Preparation and Properties of Carbon Fiber/Si$lt;inf$gt;3$lt;/inf$gt;N$lt;inf$gt;4$lt;/inf$gt; Composites

2014 ◽  
Vol 29 (9) ◽  
pp. 1003 ◽  
Author(s):  
WANG He-Yun ◽  
LIU Qian ◽  
ZHOU Yao ◽  
ZHOU Zhen-Zhen ◽  
LIU Guang-Hui
Keyword(s):  
Carbon Fiber

Effects of high pressure on the crystallization of carbon fiber reinforced polyetheretherketone (CF/PEEK) laminate composites

1990 ◽  
Vol 48 (4) ◽  
pp. 876-877
Author(s):  
Hong-Ming Lin ◽  
C. H. Liu ◽  
R. F. Lee
Keyword(s):  
High Pressure ◽  
Carbon Fiber ◽  
Sample Surface ◽  
High Yield ◽  
Fiber Reinforced ◽  
Laminate Composites ◽  
Peek Composite ◽  
Continuous Carbon Fiber ◽  
Carbon Fiber Reinforced

Polyetheretherketone (PEEK) is a crystallizable thermoplastic used as composite matrix materials in application which requires high yield stress, high toughness, long term high temperature service, and resistance to solvent and radiation. There have been several reports on the crystallization behavior of neat PEEK and of CF/PEEK composite. Other reports discussed the effects of crystallization on the mechanical properties of PEEK and CF/PEEK composites. However, these reports were all concerned with the crystallization or melting processes at or close to atmospheric pressure. Thus, the effects of high pressure on the crystallization of CF/PEEK will be examined in this study.The continuous carbon fiber reinforced PEEK (CF/PEEK) laminate composite with 68 wt.% of fibers was obtained from Imperial Chemical Industry (ICI). For the high pressure experiments, HIP was used to keep these samples under 1000, 1500 or 2000 atm. Then the samples were slowly cooled from 420 °C to 60 °C in the cooling rate about 1 - 2 degree per minute to induce high pressure crystallization. After the high pressure treatment, the samples were scanned in regular DSC to study the crystallinity and the melting temperature. Following the regular polishing, etching, and gold coating of the sample surface, the scanning electron microscope (SEM) was used to image the microstructure of the crystals. Also the samples about 25mmx5mmx3mm were prepared for the 3-point bending tests.

Enhanced performance of supercapacitors by constructing a “mini parallel-plate capacitor” in an electrode with high dielectric constant materials

2020 ◽  
Vol 8 (32) ◽  
pp. 16661-16668
Author(s):  
Huayao Tu ◽  
Shouzhi Wang ◽  
Hehe Jiang ◽  
Zhenyan Liang ◽  
Dong Shi ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Carbon Fiber ◽  
Parallel Plate ◽  
Sandwich Structure ◽  
High Dielectric Constant ◽  
Parallel Plate Capacitor ◽  
Plate Capacitor ◽  
Fiber Metal ◽  
High Dielectric ◽  
Mini Plate

The carbon fiber/metal oxide/metal oxynitride layer sandwich structure is constructed in the electrode to form a mini-plate capacitor. High dielectric constant metal oxides act as dielectric to increase their capacitance.

Modification of activated carbon fiber pore structure by coke deposition

2001 ◽  
Vol 11 (PR3) ◽  
pp. Pr3-279-Pr3-286
Author(s):  
X. Dabou ◽  
P. Samaras ◽  
G. P. Sakellaropoulos
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Pore Structure ◽  
Activated Carbon Fiber ◽  
Coke Deposition

New unibody clamp anchors for post-tensioning carbon-fiber-reinforced polymer rods

PCI Journal ◽  
2014 ◽  
Vol 59 (1) ◽  
pp. 103-113 ◽  
Author(s):  
Clayton A. Burningham ◽  
Chris P. Pantelides ◽  
Lawrence D. Reaveley
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced ◽  
Post Tensioning ◽  
Polymer Rods

Epoxy composites using vapor-grown carbon fiber fillers for advanced electroconductive adhesive agents

1994 ◽  
Vol 9 (4) ◽  
pp. 841-843 ◽  
Author(s):  
M. Katsumata ◽  
M. Endo ◽  
H. Ushijima ◽  
H. Yamanashi
Keyword(s):  
Carbon Fiber ◽  
Epoxy Composites
Sign in / Sign up

Export Citation Format

Share Document