Performance of a small-size two-stage centrifugal compressor

2012 ◽  
pp. 307-318 ◽  
Author(s):  
R. Numakura
Keyword(s):  
Centrifugal Compressor ◽  
Two Stage

Numerical Analysis Techniques and Flow Characteristics of Two-Stage Centrifugal Compressor for R134a Turbo-Chiller

2007 ◽  
Vol 10 (4) ◽  
pp. 29-38
Author(s):  
Han-Young Park ◽  
Hyun-Taek Oh ◽  
You-Hwan Shin ◽  
Yoon-Pyo Lee ◽  
Kwang-Ho Kim ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Centrifugal Compressor ◽  
Flow Characteristics ◽  
Two Stage ◽  
Analysis Techniques

scholarly journals Pressure and Temperature Distortion Testing of a Two-Stage Centrifugal Compressor

1993 ◽  
Author(s):  
W. T. Cousins ◽  
K. K. Dalton ◽  
T. T. Andersen ◽  
G. A. Bobula
Keyword(s):  
Centrifugal Compressor ◽  
Two Stage ◽  
Test Setup ◽  
Inlet Distortion ◽  
Testing Techniques ◽  
Temperature And Pressure

Altitude pressure and temperature inlet distortion testing of the two-stage centrifugal compressor in the T800-LHT-800 engine is described. The test setup and the testing techniques are reviewed and the results of the test are presented. The generation of classical 180 degree patterns of both pressure and temperature distortion is discussed. Temperature distortion was created using a hydrogen burner system while pressure distortion was created in the classical manner, using screens. Results of both individual and combined temperature and pressure distortions in both opposed and concurrent patterns are shown.

Delay of Rotating Stall in Compressors Using Plasma Actuators

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Farzad Ashrafi ◽  
Mathias Michaud ◽  
Huu Duc Vo
Keyword(s):  
Centrifugal Compressor ◽  
Leading Edge ◽  
Plasma Actuator ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Compressor Stage ◽  
Dbd Plasma ◽  
Two Stage ◽  
Stall Inception ◽  
Flow Acceleration

Rotating stall is a well-known aerodynamic instability in compressors that limits the operating envelope of aircraft gas turbine engines. An innovative method for delaying the most common form of rotating stall inception using an annular dielectric barrier discharge (DBD) plasma actuator had been proposed. A DBD plasma actuator is a simple solid-state device that converts electricity directly into flow acceleration through partial air ionization. However, the proposed concept had only been preliminarily evaluated with numerical simulations on an isolated axial rotor using a relatively basic CFD code. This paper provides both an experimental and a numerical assessment of this concept for an axial compressor stage as well as a centrifugal compressor stage, with both stages being part of a low-speed two-stage axial-centrifugal compressor test rig. The two configurations studied are the two-stage configuration with a 100 mN/m annular casing plasma actuator placed just upstream of the axial rotor leading edge (LE) and the single-stage centrifugal compressor with the same actuator placed upstream of the impeller LE. The tested configurations were simulated with a commercial RANS CFD code (ansys cfx) in which was implemented the latest engineering DBD plasma model and dynamic throttle boundary condition, using single-passage multiple blade row computational domains. The computational fluid dynamics (CFD) simulations indicate that in both types of compressors, the actuator delays the stall inception by pushing the incoming/tip clearance flow interface downstream into the blade passage. In each case, the predicted reduction in stalling mass flow matches the experimental value reasonably well.

scholarly journals Design and Analysis of a Split Deswirl Vane in a Two-Stage Refrigeration Centrifugal Compressor

2014 ◽  
Vol 6 ◽  
pp. 130925 ◽  
Author(s):  
Jeng-Min Huang ◽  
Yue-Hann Tsai
Keyword(s):  
Centrifugal Compressor ◽  
Rotation Angle ◽  
Guide Vane ◽  
Low Flow ◽  
Working Fluid ◽  
Inlet Guide Vane ◽  
Two Stage ◽  
Double Row ◽  
Second Stage ◽  
Better Than

This study numerically investigated the influence of using the second row of a double-row deswirl vane as the inlet guide vane of the second stage on the performance of the first stage in a two-stage refrigeration centrifugal compressor. The working fluid was R134a, and the turbulence model was the Spalart-Allmaras model. The parameters discussed included the cutting position of the deswirl vane, the staggered angle of two rows of vane, and the rotation angle of the second row. The results showed that the performance of staggered angle 7.5° was better than that of 15° or 22.5°. When the staggered angle was 7.5°, the performance of cutting at 1/3 and 1/2 of the original deswirl vane length was slightly different from that of the original vane but obviously better than that of cutting at 2/3. When the staggered angle was 15°, the cutting position influenced the performance slightly. At a low flow rate prone to surge, when the second row at a staggered angle 7.5° cutting at the half of vane rotated 10°, the efficiency was reduced by only about 0.6%, and 10% of the swirl remained as the preswirl of the second stage, which is generally better than other designs.

A CFD Analysis of the Effects of Two-Phase Flow in a Two-Stage Centrifugal Compressor

2015 ◽  
Author(s):  
Chaitanya V. Halbe ◽  
Walter F. O’Brien ◽  
William T. Cousins ◽  
Vishnu Sishtla
Keyword(s):  
Centrifugal Compressor ◽  
Two Phase Flow ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Power Input ◽  
Phase Flow ◽  
Two Stage ◽  
Two Phase ◽  
Droplet Dynamics ◽  
Compressor Performance

The performance of a compressor is known to be affected by the ingestion of liquid droplets. Heat, mass and momentum transfer as well as the droplet dynamics are some of the important mechanisms that govern the two-phase flow. This paper presents numerical investigations of three-dimensional two-phase flow in a two-stage centrifugal compressor, incorporating the effects of the above mentioned mechanisms. The results of the two-phase flow simulations are compared with the simulation involving only the gaseous phase. The implications for the compressor performance, viz. the pressure ratio, the power input and the efficiency are discussed. The role played by the droplet-wall interactions on the rate of vaporization, and on the compressor performance is also highlighted.

A Numerical Study on the Effect of Inter-Stage Water Injection in an Opposed-Setting-Two-Stage Centrifugal Compressor

2020 ◽  
Author(s):  
Ming Ni ◽  
Shaojuan Geng ◽  
Zuojun Wei ◽  
Xiaohua Gan
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Water Injection ◽  
Two Stage ◽  
Stall Margin ◽  
Injection Parameter ◽  
Insufficient Time ◽  
The Stability ◽  
The Right

Abstract Inter-stage water injection is currently a common method to reduce the compression work. In this paper, we evaluate the effect of this approach on an opposed-setting-two-stage centrifugal compressor which is designed for a small gas turbine numerically. The Eulerian-Lagrangian method is adopted to calculate the continuous flow field and discrete particle terms with the k-ε turbulence model. 6 water injection conditions are conducted to compare with the dry air condition. The performance curve shift to the right-up side, i.e. higher total pressure ratio, higher efficiency and larger choking mass flow. However, the larger the performance improvement gained by inter-stage injection, the worse the stability will be. Under the micro injection ratio (about 0.1%), the stall margin of the compressor is improved. Additionally, with a proper injection parameter, the loading in the diffuser can be reduced and promise a wider stall margin. Nevertheless, there still exists droplets at the outlet of the high-pressure diffuser because of the insufficient time for evaporation.

Measured Performance of Two-Stage Centrifugal Compressor Under Wet Gas Conditions

2012 ◽  
Author(s):  
Matteo Bertoneri ◽  
Simone Duni ◽  
David Ransom ◽  
Luigi Podestà ◽  
Massimo Camatti ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Oil And Gas ◽  
Pressure Ratio ◽  
Oil And Gas Industry ◽  
Liquid Volume ◽  
Performance Measurements ◽  
Two Stage ◽  
Gas Industry ◽  
Discharge Temperature ◽  
Wet Gas

The oil and gas industry is moving forward to access the most remote gas reserves and enhance the exploitation of the existing installation or postponing their tail-end. To achieve these accomplishments several technology challenges are being unveiled. In topside upstream application both offshore and onshore, one important technology issue is the capability to compress gas with a significant amount of liquids and it assumes a special interest in case of the facilities revamping. Nevertheless is in the subsea environment where this technology issue becomes really challenging. In order to properly design and size a compressor/motor system for subsea wet gas compression, one must be able to adequately predict the compressor performance with mixed phase flow. This paper presents the results from an experimental test program which investigated the performance of a centrifugal compressor at various wet gas conditions with elevated suction pressure. Performance tests are completed on a two stage centrifugal compressor with a mixture of air and water at suction pressures of 20 bar (300 psi). The compressor is subjected to flow with liquid volume fractions ranging from 0 to 5% along three speedlines. The performance measurements are made in accordance with ASME PTC-10 specifications with an additional torque measurement on the shaft between the compressor and gearbox. At each test condition, once the liquid is injected in the air flow, an increase in pressure ratio occurs. This testifies the compressor is still able to work in presence of water. However, increasing the amount of liquid injected a decreased polytropic head together with an increased absorbed actual power by the compressor cause a deterioration of its efficiency. Moreover when liquid is introduced into the flow, the discharge temperature of the compressor reduces significantly. The performance results and trends mentioned above are reviewed in the detail in this paper.

scholarly journals Design and Development of an Advanced Two-Stage Centrifugal Compressor

1994 ◽  
Author(s):  
D. L. Palmer ◽  
W. F. Waterman
Keyword(s):  
Centrifugal Compressor ◽  
High Performance ◽  
Low Cost ◽  
Pressure Ratio ◽  
Tip Clearance ◽  
Development Effort ◽  
Design And Development ◽  
Two Stage ◽  
Surge Margin ◽  
The Impact

This paper describes the aero-mechanical design and development of a 3.3 kg/sec (7.3 lb/sec), 14:1 pressure ratio two-stage centrifugal compressor which is used in the T800-LHT-800 helicopter engine. The design employs highly nonradial, splitter bladed impellers with swept leading edges and compact vaned diffusers to achieve high performance in a small and robust configuration. The development effort quantified the effects of impeller diffusion and passive inducer shroud bleed on surge margin as well as the effects of impeller loading on tip clearance sensitivity and the impact of sand erosion and shroud roughness on performance. The developed compressor exceeded its performance objectives with a minimum of 23-percent surge margin without variable geometry. The compressor provides a high performance, rugged, low-cost configuration ideally suited for helicopter applications.

Sign in / Sign up

Export Citation Format

Share Document