scholarly journals Effect of Fiber Distribution on the Mechanical Behavior in Bending of Self-Compacting Mortars

2020 ◽  
Vol 15 (1) ◽  
pp. 129-148
Author(s):  
Lynda Kheddache ◽  
Kahina Chahour ◽  
Brahim Safi
Keyword(s):  
Tensile Strength ◽  
Mechanical Behavior ◽  
Lower Layer ◽  
Physical And Mechanical Properties ◽  
Steel Fibers ◽  
Fiber Distribution ◽  
Fiber Reinforced ◽  
Fiber Layer ◽  
Cementitious Matrix ◽  
Hardened State

Abstract The purpose of this work is to assess the steel fiber distribution effect on physical and mechanical properties of self-compacting mortar. An experimental study was conducted to see the fiber distribution during the implementation of self-compacting mortars that are fluid and on mechanical behavior in bending tensile strength. A method of placing self-compacting mortar in the molds has been developed to highlight the distribution of fibers in the cementitious matrix. The mortars are placed in prismatic molds in three layers. The amount of steel fibers differs from one layer to another. A total quantity of 90 kg /m3 was distributed in prismatic molds of dimensions 40x40x160 mm3. Straight and hooked ends steel fibers were used. The characteristics of mortars containing both types of fibers in the fresh and hardened state were measured and compared to those of self-compacting mortar without fibers. The pouring by layer allowed us to deduce that the distribution of metallic fibers has a significant effect on the hardened properties of the mortar. Indeed, the mechanical strength of the fiber-reinforced mortar depends on the nature and distribution of fibers in the cementitious matrix (mortar). A gain in bending tensile strength of 71.83% was recorded for self-compacting mortars elaborated with hooked end fibers and 52.11% for those containing straight steel fibers. Indeed, mortars containing entirely the same dosage of steel fibers (90 kg/m3) have a bending tensile strength that varies according to the fibers dosage by layers. Mortar samples with higher fiber content in the lower layer have a higher bending tensile strength than other samples with a higher fiber layer in the middle or layer above. However, it should be noted that steel fibers with hooks are much more effective than those without hooks. Indeed, the effect of fiber distribution is more significant for fibers without hooks because the hooks can slow down the movement of the fibers during the pouring of the mortar. The variation of the dosages per layer generated a difference in the deflection values for the mortars. The deflection is much higher for fiber-reinforced mortars (with hooks) compared to fiber-reinforced mortars without hooks.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Anodic and Mechanical Behavior of Carbon Fiber Reinforced Polymer as a Dual-Functional Material in Chloride-Contaminated Concrete

Materials ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 222
Author(s):  
Liangliang Wei ◽  
Ji-Hua Zhu ◽  
Zhijun Dong ◽  
Jun Liu ◽  
Wei Liu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Mechanical Behavior ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Functional Material ◽  
Dual Functional ◽  
Reinforced Polymer ◽  
Chloride Contaminated

Carbon fiber reinforced polymer (CFRP) has been used as a dual-functional material in a hybrid intervention system (ICCP-SS) which integrates the impressed current cathodic protection (ICCP) and structural strengthening (SS). The mechanical behavior of CFRP as an anode has been investigated in some solution environments. However, the anodic and mechanical behavior of CFRP bonded to concrete is unclear. This paper focuses on the anodic and mechanical performance of CFRP bonded to the chloride-contaminated concrete by conducting an electrochemical (EC) test. The method of bonding the CFRP to the concrete and the shape of the steel embedded in the concrete were considered. The current densities of 20 mA/m2 and 100 mA/m2 were applied during 120-day and 310-day EC tests. The electrode potentials and driving voltages were recorded, and the bond interfaces of the CFRP were inspected after EC test. The residual tensile strength and failure modes of the CFRP were analyzed after tensile tests. Finally, the long-term performance of CFRP as a dual-functional material in ICCP-SS system was discussed. Results show that the externally bonding CFRP in ICCP-SS system can not only protect the steel in chloride-contaminated concrete effectively but also maintain 70% of the original tensile strength of CFRP at a charge density of 744 A·h/m2. The expected service period of CFRP as a dual-functional material bonded to the chloride-contaminated concrete was determined to be more than 42.5 years.

Compressive Strength and Splitting Tensile Strength of Steel Fiber Reinforced Ultra High Strength Concrete (SFRC)

2010 ◽  
Vol 34-35 ◽  
pp. 1441-1444 ◽  
Author(s):  
Ju Zhang ◽  
Chang Wang Yan ◽  
Jin Qing Jia
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
Volume Fraction ◽  
High Strength ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Strength Concrete

This paper investigates the compressive strength and splitting tensile strength of ultra high strength concrete containing steel fiber. The steel fibers were added at the volume fractions of 0%, 0.5%, 0.75%, 1.0% and 1.5%. The compressive strength of the steel fiber reinforced ultra high strength concrete (SFRC) reached a maximum at 0.75% volume fraction, being a 15.5% improvement over the UHSC. The splitting tensile strength of the SFRC improved with increasing the volume fraction, achieving 91.9% improvements at 1.5% volume fraction. Strength models were established to predict the compressive and splitting tensile strengths of the SFRC. The models give predictions matching the measurements. Conclusions can be drawn that the marked brittleness with low tensile strength and strain capacities of ultra high strength concrete (UHSC) can be overcome by the addition of steel fibers.

scholarly journals The effect of saturation on the physical and mechanical behavior of some rock samples

2021 ◽  
Vol 2 (3) ◽  
pp. 23-31
Author(s):  
Mohammad Taghi Hamzaban
Keyword(s):  
Tensile Strength ◽  
Mechanical Behavior ◽  
Physical And Mechanical Properties ◽  
Intact Rock ◽  
P Wave ◽  
Mechanical Parameters ◽  
Brazilian Tensile Strength ◽  
Rock Samples ◽  
Rock Types ◽  
Major Factors

Different major factors control the strength of solid rocks. Moisture content is one of the most important factors, which can change the physical and mechanical behavior of intact rock as well as rock mass. Several early studies have shown that rock is weaker if tested wet rather than dry. In this paper, the density, P-wave velocity, uniaxial compressive strength, Brazilian tensile strength, and modulus of elasticity of seven different intact rock samples were measured under both dry and saturated conditions. The porosity of the samples was reported as well. Based on the obtained results, some correlations were proposed for estimating the saturated physical and mechanical properties from dry ones. The proposed correlations include different rock types and are more general than the previously reported ones. Comparing the obtained results showed that the mechanical and physical properties of weaker samples are more sensitive to the saturation process. Moreover, among the different mechanical parameters, Brazilian tensile strength exhibited more sensitivity to saturation. Comparing the results with the calculated porosities revealed that porosity is one of the key factors in the effect of saturation on physical and mechanical parameters. It seems that in the more porous rock samples, greater changes in the different measured parameters occur after saturation.

scholarly journals Steel fiber reinforced concrete pipes: part 1: technological analysis of the mechanical behavior

2012 ◽  
Vol 5 (1) ◽  
pp. 1-11 ◽  
Author(s):  
A. D. de Figueiredo ◽  
A. de la Fuente ◽  
A. Aguado ◽  
C. Molins ◽  
P. J. Chama Neto
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behavior ◽  
Steel Fiber ◽  
Test Procedure ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Test Procedures ◽  
Concrete Pipes

This paper is the first part of an extensive work focusing the technological development of steel fiber reinforced concrete pipes (FRCP). Here is presented and discussed the experimental campaign focusing the test procedure and the mechanical behavior obtained for each of the dosages of fiber used. In the second part ("Steel fiber reinforced concrete pipes. Part 2: Numerical model to simulate the crushing test"), the aspects of FRCP numerical modeling are presented and analyzed using the same experimental results in order to be validated. This study was carried out trying to reduce some uncertainties related to FRCP performance and provide a better condition to the use of these components. In this respect, an experimental study was carried out using sewage concrete pipes in full scale as specimens. The diameter of the specimens was 600 mm, and they had a length of 2500 mm. The pipes were reinforced with traditional bars and different contents of steel fibers in order to compare their performance through the crushing test. Two test procedures were used in that sense. In the 1st Series, the diameter displacement was monitored by the use of two LVDTs positioned at both extremities of the pipes. In the 2nd Series, just one LVDT is positioned at the spigot. The results shown a more rigidity response of the pipe during tests when the displacements were measured at the enlarged section of the socket. The fiber reinforcement was very effective, especially when low level of displacement was imposed to the FRCP. At this condition, the steel fibers showed an equivalent performance to superior class pipes made with traditional reinforced. The fiber content of 40 kg/m3 provided a hardening behavior for the FRCP, and could be considered as equivalent to the critical volume in this condition.

scholarly journals Evaluation of Selected Physicomechanical Properties of SFRC according to Different Standards

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Tereza Komárková ◽  
Jaromír Láník ◽  
Ondřej Anton
Keyword(s):  
Tensile Strength ◽  
Steel Fiber ◽  
Rapid Development ◽  
Physicomechanical Properties ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Building Site ◽  
Standards And Regulations ◽  
Strength In Bending

Steel fiber reinforced concretes are currently very popular, especially in the construction of industrial floors of warehouses and other halls with relatively large floor areas. However, it is important to mention that despite the rapid development of steel fiber reinforced concretes, the standards and regulations for their designing and testing have not been unified yet. This paper presents findings about the physicomechanical parameters of the steel fiber reinforced concretes manufactured by adding steel fibers into the truck mixer on the building site. The experimentally obtained results from the performed tests of tensile strength in bending according to various procedures are compared, and the suitability of the methods used is assessed according to these procedures.

Binary Superposition Mix Design Method for SFRC Part I: Principle and Evaluation

2010 ◽  
Vol 168-170 ◽  
pp. 2186-2190 ◽  
Author(s):  
Shun Bo Zhao ◽  
Hong Yuan Huo ◽  
Chen Xiao Song ◽  
Li Sha Song
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Cement Paste ◽  
Steel Fiber ◽  
Design Method ◽  
Splitting Tensile Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Mix Design ◽  
Fiber Reinforced

The binary superposition mix design method is constructed to quantitatively calculate the compositions of steel fiber reinforced concrete (SFRC), which brings into sufficient cement paste wrapping steel fibers to strengthen the boundary surfaces of steel fibers with base concrete. The principle of the method is firstly introduced. The experiments were carried out to evaluate the validity of the method. In the experiment, the cubic and axial compressive strength as well as the splitting tensile strength of SFRC affected by the fraction of steel fiber by volume and the average thickness of cement paste wrapping steel fibers were tested. The results are analyzed on the basis of former studies specified in the current technical specification for fiber reinforced concrete structures, which show that the larger strengths especial the splitting tensile strength of SFRC in grade CF50 can be got by the method, but the less splitting tensile strength of SFRC in grade of CF40 should be further studied.

scholarly journals Tensile Behavior of Self-Compacting Steel Fiber Reinforced Concrete Evaluated by Different Test Methods

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 251
Author(s):  
Xinxin Ding ◽  
Changyong Li ◽  
Minglei Zhao ◽  
Jie Li ◽  
Haibin Geng ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Tensile Test ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Axial Tensile ◽  
Splitting Tensile Test

Due to the mechanical properties related closely to the distribution of steel fibers in concrete matrix, the assessment of tensile strength of self-compacting steel fiber reinforced concrete (SFRC) is significant for the engineering application. In this paper, seven groups of self-compacting SFRC were produced with the mix proportion designed by using the steel fiber-aggregates skeleton packing test method. The hooked-end steel fibers with length of 25.1 mm, 29.8 mm and 34.8 mm were used, and the volume fraction varied from 0.4% to 1.4%. The axial tensile test of notched sectional prism specimen and the splitting tensile test of cube specimen were carried out. Results show that the axial tensile strength was higher than the splitting tensile strength for the same self-compacting SFRC, the axial tensile work and toughness was not related to the length of steel fiber. Finally, the equations for the prediction of tensile strength of self-compacting SFRC are proposed considering the fiber distribution and fiber factor, and the adaptability of splitting tensile test for self-compacting SFRC is discussed.

Performance on Steel Fiber Reinforced Self-Stressing Concrete

2008 ◽  
Vol 400-402 ◽  
pp. 427-432
Author(s):  
Huan An He ◽  
Bo Xin Wang ◽  
Jian Ting Lin
Keyword(s):  
Tensile Strength ◽  
Prestressed Concrete ◽  
High Performance ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
The Troubles ◽  
Steel Bars ◽  
Steel Fiber Concrete

In this paper a new sort of high performance concrete is introduced which combines most advantages of prestressed concrete and steel fiber concrete, named steel fiber reinforced self-stressing concrete(SFFRSSC for short). Self-stressing concrete is actually a kind of expansive concrete which self-stresses, namely pre-compressive stresses, are induced by dint of some restrictions generally provided by steel bars to concrete expansion after hydration of expansive cement. As a result of chemical reaction, concrete archived prestresses by itself different from mechanical prestressed concrete, so called self-stressing concrete. By distributing short-cut steel fibers into self-stressing concrete at random, self-stresses are generated in concrete under combined restriction of steel bars as well as steel fibers. Thank to the pre-stresses tensile strength of concrete are significantly increased as well as cracking strength. In addition, on the one hand, expansive deformation of SFFRSSC can compensate the shrinkage of concrete to decrease non-loaded cracks resulting from shrinkage, and even when cracking, the steel fibers play an important role in resistance to crack development. On the other hand, self-stressing concrete can avoid the troubles of construction compared with conventional mechanical prestressed concrete. Therefore, above-mentioned advantages of SFFRSSC over ordinary concrete imply a better prospect in using SFFRSSC in civil engineering. For purpose of understanding the properties of SFFRSSC, in this paper some researches were carried out to investigate the special expansive behaviors with ages and tensile strength. The test results indicated that at early age the expansion of SFFRSSC developed rapidly but 14 day the 90% of overall expansive deformation basically fulfilled and subsequently expansion kept stable. Axial tensile test result showed that tensile strength were improved 2-3 times for self-stressing concrete specimens restrained by steel bars as well as steel fibers.

scholarly journals HYBRID FIBER REINFORCED CONCRETE WITH POZZOLANIC MATERIALS

2020 ◽  
Vol 1 (1) ◽  
pp. 16-24
Author(s):  
Saeid Golizadeh Fard
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Bending Strength ◽  
Steel Fiber ◽  
Low Cost ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Micro Cracks ◽  
Pozzolanic Materials

This paper investigates the possibility of combining steel fibers with different weight percentages along with their functions in increasing compressive strength, indirect tensile strength and bending strength. It`s been considered an important economic issue for a long time the ability to service and increase the load-bearing capacity of structural materials. Concrete as a widely used structural material is widely used today. Despite its remarkable properties including high ductility, high durability, longevity, availability and low cost, concrete is a brittle material and performs extremely poor under flexural and tensile loads. In general, the breakdown and destruction of concrete is strongly dependent on the formation of cracks and micro-cracks. As the loading increases, the micro-cracks interconnect and form cracks. In order to address this problem and to create homogeneous conditions, a series of thin filaments has been used throughout the concrete in recent decades; They are called fibers. Steel fiber is one of the most commonly used fibers in concrete. In this study, the compressive strength of concrete was investigated which in some specimens reinforced with steel and containing pozzolanic materials, the compressive strength of control samples increased with the use of fiber etc. In the present study, the flexural and tensile strength of steel fiber reinforced specimens were investigated. According to the results, flexural strength increases with increase in steel fibers. The designs contain 1%, 1.5% and 2% of the Dramix hooked steel fibers used in the research. By reinforcing the specimens with steel fibers, the behavior of tensile concrete is much more flexible than that of non-steel specimens.

Sign in / Sign up

Export Citation Format

Share Document