impregnation Method ◽  
So2 Oxidation ◽  
Sodium Salts ◽  
X Ray ◽  
Temperature Programmed ◽  
Physical Features

A series of poisoned catalysts with various forms and contents of sodium salts (Na2SO4 and Na2S2O7) were prepared using the wet impregnation method. The influence of sodium salts poisoned catalysts on SO2 oxidation and NO reduction was investigated. The chemical and physical features of the catalysts were characterized via NH3-temperature programmed desorption (NH3-TPD), H2-temperature programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FT-IR). The results showed that sodium salts poisoned catalysts led to a decrease in the denitration efficiency. The 3.6% Na2SO4 poisoned catalyst was the most severely deactivated with denitration efficiency of only 50.97% at 350 °C. The introduction of SO42− and S2O72− created new Brønsted acid sites, which facilitated the adsorption of NH3 and NO reduction. The sodium salts poisoned catalysts significantly increased the conversion of SO2–SO3. 3.6%Na2S2O7 poisoned catalyst had the strongest effect on SO2 oxidation and the catalyst achieved a maximum SO2–SO3-conversion of 1.44% at 410 °C. Characterization results showed sodium salts poisoned catalysts consumed the active ingredient and lowered the V4+/V5+ ratio, which suppressed catalytic performance. However, they increased the content of chemically adsorbed oxygen and the strength of V5+=O bonds, which promoted SO2 oxidation.

scholarly journals Simultaneous Catalytic Oxidation of a Lean Mixture of CO-CH4 over Spinel Type Cobalt Based Oxides

2020 ◽  
Vol 15 (2) ◽  
pp. 490-500
Author(s):  
Neha Neha ◽  
Ram Prasad ◽  
Satya Vir Singh
Keyword(s):  
Mixed Oxides ◽  
Structural Disorder ◽  
Catalytic Performance ◽  
Molar Ratio ◽  
Total Oxidation ◽  
Spinel Type ◽  
Molar Ratios ◽  
Long Term Stability ◽  
Nickel Cobalt ◽  
Temperature Programmed

A series of nickel-cobalt bimetal oxides in varying molar ratios and its single metal oxides were synthesized by reactive calcination of coprecipitated basic-carbonates. Several characterization techniques, such as: Bruneuer Emmett Teller (BET), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier Transform Infra Red (FTIR), and Hydrogen Temperature Programmed Reduction (H2-TPR), were performed over the oxides. Activities of oxides were evaluated in methane total oxidation in the presence or the absence of CO. The best catalytic performance was observed over NiCo catalyst with a Ni/Co molar ratio of 1:1, and the complete conversion of CO-CH4 mixture was achieved at 390 °C. Moreover, the presence of carbon monoxide improves CH4 total oxidation over nickel-cobalt mixed oxides. Structural analysis reveals that the insertion of nickel into the spinel lattice of cobalt oxide causes the structural disorder, which probably caused the increase of the amount of octahedrally coordinated divalent nickel cations that are responsible for catalytic activity. Stability of the best-performed catalyst has been tested in the two conditions, showing remarkable long-term stability and thermal stability, however, showed deactivation after thermally ageing at 700 °C. Copyright © 2020 BCREC Group. All rights reserved 

Sign in / Sign up

Export Citation Format

Share Document