scholarly journals Highly Productive Tools For Turning And Milling

2015 ◽  
Vol 12 (2) ◽  
pp. 5-9
Author(s):  
Karol Vasilko
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Considerable Influence ◽  
Machined Surface ◽  
Machined Surface Quality ◽  
Surface Microgeometry ◽  
Tip Radius ◽  
Machining Productivity ◽  
The Relationship

Abstract Beside cutting speed, shift is another important parameter of machining. Its considerable influence is shown mainly in the workpiece machined surface microgeometry. In practice, mainly its combination with the radius of cutting tool tip rounding is used. Options to further increase machining productivity and machined surface quality are hidden in this approach. The paper presents variations of the design of productive cutting tools for lathe work and milling on the base of the use of the laws of the relationship among the highest reached uneveness of machined surface, tool tip radius and shift.

scholarly journals Metallurgical and Machinability Characteristics of Wrought and Selective Laser Melted Ti-6Al-4V

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Manikandakumar Shunmugavel ◽  
Ashwin Polishetty ◽  
Junior Nomani ◽  
Moshe Goldberg ◽  
Guy Littlefair
Keyword(s):  
Tool Wear ◽  
Cutting Tool ◽  
Flank Wear ◽  
Research Work ◽  
Cutting Speed ◽  
Machined Surface ◽  
Machined Surface Quality ◽  
Coating Delamination ◽  
All Speeds ◽  
Cutting Speeds

This research work presents a machinability study between wrought grade titanium and selective laser melted (SLM) titanium Ti-6Al-4V in a face turning operation, machined at cutting speeds between 60 and 180 m/min. Machinability characteristics such as tool wear, cutting forces, and machined surface quality were investigated. Coating delamination, adhesion, abrasion, attrition, and chipping wear mechanisms were dominant during machining of SLM Ti-6Al-4V. Maximum flank wear was found higher in machining SLM Ti-6Al-4V compared to wrought Ti-6Al-4V at all speeds. It was also found that high machining speeds lead to catastrophic failure of the cutting tool during machining of SLM Ti-6Al-4V. Cutting force was higher in machining SLM Ti-6Al-4V as compared to wrought Ti-6Al-4V for all cutting speeds due to its higher strength and hardness. Surface finish improved with the cutting speed despite the high tool wear observed at high machining speeds. Overall, machinability of SLM Ti-6Al-4V was found poor as compared to the wrought alloy.

Evaluation of Surface Integrity during Machining with Different Tool Grades of Sicp/Al-Si Composites Produced by Powder Metallurgy

2011 ◽  
Vol 672 ◽  
pp. 319-322 ◽  
Author(s):  
Mustafa Günay ◽  
Ulvi Şeker
Keyword(s):  
Surface Roughness ◽  
Powder Metallurgy ◽  
Surface Integrity ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Machining Process ◽  
Machined Surface ◽  
Alloy Matrix ◽  
Surface Finishes

MMCs components are mostly produced using near net shape manufacturing methods and are subsequently machined to the final dimensions and surface finishes. The MMCs consist of extremely hard reinforcing particles and pose considerable challenges due to the poor machinability and severe wear of the cutting tool. In this study, cutting performance of WC, CBN and PCD cutting tools were investigated with respect to surface roughness during machining of 10 wt % SiCp reinforced Al-Si alloy matrix composites produced by powder metallurgy (PM) method. Average surface roughness (Ra) corresponding to each machining condition was measured. After the machining process the worn insert tips were examined under the scanning electron microscope (SEM). Chip geometry and machined surface photographs have been taken by optical microscopy. The experimental results showed that surface roughness decreased with increasing cutting speed for all of cutting tool materials. The best surface integrity was occurred after the machining with PCD insert at the highest cutting speed employed.

Experimental Investigations into Machining of FRP Material

2016 ◽  
Vol 836-837 ◽  
pp. 29-35
Author(s):  
Pavel Zeman ◽  
Petr Kolar ◽  
Petr Masek
Keyword(s):  
Surface Quality ◽  
Cutting Forces ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cellulose Fibre ◽  
Experimental Investigations ◽  
Tool Geometry ◽  
Machined Surface ◽  
Milling Operations ◽  
Machined Surface Quality

Machining of fibre-reinforced thermosets is becoming a very popular technology today. Nevertheless, machinability of these materials is rather different from conventional materials such as metals since hard and abrasive fibres are combined with relatively soft resin with low glass transition temperature. Special attention has to be given to workpiece quality because delamination and burning of machined surface can occur. An experimental investigation into machinability of a polymeric and cellulose fibre-reinforced resin material was carried out. Milling operations were inspected with respect to process temperature, cutting forces and machined surface quality. The effect of cutting conditions on the mentioned aspects was determined. Standard and tailored cutting tools were used in the investigation. It was observed that surface quality is strongly dependent on tool geometry, milling strategy, fibre orientation and feed. On the other hand, cutting forces are relatively low and dependent on tool geometry and feed. The modified cutting tool with more positive tool geometry showed better results compared to the conventional one.

Study on the Cutting Force and Machined Surface Quality of Milling AFRP

2016 ◽  
Vol 836-837 ◽  
pp. 155-160 ◽  
Author(s):  
Si Qi Liu ◽  
Yan Chen ◽  
Yu Can Fu ◽  
An Dong Hu
Keyword(s):  
Cutting Force ◽  
Surface Quality ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Helix Angle ◽  
End Mill ◽  
Machined Surface ◽  
Reinforced Plastics ◽  
Machined Surface Quality

AFRP(Aramid Fiber Reinforced Plastics) is widely used in the aerospace and automotive while there are many problems in machining AFRP such as furry, delamination, burns and so on. Milling experiments of AFRP have been conducted to study the influence of different helix angle (0°, 30°, 60°) and cutting tools (traditional end mill, multiple flute end mill and compression end mill) on cutting force and machined surface quality. The results indicated that the cutting force has been reduced and the surface quality has been improved with the increase of helix angle. The cutting tool structure can make greater influence on machined surface quality than the cutting parameters. A cutting tool with the structure of multiple flute or herringbone cutting edge could reduce the axial cutting force. However the cutting force is too small to cut off fibers when using a multiple flute end mill. A good processing surface can be achieved while cutting with a compression end mill or a tool with big helix angle.

Estimation of Possibilities of the Productivity Rise at Turning of Hard-Processing Materials

2014 ◽  
Vol 657 ◽  
pp. 63-67
Author(s):  
Tatiana Ivchenko ◽  
Vadim Boguslavskiy ◽  
Irina Petryaeva ◽  
Dmitriy Mihaylov
Keyword(s):  
Surface Roughness ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Machined Surface ◽  
Machined Surface Roughness ◽  
Cutting Regimes ◽  
Machining Productivity ◽  
Coated Carbide

The Method of Estimation of Possibilities of the Machining Productivity Rise Taking into Account the Action of Cutting Fluid (TCF) and Coated Carbide Cutting Tools (CCT) for Rough and Fin-Ish Turning Corrosion-Proof, Heat Resisting and Stainless Steels and Alloys is Perfected. the Factor of Machining Productivity Rise at the Expense of Use TCF and CCT is Set. it is Executed Theoretical and Experimental Researches of Influence of the Cutting Regimes on the Cutting Temperature and the Ma-Chined Surface Roughness at Turning of Different Hard-Processing Steels and Alloys. Dependences of the Cutting Temperature and the Machined Surface Roughness on Cutting Speed, Feed and Depth Taking into Account the Action of TCF and CCT are Set. the Factors of Decline of the Machined Surface Roughness and the Cutting Temperature are Certain at the Use of TCF with Different Cooling and Lubri-Cant Properties. the Factors of Machining Productivity Rise are Certain under Various Conditions of the Rough and Finish Turning Different Corrosion - Proof, Heat Resisting and High - Resistance Steels and Alloys Depending on the Factor of the Cutting Temperature Decline and Factor of the Tool Life Rise. the Set Factor of Machining Productivity Rise Allows Estimating Efficiency of the Use of Various TCF and CCT for Different Hard-Processing Materials.

scholarly journals Feasibility of Cobalt-Free Nanostructured WC Cutting Inserts for Machining of a TiC/Fe Composite

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3432
Author(s):  
Edwin Gevorkyan ◽  
Mirosław Rucki ◽  
Tadeusz Sałaciński ◽  
Zbigniew Siemiątkowski ◽  
Volodymyr Nerubatskyi ◽  
...  
Keyword(s):  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Machined Surface ◽  
Powder Consolidation ◽  
Plasma Sintering ◽  
Cutting Inserts ◽  
Spark Plasma ◽  
And Performance ◽  
Nanostructured Tungsten Carbide

The paper presents results of investigations on the binderless nanostructured tungsten carbide (WC) cutting tools fabrication and performance. The scientific novelty includes the description of some regularities of the powder consolidation under electric current and the subsequent possibility to utilize them for practical use in the fabrication of cutting tools. The sintering process of WC nanopowder was performed with the electroconsolidation method, which is a modification of spark plasma sintering (SPS). Its advantages include low temperatures and short sintering time which allows retaining nanosize grains of ca. 70 nm, close to the original particle size of the starting powder. In respect to the application of the cutting tools, pure WC nanostructure resulted in a smaller cutting edge radius providing a higher quality of TiC/Fe machined surface. In the range of cutting speeds, vc = 15–40 m/min the durability of the inserts was 75% of that achieved by cubic boron nitride ones, and more than two times better than that of WC-Co cutting tools. In additional tests of machining 13CrMo4 material at an elevated cutting speed of vc = 100 m/min, binderless nWC inserts worked almost three times longer than WC-Co composites.

Hard Nano-Crystalline Coatings for Cutting Tools

2007 ◽  
Vol 567-568 ◽  
pp. 185-188 ◽  
Author(s):  
Miroslav Piska
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Dry Cutting ◽  
Nano Crystalline ◽  
The Right ◽  
Machining Productivity ◽  
Hard Cutting ◽  
Cutting Tool Materials

Modern trends in metal cutting, high speed/feed machining, dry cutting and hard cutting set more demanding characteristics for cutting tool materials. The exposed parts of the cutting edges must be protected against the severe loading conditions and wear. The most significant coatings methods for cutting tools are PVD and CVD/MTCVD today. The choice of the right substrate or the right protective coating in the specific machining operation can have serious impact on machining productivity and economy. In many cases the deposition of the cutting tool with a hard coating increases considerably its cutting performance and tool life. The coating protects the tool against abrasion, adhesion, diffusion, formation of comb cracks and other wear phenomena.

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

Microtexture Generation Using Controlled Chatter Machining in Ultraprecision Diamond Turning

2015 ◽  
Vol 3 (2) ◽  
Author(s):  
Syed Adnan Ahmed ◽  
Jeong Hoon Ko ◽  
Sathyan Subbiah ◽  
Swee Hock Yeo
Keyword(s):  
Cutting Tool ◽  
Cutting Speed ◽  
Diamond Turning ◽  
Diamond Cutting ◽  
Machined Surface ◽  
Excited Vibration ◽  
Mass And Heat Transfer ◽  
Tool Shank ◽  
Diamond Cutting Tool

This paper describes a new method of microtexture generation in precision machining through self-excited vibrations of a diamond cutting tool. Conventionally, a cutting tool vibration or chatter is detrimental to the quality of the machined surface. In this study, an attempt is made to use the cutting tool's self-excited vibration during a cutting beneficially to generate microtextures. This approach is named as “controlled chatter machining (CCM).” Modal analysis is first performed to study the dynamic behavior of the cutting tool. Turning processes are then conducted by varying the tool holder length as a means to control vibration. The experimental results indicate that the self-excited diamond cutting tool can generate microtextures of various shapes, which depend on the cutting tool shank, cutting speed, feed, and cutting depth. The potential application of this proposed technique is to create microtextures in microchannels and microcavities to be used in mass and heat transfer applications.

Sign in / Sign up

Export Citation Format

Share Document