Characterisation of the Humming-Type Noise and Vibration of the Automotive HVAC System

2019 ◽  
Vol 16 (2) ◽  
pp. 6634-6648
Author(s):  
A. Z. A. Mazlan ◽  
M. H. A. Satar ◽  
M. H. Hamdan ◽  
M. S. Md. Isa ◽  
S. Man ◽  
...  
Keyword(s):  
Vibration Characteristics ◽  
Operating Conditions ◽  
Hvac System ◽  
Frequency Range ◽  
Noise And Vibration ◽  
Power Steering ◽  
Pump Compressor

The automotive heating and ventilating air condition (HVAC) system, when vibrating, can generate various types of noises such as humming, hissing, clicking and air-rushes. These noises can be characterised to determine their root causes. In this study, the humming-type noise is taken into consideration whereby the noise and vibration characteristics are measured from various HVAC components such as power steering pump, compressor and air conditional pipe. Four types of measurement sensors were used in this study - tachometer for rpm tracking; accelerometer for the vibration microphone for the noise; and sound camera for the visualization measurement. Two types of operating conditions were taken into consideration - they were “idle” (850 rpm) and “running” (850-1400 rpm) conditions. A constant blower speed was applied for both conditions. The result shows that the humming noises can be determined at the frequency range of 300-350 Hz and 150-250 Hz for both idle and running conditions, respectively. The vibration of the power steering pump shows the worst acceleration of 1.8 m/s2 at the frequency range of 150-250 Hz, compared to the compressor and air conditional pipe. This result was validated with the 3D colour order and sound camera analyses, in which the humming noise colour mapping shows dominance in this frequency range.  

scholarly journals Measurement of the Hissing-Type Noise and Vibration of the Automotive HVAC System

2018 ◽  
Vol 217 ◽  
pp. 03002
Author(s):  
Muhammad Abdul Rahman Paiman ◽  
Ahmad Zhafran Ahmad Mazlan ◽  
Muhammad Hidayat Hamdan ◽  
Mohamad Syazwan Md. Isa ◽  
Sharum Man ◽  
...  
Keyword(s):  
Thermal Expansion ◽  
Common Type ◽  
Operating Conditions ◽  
Noise Measurement ◽  
Hvac System ◽  
Frequency Range ◽  
Noise And Vibration ◽  
Root Cause ◽  
Expansion Valve ◽  
The Common

Noises such as hissing, humming, air-rush and compressor engagement are the common type of noises that can be induced from the automotive heating and ventilating air conditional (HVAC) system. These noises are basically generated from the effects of vibrational HVAC components. Due to this, the root cause of the noises has to be investigated for any implementation of solution. In this study, the hissing-type of noise is taken into consideration whereby the noise and vibration are measured from various HVAC components such as Evaporator Inlet and Outlet and Thermal Expansion Valve (TXV). Three types of measurement sensors are used in this study which is tri-axial accelerometer for the vibration, tachometer for the engine rpm tracking and microphone for the noise measurement. Two types of operating conditions are taken into consideration, when engine running at 850 rpm (idle) and 850-3000 rpm (tracking) conditions and a constant blower speed is applied for both conditions. the result shows that, the hissing type of noise is determined at the frequency range of 4500-5000 Hz for the both idle and running conditions, whereby the vibration at the Evaporator Inlet is the most significant compared to the Evaporator Core and TVX components. the vibration of the Evaporator Inlet shows the drastic vibration increment between 1000-1500 rpm and getting worse towards 3000 rpm. This result is validated with the 3D colour of noise waterfall analysis, whereby the hissing noise shows the dominant result in the frequency range of 4500-5000 Hz.

Validation of Clicking-type Noise and Vibration in Automotive HVAC System

2021 ◽  
Vol 18 (1) ◽  
Author(s):  
M.H.A. Satar ◽  
A. Z. A. Mazlan ◽  
M.H. Hamdan ◽  
M.S. Md. Isa ◽  
M.A.R. Paiman ◽  
...  
Keyword(s):  
Scale Model ◽  
Hvac System ◽  
Frequency Range ◽  
Similar Frequency ◽  
Noise And Vibration ◽  
System A ◽  
Vehicle System ◽  
Operating Frequency Range ◽  
Expansion Valve ◽  
Good Agreement

In this study, the characteristics of clicking-type noise and vibration occurring in the automotive heating, ventilation and air conditional (HVAC) systems are investigated. A lab-scale model of HVAC system is developed, and validation is carried out with a vehicle system. A fixed blower speed of 1 (at an airflow of 2.53 m/s) with alternated air conditional (AC) was implied in this study. Three different sensors namely as tachometer, accelerometer, and microphone were used to measure and prove the existing noise in the HVAC system. The study inferred that the compressor contributed significantly to the total vibration and noise in the HVAC system. Other components such as AC pipe, evaporator, and thermal expansion valve (TXV) also contributed to a slight extent. The clicking noise was observed in the operating frequency range of 200 ~ 300 Hz. This noise and vibration issues are partly influenced by the running conditions of the AC and the effect was significant when the AC was turned on. The validation of the findings in the model shows a good agreement with the results obtained in the vehicle system, whereby the clicking noise and vibration can be observed at a similar frequency range.

Quantification of aerodynamically induced noise and vibration-induced noise in a suction unit

2011 ◽  
Vol 225 (3) ◽  
pp. 617-624 ◽  
Author(s):  
J Prezelj ◽  
M Čudina
Keyword(s):  
Transfer Function ◽  
Noise Reduction ◽  
Noise Source ◽  
Operating Conditions ◽  
Frequency Range ◽  
Centrifugal Blower ◽  
Noise Sources ◽  
Noise And Vibration ◽  
Different Types ◽  
The Individual

Noise, generated by a centrifugal blower, can be divided according to its origin, into aerodynamically induced noise and vibration-induced noise. The contribution of the individual noise source to the total emitted noise is hard to determine, but it is crucial for the design of noise reduction measures. In order to reduce the noise of the centrifugal blower in a broad range of operating conditions, an identification of noise sources needs to be performed. An analysis of the most important noise origin in a centrifugal blower presented in this article was performed by measurements of the transfer function between noise and vibration, under different types of excitation. From the analyses one can conclude that the dominant noise source of a centrifugal blower can be attributed to the aerodynamically generated noise which exceeds the vibration-induced noise for more than 10 dB in a broad frequency range.

Fabrication and finite element analysis of vibrating parallel film actuator made with cellulose acetate for potential haptic application

2016 ◽  
Vol 230 (15) ◽  
pp. 2720-2727 ◽  
Author(s):  
Md Mohiuddin ◽  
Asma Akther ◽  
Eun Byul Jo ◽  
Hyun Chan Kim ◽  
Jaehwan Kim
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cellulose Acetate ◽  
Vibration Characteristics ◽  
Experimental Results ◽  
Vibration Velocity ◽  
Frequency Range ◽  
Actuation Frequency ◽  
Element Analysis ◽  
Wide Range

The present study investigates a film actuator made with dielectric cellulose acetate films separated by narrow spacers as a means of electrostatic actuation for potential haptic application. Fabrication process for the actuator is explained along with experiments conducted over a wide frequency range of actuation frequency. A valid finite element simulation of the actuator is made on the quarter section of the actuator by using full 3D finite elements. Vibration characteristics such as fundamental natural frequency, mode shape and output velocity in the frequency range for haptic feeling generation are obtained from the finite element analysis and compared with the experimental results. Experimental results demonstrate that the finite element model is practical and effective enough in predicting the vibration characteristics of the actuator for haptic application. The film actuator shows many promising properties like high transparency, wide range of actuation frequency and high vibration velocity for instance.

Flow Response of an Industrial Gas Turbine Combustor To Acoustic Forcing Extracted From Unforced Data

2021 ◽  
Author(s):  
Jan Paul Beuth ◽  
Jakob G. R. von Saldern ◽  
Thomas Ludwig Kaiser ◽  
Thoralf G. Reichel ◽  
Christian Oliver Paschereit ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Flow Dynamics ◽  
Low Rank ◽  
Frequency Range ◽  
Flow Response ◽  
Flow Fluctuations ◽  
Flame Dynamics ◽  
Flame Response ◽  
Acoustic Forcing

Abstract Gas turbine combustors are commonly operated with lean premix flames, allowing for high efficiencies and low emissions. These operating conditions are susceptible to thermoacoustic pulsations, originating from acoustic-flame coupling. To reveal this coupling, experiments or simulations of acoustically forced combustion systems are necessary, which are very challenging for real-scale applications. In this work we investigate the possibility to determine the flame response to acoustic forcing from snapshots of the unforced flow. This approach is based on three central hypothesis: first, the flame response is driven by flow fluctuations, second, these flow fluctuations are dominated by coherent structures driven by hydrodynamic instabilities, and third, these instabilities are driven by stochastic forcing of the background turbulence. As a consequence the dynamics in the natural flow should be low-rank and very similar to those of the acoustically forced system. In this work, the methodology is applied to experimental data of an industry-scale swirl combustor. A resolvent analysis is conducted based on the linearized Navier-Stokes equations to assure analytically the low-rank behavior of the flow dynamics. Then, these dynamics are extracted from flow snapshots using spectral proper orthogonal decomposition (SPOD). The extended SPOD is applied to determine the heat release rate fluctuations that are correlated with the flow dynamics. The low-rank flow and flame dynamics determined from the analytic and data-driven approach are then compared to the flow response determined from a classic phase average of the acoustically forced flow, which allow the research hypothesis to be evaluated. It is concluded that for the present combustor, the flow and flame dynamics are low-rank for a wider frequency range and the response to harmonic forcing can be determined quite accurately from unforced snapshots. The methodology further allows to isolate the frequency range where the flame response is predominantly driven by hydrodynamic instabilites.

Design and simulation of Helmholtz resonator assembly used to attenuate tire acoustic cavity resonance noise

2021 ◽  
Vol 263 (6) ◽  
pp. 942-953
Author(s):  
Wei Zhao ◽  
Xiandong Liu ◽  
Yingchun Shan ◽  
Tian He
Keyword(s):  
Natural Frequencies ◽  
Helmholtz Resonator ◽  
Operating Conditions ◽  
Cavity Resonance ◽  
Frequency Range ◽  
Sound Fields ◽  
Acoustic Cavity ◽  
The Poor ◽  
Alloy Wheel ◽  
Reduction Effect

Tire acoustic cavity resonance noise (TACRN) is a typical annoying lower-frequency interior noise of a passenger car. The widely used attenuating method of attaching the porous sound absorption material in tire cavity can reduce TACRN effectively, but causes the increase of tire-wheel assembly weight and cost, also the poor durability. Additionally, the Helmholtz resonator (HR) is also used in the wheel of some cars although having only narrow effective band. The existing investigation shows that the frequency of TACRN varies with the car speed and load and also has the split characteristics. The change of TACRN frequency causes a certain difficulty to suppress TACRN effectively. Aiming at this problem, in this paper, TACRN frequency range of a specific tire cavity under different operating conditions is first calculated and analyzed. Then, for a specific aluminum alloy wheel, a HR assembly including several HRs is designed to make the natural frequencies of HR assembly cover the TACRN frequencies. Finally, the reduction effect of TACRN is simulated and evaluated by comparing the sound fields in tire cavity with/without HR assembly under same volume velocity sound source. This work is helpful for attenuating TACRN effectively under the changing operating conditions.

Sign in / Sign up

Export Citation Format

Share Document