scholarly journals Changes in the physicochemical characteristics of peanut straw biochar after freeze-thaw and dry-wet aging treatments of the biomass

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 4329-4343
Author(s):  
Yongqiang Cao ◽  
Yande Jing ◽  
Hao Hao ◽  
Xuan Wang
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
Pyrolysis Temperature ◽  
Ph Value ◽  
Aging Treatment ◽  
Physicochemical Characteristics ◽  
Freeze Thaw ◽  
Peanut Straw

Effects of aging after pyrolysis were tested relative to the physicochemical characteristics of peanut straw biochar. Biochar was prepared at pyrolysis temperatures of 350 °C, 500 °C, and 650 °C; then, it was freeze-thawed and dry-wet aged. The physicochemical characteristics of the fresh and aged biochar were analyzed. The results showed that the pyrolysis temperature, ambient temperature, and humidity affected the physicochemical characteristics of the biochar. With the increase of pyrolysis temperature, the yield and surface acidic functional groups of the fresh biochar decreased, whereas the ash content, C content, pH, specific surface area, and mesoporous volume of the fresh biochar increased. The aging treatment increased the acidic functional groups content in the biochar and reduced the aromatic functional groups content, which decreased the pH value of the biochar. The aging treatment increased the specific surface area and pore volume of the biochar, and the effect of freeze-thaw aging was greater than that of dry-wet aging. The aging treatment also destroyed the complete shape of the fresh biochar, and reduced its stability. After the aging treatment, the C content of the biochar decreased, whereas the O content increased, due to oxidation of the biochar.

scholarly journals Feedstock choice, pyrolysis temperature and type influence biochar characteristics: a comprehensive meta-data analysis review

Biochar ◽  
2020 ◽  
Vol 2 (4) ◽  
pp. 421-438
Author(s):  
James A. Ippolito ◽  
Liqiang Cui ◽  
Claudia Kammann ◽  
Nicole Wrage-Mönnig ◽  
Jose M. Estavillo ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pyrolysis Temperature ◽  
Chemical Properties ◽  
Soil Nutrient ◽  
Nutrient Retention ◽  
Nutrient Content ◽  
Physicochemical Characteristics ◽  
Minor Role

AbstractVarious studies have established that feedstock choice, pyrolysis temperature, and pyrolysis type influence final biochar physicochemical characteristics. However, overarching analyses of pre-biochar creation choices and correlations to biochar characteristics are severely lacking. Thus, the objective of this work was to help researchers, biochar-stakeholders, and practitioners make more well-informed choices in terms of how these three major parameters influence the final biochar product. Utilizing approximately 5400 peer-reviewed journal articles and over 50,800 individual data points, herein we elucidate the selections that influence final biochar physical and chemical properties, total nutrient content, and perhaps more importantly tools one can use to predict biochar’s nutrient availability. Based on the large dataset collected, it appears that pyrolysis type (fast or slow) plays a minor role in biochar physico- (inorganic) chemical characteristics; few differences were evident between production styles. Pyrolysis temperature, however, affects biochar’s longevity, with pyrolysis temperatures > 500 °C generally leading to longer-term (i.e., > 1000 years) half-lives. Greater pyrolysis temperatures also led to biochars containing greater overall C and specific surface area (SSA), which could promote soil physico-chemical improvements. However, based on the collected data, it appears that feedstock selection has the largest influence on biochar properties. Specific surface area is greatest in wood-based biochars, which in combination with pyrolysis temperature could likely promote greater changes in soil physical characteristics over other feedstock-based biochars. Crop- and other grass-based biochars appear to have cation exchange capacities greater than other biochars, which in combination with pyrolysis temperature could potentially lead to longer-term changes in soil nutrient retention. The collected data also suggest that one can reasonably predict the availability of various biochar nutrients (e.g., N, P, K, Ca, Mg, Fe, and Cu) based on feedstock choice and total nutrient content. Results can be used to create designer biochars to help solve environmental issues and supply a variety of plant-available nutrients for crop growth.

scholarly journals Development and Characterization of Composite Carbon Adsorbents with Photocatalytic Regeneration Ability: Application to Diclofenac Removal from Water

Catalysts ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 173
Author(s):  
Velma Beri Kimbi Yaah ◽  
Satu Ojala ◽  
Hamza Khallok ◽  
Tiina Laitinen ◽  
Marcin Selent ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
Palm Kernel ◽  
Hydrothermal Carbonization ◽  
Carbon Composite ◽  
Carbon Adsorbents ◽  
Regeneration Ability ◽  
Activation Temperature

This paper presents results related to the development of a carbon composite intended for water purification. The aim was to develop an adsorbent that could be regenerated using light leading to complete degradation of pollutants and avoiding the secondary pollution caused by regeneration. The composites were prepared by hydrothermal carbonization of palm kernel shells, TiO2, and W followed by activation at 400 °C under N2 flow. To evaluate the regeneration using light, photocatalytic experiments were carried out under UV-A, UV-B, and visible lights. The materials were thoroughly characterized, and their performance was evaluated for diclofenac removal. A maximum of 74% removal was observed with the composite containing TiO2, carbon, and W (HCP25W) under UV-B irradiation and non-adjusted pH (~5). Almost similar results were observed for the material that did not contain tungsten. The best results using visible light were achieved with HCP25W providing 24% removal of diclofenac, demonstrating the effect of W in the composite. Both the composites had significant amounts of oxygen-containing functional groups. The specific surface area of HCP25W was about 3 m2g−1, while for HCP25, it was 160 m2g−1. Increasing the specific surface area using a higher activation temperature (600 °C) adversely affected diclofenac removal due to the loss of the surface functional groups. Regeneration of the composite under UV-B light led to a complete recovery of the adsorption capacity. These results show that TiO2- and W-containing carbon composites are interesting materials for water treatment and they could be regenerated using photocatalysis.

Preparation of Sands Modified by Aluminous Salt and its Adsorption Capability of CD2+

2011 ◽  
Vol 130-134 ◽  
pp. 856-859
Author(s):  
Chun Sheng Ding ◽  
Yang Ping Fu ◽  
Qian Fen Zhu ◽  
Jing Fu
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Influencing Factors ◽  
Removal Efficiency ◽  
Specific Surface Area ◽  
Quartz Sand ◽  
Ph Value ◽  
Alkaline Condition ◽  
Initial Concentration ◽  
Adsorption Capability

In this experiment quartz sand was chosen as a carrier to be coated by aluminous salt under alkaline condition, and then the specific surface area was tested, and the adsorption capability and Cd2+ removal influencing factors of modified sand were studied. The investigation results showed that the specific surface area of modified sand was 75.244m2/g which was 9.38 times of that of original sand; the removal efficiency of Cd2+ by aluminous salt modified sand reached 59% contrast to 39% of original sand with pH 7.00. It was also found that the removal efficiency of Cd2+ by the aluminous salt modified sand was reduced with the increase of initial concentration of Cd2+ solution, and was enhanced with the increase of pH value, the Cd2+ removal efficiency was almost 71% with pH 9.0.

Comparative Analysis on Chemical Composition and Charcoal Characterization of Two Miscanthus Species

2011 ◽  
Vol 415-417 ◽  
pp. 1265-1272
Author(s):  
Wen Biao Zhang ◽  
Wen Zhu Li ◽  
Bing Song Zheng
Keyword(s):  
Chemical Composition ◽  
Specific Surface ◽  
Water Content ◽  
Surface Area ◽  
Specific Surface Area ◽  
Ph Value ◽  
Perennial Grass ◽  
Water Extract ◽  
Carbonization Temperature ◽  
Hot Water

Miscanthus is a highly productive, rhizomatous, C4 perennial grass that should be considered as an excellent active carbon precursor. This paper compares the charcoal characterization and chemical composition between M. sinensis and M. floridulus. Species differed in water content, hot water extract, 1% NaOH extract, organic solvent extract, cellulose, lignin and ash. Carbonization temperatures have effects on charcoal yields of Miscanthus, which ranged from 23.5% to 48.0% for M. sinensis and 11.3% to 37.2% for M. floridulus. Water content, charcoal density, pH value, and specific surface area of charcoal characterization varied between two species of Miscanthus. The specific surface area increased with the increase of carbonization temperature. The highest specific surface area of M. sinensis and M. floridulus was 351.74 m2g−1and 352.74 m2g−1, respectively, when the carbonization temperature was 800°C.

Preparing of Silica Aerogel and Adsorption Performance on Nitrobenzene

2012 ◽  
Vol 512-515 ◽  
pp. 1980-1985
Author(s):  
Ya Jun Luo ◽  
Xue Li ◽  
Xiao Li Hu ◽  
Deng Liang He ◽  
Peng Lin
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Ph Value ◽  
Adsorption Property ◽  
Infrared Absorption Spectrum ◽  
Nitrobenzene Solution ◽  
Silica Source ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

SiO2aerogel is prepared under normal conditions by taking tetraethyl orthosilicate (TEOS) as the silica source, N-hexane as the displacer, trimethylchlorosilane hexane as the modifier and hydrolysis environment provided by hydrochloric acid and ammonia water. The effect of pH value, time, temperature, initial concentration on the adsorption of nitrobenzene by aerogel has been studied. The results show that the best range of the pH value for adsorption is 10.72. When adsorption time is 100 min, adsorption equilibrium can be reached. The best temperature for adsorption is 40 °C. The adsorption capacity becomes larger with the concentration increasing of the nitrobenzene solution. When the concentration reaches 500 mg/L, the adsorption reaches 32.402 mg/g. The adsorption equation matches Langmuir model. Scanning Electron Microscopes (SEM), infrared absorption spectrum and specific surface area measurements have shown that the adsorption property of SiO2aerogel for the nitrobenzene is related to cellular structure of the aerogel and large specific surface area.

Examinations of Cross-Linked Polyvinylpyridine in Open Reactor

2005 ◽  
Vol 494 ◽  
pp. 369-374 ◽  
Author(s):  
M. Milošević ◽  
N. Pejić ◽  
Ž. Čupić ◽  
S. Anić ◽  
Lj. Kolar-Anić
Keyword(s):  
Specific Surface ◽  
Bifurcation Diagram ◽  
Surface Area ◽  
Specific Surface Area ◽  
Bifurcation Point ◽  
Particle Density ◽  
Physicochemical Characteristics ◽  
Stirred Tank ◽  
Stirred Tank Reactor ◽  
Tank Reactor

Macroporous cross-linked copolymer of 4-vinylpyridine and 25% (4:1) divinylbenzene is analyzed under open conditions, that is in a continuous well-stirred tank reactor (CSTR). With this aim the appropriate bifurcation diagram is found and the behavior of the system with and without polymer in the vicinity of the bifurcation point is used for the polymer examinations. Two different granulations of polymer are considered. Moreover, some physicochemical characteristics of the polymer, such as specific surface area, skeletal and particle density, are determined.

scholarly journals Obtaining of transition phases of alumina starting from sodium aluminate in Bayer process

2011 ◽  
Vol 65 (3) ◽  
pp. 271-277
Author(s):  
Zoran Obrenovic ◽  
Radislav Filipovic ◽  
Marija Milanovic ◽  
Ivan Stijepovic ◽  
Ljubica Nikolic
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Ph Value ◽  
Sodium Aluminate ◽  
High Specific Surface Area ◽  
Heterogeneous Structure ◽  
Aluminate Solution ◽  
Bayer Liquor ◽  
Sodium Aluminate Solution

Transition (active) phases of alumina were synthesized starting from sodium aluminate solution prepared out of Bayer liquor. The neutralisation of sodium aluminate solution was performed by sulphuric acid. Powder X-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and low-temperature nitrogen absorption studies were employed to trace the formation of the transition phases of alumina. The results show that the properties of the powders (phase composition, morphology and specific surface area) are strongly influenced by the initial pH value of the system, as well as by the duration of neutralisation step. It is possible to obtain powders with heterogeneous structure with dominant phase of bayerite, gibbsite or boehmit by tuning the pH and concentration of the starting sodium aluminate solution. The transition (active) phases of alumina (?- and ?-alumina) with high specific surface area (264-373 m2/g) are formed through the thermal dehydratation of aluminium hydroxide (bayerite and gibbsite) and aluminium oxyhydroxide (boehmite or pseudoboehmite) at the temperature of 500?C. Namely, bayerite and pseudoboehmite transforms to ?-phase of alumina upon heating, while gibbsite transforms to ?-phase, maintaining the parent morphology.

scholarly journals Adsorption of pharmaceuticals from aqueous solutions using biochar derived from cotton gin waste and guayule bagasse

Biochar ◽  
2020 ◽  
Author(s):  
Marlene C. Ndoun ◽  
Herschel A. Elliott ◽  
Heather E. Preisendanz ◽  
Clinton F. Williams ◽  
Allan Knopf ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
High Surface ◽  
Strong Interactions ◽  
Solution Ph ◽  
Experimental Conditions ◽  
Cotton Gin Waste ◽  
Cotton Gin

Abstract Biochars produced from cotton gin waste (CG) and guayule bagasse (GB) were characterized and explored as potential adsorbents for the removal of pharmaceuticals (sulfapyridine-SPY, docusate-DCT and erythromycin-ETM) from aqueous solution. An increase in biochar pyrolysis temperature from 350 οC to 700 οC led to an increase in pH, specific surface area, and surface hydrophobicity. The electronegative surface of all tested biochars indicated that non-Coulombic mechanisms were involved in adsorption of the anionic or uncharged pharmaceuticals under experimental conditions. The adsorption capacities of Sulfapyridine (SPY), Docusate (DCT) and Erythromycin (ETM) on biochar were influenced by the contact time and solution pH, as well as biochar specific surface area and functional groups. Adsorption of these pharmaceutical compounds was dominated by a complex interplay of three mechanisms: hydrophobic partitioning, hydrogen bonding and π–π electron donor–acceptor (EDA) interactions. Despite weaker π–π EDA interactions, reduced hydrophobicity of SPY− and increased electrostatic repulsion between anionic SPY− and the electronegative CG biochar surface at higher pH, the adsorption of SPY unexpectedly increased from 40% to 70% with an increase in pH from 7 to 10. Under alkaline conditions, adsorption was dominated by the formation of strong negative charge-assisted H-bonding between the sulfonamide moiety of SPY and surface carboxylic groups. There seemed to be no appreciable and consistent differences in the extent of DCT and ETM adsorption as the pH changed. Results suggest the CG and GB biochars could act as effective adsorbents for the removal of pharmaceuticals from reclaimed water prior to irrigation. High surface area biochars with physico-chemical properties (e.g., presence of functional groups, high cation and anion exchange capacities) conducive to strong interactions with polar-nonpolar functionality of pharmaceuticals could be used to achieve significant contaminant removal from water. Graphic Abstract

scholarly journals Effects of Wet Oxidation Process on Biochar Surface in Acid and Alkaline Soil Environments

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2362 ◽  
Author(s):  
Qinya Fan ◽  
Liqiang Cui ◽  
Guixiang Quan ◽  
Sanfei Wang ◽  
Jianxiong Sun ◽  
...  
Keyword(s):  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
Contaminated Soils ◽  
Soil Conditions ◽  
Acid Oxidation ◽  
Wet Oxidation ◽  
Alkaline Soil

Biochar has been studied for remediation of heavy metal-contaminated soils by many researchers. When in external conditions, biochar in soils ages, which can transform its structural properties and adsorption capacity. This study was conducted with two oxidation processes, HNO3/H2SO4 and NaOH/H2O2, to simulate the effects of biochar in acid and alkaline soil conditions. The results show that the oxygen-containing functional groups increased in aged biochar, which led to improve the ratio of oxygen and carbon (O/C). Nitro functional groups were found in the acid-oxidation treated biochar. Destroyed ditches and scars were observed on the surface of aged biochar and resulted in growth in their specific surface area and porosity. Specific surface area increased by 21.1%, 164.9%, and 63.0% for reed-derived biochar treated with water washing, acid oxidation, and basic oxidation, respectively. Greater peaks in the Fourier Transform Infrared Spectroscopy (FTIR) results were found in C–O and O–H on the surface of field-aged biochar. Meanwhile, mappings of energy-dispersive spectroscopy showed that biochar aged in soil was abundant in minerals such as silicon, iron, aluminum, and magnesium. In summary, biochar subjected to wet oxidation aging had an increased capacity to immobilize Cd compared to unaged biochar, and the adsorption capacity of oxidized biochar increased by 28.4% and 13.15% compared to unaged biochar due to improvements in porosity and an increase in functional groups.

scholarly journals Physicochemical and Microstructural Properties of Red Muds under Acidic and Alkaline Conditions

2020 ◽  
Vol 10 (9) ◽  
pp. 2993
Author(s):  
Qingke Nie ◽  
Youdong Li ◽  
Guohui Wang ◽  
Bing Bai
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Red Mud ◽  
Ph Value ◽  
Soil Layer ◽  
Microstructural Properties ◽  
Naoh Solution ◽  
Red Muds ◽  
Hcl Solution

The main purpose of this study was to characterize the mineral and chemical composition of typical red muds in China. Changes in the physicochemical and microstructural properties of red muds collected from the Shanxi and Shandong provinces were investigated after they were immersed in an alkaline NaOH or an acidic HCl solution for 7, 28, and 120 days. The results showed that red mud has a high cation exchange capacity and active physicochemical properties, which can be closely related to its extremely high alkalinity and complex microstructure. The neutralization of red mud with the HCl solution results in the release of Na+ from the red mud particles into the leachate and can effectively decrease the pH value of the filtrate. The neutralization process can result in a significant decrease in the liquid limit, plastic limit and plasticity index, whereas the opposite was observed for the different parameters after the addition of the NaOH solution. In this sense, acid neutralization can significantly improve the cementation property of the red mud. This result will increase the water permeability of the acid-treated soil layer and improve the growth ability of plants. The specific surface area of red mud immersed in the NaOH solution decreased, whereas the specific surface area of red mud immersed in the HCl solution increased. This study contributes to our understanding of red mud properties after the red mud has been subjected to acidic and alkaline treatments, and the results can provide insights into the safe disposal of red mud.

Sign in / Sign up

Export Citation Format

Share Document