Occurrence of plastic instabilities in dynamic microhardness testing

1998 ◽  
Vol 13 (6) ◽  
pp. 1411-1413 ◽  
Author(s):  
G. Bérces ◽  
N. Q. Chinh ◽  
A. Juháasz ◽  
J. Lendvai
Keyword(s):  
Room Temperature ◽  
Loading Rate ◽  
Testing Machine ◽  
Load Curve ◽  
Serrated Yielding ◽  
Microhardness Testing ◽  
Chatelier Effect ◽  
Computer Controlled ◽  
Solute Atoms ◽  
Constant Loading Rate

Plastic instabilities were observed to appear during dynamic ultramicrohardness testing of a solid solution Al–3.3 wt.% Mg alloy. The tests were carried out at room temperature with a Vickers hardness indenter in a computer-controlled dynamic ultramicrohardness testing machine. During the tests the applied load was increased from 0 to 2000 mN at constant loading rate. The instabilities appear as characteristic steps in the continuously recorded load-indentation depth curves. The physical basis for the occurrence of the instabilities is the interaction between moving dislocations and solute atoms, a phenomenon termed in the literature as serrated yielding, jerky flow, or Portevin-Le Châtelier effect. The instabilities start at a critical load, Fc, in the depth-load curve. Varying the loading rate, μ, by two orders of magnitude Fc was found to increase linearly with the loading rate.

Critical concentration of Mg addition for plastic instabilities in Al–Mg alloys

2000 ◽  
Vol 15 (5) ◽  
pp. 1037-1040 ◽  
Author(s):  
N. Q. Chinh ◽  
F. Csikor ◽  
Zs. Kovács ◽  
J. Lendvai
Keyword(s):  
Room Temperature ◽  
Loading Rate ◽  
Critical Concentration ◽  
Solute Concentration ◽  
Mg Alloys ◽  
Depth Sensing ◽  
Solute Content ◽  
Mg Addition ◽  
Constant Loading Rate ◽  
Al Mg Alloys

Plastic instabilities were investigated by the depth-sensing microhardness test in binary high-purity Al–Mg alloys with different Mg contents. During the tests the applied load was increased from 0 to 2000 mN at constant loading rate. The instabilities appeared as characteristic steps in the load–depth curves during indentation. It was shown that the occurrence and development of the plastic instabilities depend strongly on the solute content. Furthermore, the plastic instabilities occurred only when the solute concentration was larger than a critical value, C0. From room-temperature tests on Al–Mg alloys, C0 was found to be 0.86 wt% Mg. The critical concentration, which is necessary to get plastic instabilities, was also interpreted theoretically.

Dynamic and Quasi-Static Compressive Deformation Behaviour of Polyimide Foam at Various Elevated Temperature

2014 ◽  
Vol 566 ◽  
pp. 158-163 ◽  
Author(s):  
A. Yosimoto ◽  
Hidetoshi Kobayashi ◽  
Keitaro Horikawa ◽  
Keiko Watanabe ◽  
Kinya Ogawa
Keyword(s):  
Compressive Strength ◽  
Room Temperature ◽  
Deformation Behaviour ◽  
Testing Machine ◽  
Negative Temperature ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Universal Testing ◽  
Pressure Bar

In order to clarify the effect of strain rate and test temperature on the compressive strength and energy absorption of polyimide foam, a series of compression tests for the polyimide foam with two different densities were carried out. By using three testing devices, i.e. universal testing machine, dropping weight machine and sprit Hopkinson pressure bar apparatus, we performed a series of compression tests at various strain rates (10-3~103s-1) and at several test temperatures in the range of room temperature to 280 ̊C. At over 100 s-1, the remarkable increase of flow stress was observed. The negative temperature dependence of strength was also observed.

Study on the mutual interactions between the parameters of a CANON system and its coping strategy when operating at room temperature (15 to 25 °C) using response surface methodology

2014 ◽  
Vol 69 (9) ◽  
pp. 1805-1812 ◽  
Author(s):  
Jian Zhou ◽  
Guangxu Qin ◽  
Jianbing Zhang ◽  
Yancheng Li ◽  
Qiang He ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Coping Strategy ◽  
Room Temperature ◽  
Loading Rate ◽  
Nitrogen Loading ◽  
Independent Variables ◽  
Do Concentration ◽  
N Loading

The coping strategy of a CANON (completely autotrophic nitrogen removal over nitrite) reactor working at room temperature was investigated using response surface methodology. The total nitrogen (TN) removal efficiency was taken as a dependent variable. The temperature (X), dissolved oxygen (DO) concentration (Y), and influent nitrogen loading rate (Z) were taken as independent variables. Results showed that the relation of these three independent variables can be described by the TN removal efficiency expressed as −5.03 + 1.51X + 45.16Y + 30.13Z + 0.26XY + 1.84XZ − 0.04X2 − 9.06Y2 − 99.00Z2. The analysis of variance proved that the equation is applicable. The response surface demonstrated that the temperature significantly interacts with the DO concentration and influent N loading rate. A coping strategy for the CANON reactor working at room temperature is thus proposed: altering the DO concentration and the N loading rate to counterbalance the impact of low temperature. The verification test proved the strategy is viable. The TN removal efficiency was 91.3% when the reactor was operated under a temperature of 35.0 °C, a DO of 3.0 mg/L, and a N loading rate of 0.70 kgN/(m³ d). When the temperature dropped from 35.0 to 19.2 °C, the TN removal efficiency was kept at 88.7% by regulating the influent N loading rate from 0.7 kgN/(m³ d) to 0.35 kgN/(m³ d) and the DO concentration from 3.0 to 2.6 mg/L.

Dynamic Strain Aging during Tensile Deformation of Extruded AZ81 Magnesium Alloy

2013 ◽  
Vol 652-654 ◽  
pp. 1937-1941 ◽  
Author(s):  
Si Qian Zhang ◽  
Liang Mao ◽  
Li Jia Chen
Keyword(s):  
Dynamic Strain Aging ◽  
Strain Aging ◽  
Tensile Deformation ◽  
Rate Sensitivity ◽  
Dynamic Strain ◽  
Dynamic Strain Ageing ◽  
Strain Ageing ◽  
Serrated Flow ◽  
Chatelier Effect ◽  
Solute Atoms

Serrated flow has been observed in AZ81 alloy during tensile deformation. The observed static strain ageing effect and negative strain rate sensitivity suggest that the serrated flow is due to interaction between dislocations and solute atoms, know as dynamic strain ageing (DSA). The Portevin-Le Chatelier effect is observed at temperatures between 150oC~200oC and 125oC~200oC. In the microstructure of deformed samples dislocations and twins is observed. It is suggested that the occurrence of the dynamic strain aging is associated with interactions between solute atoms and dislocations.

Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8Cu-0.5Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 257-260 ◽  
Author(s):  
Zhen Yan Zhang ◽  
Li Ming Peng ◽  
Xiao Qin Zeng ◽  
Lin Du ◽  
Lan Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Solute Atoms

Effects of extrusion on mechanical properties and damping capacity of Mg-1.8wt.%Cu -0.5wt.%Mn (MCM1805) alloy have been investigated. Tensile tests and dynamic mechanical analyzer were respectively used to measure tensile properties and damping capacity at room temperature of as-cast and as-extruded MCM1805 alloy. The microstructure was studied using optical microscope, X-ray diffraction and scanning electron microscope with an energy dispersive X-ray spectrometer. Granato-Lücke model was used to explain the influences of extrusion on damping capacity of MCM1805 alloy. The results showed that extrusion dramatically decreases the grain size but has little influence on phase composition and solute atoms concentration of MCM1805 alloy, and the grain refinement was the dominant reason for the obvious increase of tensile properties and decrease of internal friction of MCM1805 alloy.

An Experimental Study of Carbon Nanotube Reinforcements

2011 ◽  
Author(s):  
Lauren Patrin ◽  
Frank Chow ◽  
Gabriela Philippart ◽  
Feridun Delale ◽  
Benjamin Liaw ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Young's Modulus ◽  
Testing Machine ◽  
Type I ◽  
Electrical Measurements ◽  
Standard Type ◽  
Reinforcement Percentage

Due to their high strength and stiffness carbon nanotubes (CNTs) have been considered as candidates for reinforcement of polymeric resins. It is also known that the addition of CNTs to polymeric matrix results in highly conductive nanocomposites, making the material multifunctional. Most of the CNT reinforced polymeric nanocomposite systems reported in the literature have been studied at room temperature. However, in many applications, materials may be subjected from low to elevated temperatures. Thus, the aim of this research is to study CNT reinforced polypropylene (PP) specimens at room, elevated and low temperatures. ASTM standard Type I specimens manufactured via injection molding and reinforced with 0.2%, 1%, 3%, and 6% CNTs were first subjected to tensile loads in a universal testing machine at room temperature. Neat PP resin specimens were also tested to provide baseline data. The tests were repeated at −54°C (−65°F), −20°C (−4°F), 49°C (120°F) and 71°C (160°F). The results were plotted as stress-strain curves and analyzed to delineate the effect of CNT reinforcement percentage and temperature on the mechanical properties. It was noted that as the percentage of CNT reinforcement increases, the resulting nanocomposite becomes stiffer (higher Young’s modulus), has higher strength and becomes more brittle. Temperature has a drastic effect on the behavior of the nanocomposite. As the temperature increases, at a given reinforcement percentage the material becomes more ductile with significantly lower Young’s modulus and strength compared to room temperature. At lower temperatures, the nanocomposite becomes more brittle with higher stiffness and strength, but significantly reduced failure strain. Also electrical measurements were conducted on the specimens to measure their resistance. For specimens reinforced with up to 3% of CNTs no electrical conductivity was detected. As expected at 6% CNT reinforcement (which is above the approximately 4% percolation limit reported in the literature), the specimens became electrically conductive. To predict the mechanical properties obtained experimentally, a micromechanics based model is presented and compared with the experimental results.

Nonlinear Rate-Dependent Stress-Strain Behavior of Light-Weight Textile Conveyor Belt

2011 ◽  
Vol 675-677 ◽  
pp. 453-456
Author(s):  
Ze Xing Wang ◽  
Jin Hua Jiang ◽  
Nan Liang Chen
Keyword(s):  
Loading Rate ◽  
Testing Machine ◽  
Rate Sensitivity ◽  
Sensitivity Coefficient ◽  
Conveyor Belt ◽  
Uniaxial Tensile ◽  
Stress Strain ◽  
Strain Behavior ◽  
Rate Dependent ◽  
Dependent Behavior

In order to investigate the effect of loading rate on the tensile performance, the uniaxial tensile experiments were conducted on universal testing machine under different loading rates (5 mm/min, 10mm/min, 50 mm/min, 100 mm/min and 150 mm/min), and a constant gage length equal to 200mm, resulting in loading strain rate of 4.17×10-4, 8.33×10-4/s, 4.17×10-3/s, 8.33×10-3/s,1.25×10-2/s, and the tensile stress-strain curves were obtained. The experimental results show that the tensile properties of the conveyor belt exhibit obvious rate-dependent behavior. In this paper, the rate sensitivity coefficient varied with loading rate, was calculated, and the nonlinear rate-dependent behavior was also investigated.

Molecular Dynamics Simulation of Nanoindentation on Folded Chain Crystal of Polyethylene

2005 ◽  
Vol 297-300 ◽  
pp. 2247-2252 ◽  
Author(s):  
Kisaragi Yashiro ◽  
Atsushi Furuta ◽  
Yoshihiro Tomita
Keyword(s):  
Molecular Dynamics ◽  
Molecular Dynamics Simulation ◽  
Loading Rate ◽  
Dynamics Simulation ◽  
Delayed Response ◽  
Berkovich Indenter ◽  
Orthorhombic Crystal ◽  
Constant Loading ◽  
Constant Loading Rate ◽  
The Ideal

Nanoindentation tests on a folded chain crystal of polyethylene are implemented with the molecular dynamics simulation. The orthorhombic crystal is made of the planar zig-zag chains and has the thickness of about 10nm. The ideal Berkovich indenter is plunged into upper surface of the crystal down to 2nm with the constant loading rate of 200m/s or 2000m/s. After the holding time of 1000fs at the maximum depth, the indenter is then pulled up with the same speed. The results are summarized as follows; a) The indentation of 2000m/s remains the residual depression while that of 200m/s recovers the hollow, b) No elastic component is found in the deformation under the both rate of 200m/s and 2000m/s, c) The crystal deforms statically under the indentation of 200m/s while that of 2000m/s shows delayed response.

Measurement of Physical and Mechanical Properties of Russian Olive (Elaeagnus Angustifolia L.) Fruit

2016 ◽  
Vol 12 (1) ◽  
pp. 91-100 ◽  
Author(s):  
Mohammad Hossein Nadian ◽  
Mohammad Hossein Abbaspour-fard
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Loading Rate ◽  
Geometric Mean ◽  
Testing Machine ◽  
Physical And Mechanical Properties ◽  
Angle Of Repose ◽  
Shear Mode ◽  
Russian Olive ◽  
Double Shear

Abstract The effect of moisture content on some properties of two varieties (Meymeh and Maragheh) of Russian olives was studied. The physical and mechanical properties including: dimensions, geometric mean diameter, thousand mass, volume, sphericity, surface area, true and bulk densities, porosity, angle of repose, coefficient of friction, rupture force, and rupture energy. The changes of moisture content levels from 17% to 25% (w.b.) indicated a statistically significant effect on all studied physical properties, except bulk density for Russian olive fruits. Shearing force was applied to the fruit using a testing machine in double shear mode. Shear strength and shearing energy increased with increase of loading rate; however, they were higher in Meymeh variety than Maragheh variety. Therefore, the lowest loading rate, with up to about 10 mm/min is desirable to design a suitable pulverizing mill in the herbal medicine industries.

Sign in / Sign up

Export Citation Format

Share Document