Synthesis of Crystalline ZnO Nanosheets on Graphene and Other Substrates at Ambient Conditions

2012 ◽  
Vol 1449 ◽  
Author(s):  
Phani Kiran Vabbina ◽  
Santanu Das ◽  
Nezih Pala ◽  
Wonbong Choi
Keyword(s):  
Synthesis Method ◽  
Zinc Nitrate ◽  
Environmentally Benign ◽  
Nitrate Hexahydrate ◽  
Ambient Conditions ◽  
X Ray ◽  
Extensive Analysis ◽  
Transmission Electron ◽  
Zno Nanosheets ◽  
Sonochemical Reaction

ABSTRACTWe report on the fabrication of ZnO nanosheets on Graphene and other substrates at ambient conditions. The growth mechanism and the effect of the substrate are also discussed. Our synthesis method is based on sonochemical reaction of Zinc nitrate hexahydrate and hexamethylenetetramine in aqueous solutions. Extensive analysis by transmission electron microscopy, energy dispersive x-ray spectroscopy (EDS) revealed crystalline ZnO composition of the ZnO nanosheets. The proposed method is a rapid, inexpensive, low-temperature, catalystfree, CMOS compatible and environmentally benign alternative to existing growth techniques.

Enhancing the photocatalytic degradation of selected chlorophenols using Ag/zno nanocomposites

MRS Advances ◽  
2018 ◽  
Vol 3 (36) ◽  
pp. 2129-2136
Author(s):  
Kate Kotlhao ◽  
Fanyana M. Mtunzi ◽  
Vusumzi Pakade ◽  
Neelan Laloo ◽  
Ikechukwu P. Ejidike ◽  
...  
Keyword(s):  
Scanning Transmission Electron Microscopy ◽  
Silver Content ◽  
Zinc Nitrate ◽  
Nitrate Hexahydrate ◽  
X Ray Diffraction ◽  
Water Contaminants ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Xrd Patterns

Chlorophenols are among the priority listed water contaminants due to their estrogenic, mutagenic or carcinogenic health effects. The Ag/ZnO nanocomposites (NCs) were synthesized, characterized and tested for photacatalytic degradation of chlorophenols in water. The synthesis was done using zinc nitrate hexahydrate (ZnNO3. 6H2O) precursor and sodium hydroxide (NaOH). Silver nitrate (AgNO3) was added to ZnO and reduced with sodium brohydride to produce the silver nanoparticles (NPs) within the ZnO structure. The silver content was varied from 1, 3 and 5wt% for optimisation. The nanocomposites were characterised using ultraviolet - visible spectroscopy (UV-Vis), photolumniscence (PL), x-ray diffraction (XRD), and scanning transmission electron microscopy (STEM). The nanocomposites were tested for their photocatalytic properties on 2- chlorophenol (CP), 2- chlorophenol (CP) and 2,4- dichlorophenol (DCP) in water. The UV-Vis results showed that, as the amount of silver was increased a gradual slight red shift was observed. The XRD patterns for Ag/ZnO exhibited peaks that were characteristic of the hexagonal wurzite structure and peaks characteristic for Ag appeared at 38.24o, 44.37o, 64.67oand 77.58ocorresponding to (111), (200), (220) and (311) reflection planes. STEM results showed the presence of Ag in ZnO with ZnO appearing as rods shapes. The EDX elemental analysis confirmed the presence of Ag in the Ag/ZnO nanocomposites with no contaminants peaks. On testing the nanocomposites for phohotocatalytic degradation of chlorophenols, addition of Ag to ZnO improved degradation of the chlorophenols compared to the pristine ZnO.

scholarly journals Biosynthesis and Characterization of ZnO: Ag2O Nanocomposite for Antifungal Efficacy

2021 ◽  
Vol 2114 (1) ◽  
pp. 012081
Author(s):  
Ali Abdullah Fayyadh ◽  
Muneer H. Jaduaa Alzubaidy
Keyword(s):  
Plant Extract ◽  
Synthesis Method ◽  
Spectroscopic Properties ◽  
Zinc Nitrate ◽  
Biological Synthesis ◽  
Nitrate Hexahydrate ◽  
Lawsonia Inermis ◽  
X Ray ◽  
Inhibitory Efficiency

Abstract In this study, biosynthesis zinc and silver oxide nanocomposite (Bs-ZANc) were prepared using an eco-friendly biological synthesis method using silver nitrate, zinc nitrate hexahydrate, and Lawsonia inermis (Henna) plant extract with four different concentrations; (0.1, 0.2, 0.3, and 0.4) molar. The detailed characterization of Bs-ZANc was performed using Grazing X-ray diffraction technique (G-XRD), Field Emission Scanning Electron Microscope (FE-SEM), X-ray energy dispersive spectroscopy (EDX), Zeta Potential (Z.P.), and Dynamic Light Scattering (DLS). In addition to studying the spectroscopic properties using Fourier transform infrared spectroscopy (FTIR). The result showed good inhibitory efficiency of Bs-ZANc against some types of fungal such as; Penicillium spp., Aspergillus spp., and Candida Albicans. Further, a comparison was made between Bs-ZANc and Lawsonia inermis (Henna) plant extract only regarding antfungal efficacy.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

Synthesis of Supergrowth VACNTs and Nanostructured ZnO by Immerse Method

2011 ◽  
Vol 312-315 ◽  
pp. 1044-1048
Author(s):  
Salina Muhamad ◽  
Abu Bakar Suriani ◽  
Mohamad Zainizan Sahdan ◽  
Anuar Ahmad ◽  
Yosri M. Siran ◽  
...  
Keyword(s):  
Crystal Orientation ◽  
Zinc Nitrate ◽  
Zinc Nitrate Hexahydrate ◽  
Nitrate Hexahydrate ◽  
X Ray Diffraction ◽  
Vertically Aligned Carbon Nanotubes ◽  
X Ray ◽  
Aligned Carbon Nanotubes ◽  
Vertically Aligned ◽  
Physical Changes

In this paper, the study of supergrowth VACNTs after being immersed in zinc oxide solution were presented. Vertically aligned carbon nanotubes (VACNTs) were first deposited on silicon with the orientation of [1 0 0] before being immersed in an aqueous solution of zinc nitrate hexahydrate and hexamethylenetetramine. Physical changes have been observed by scanning electron microscopy, SEM in the VACNTs, where the significant expansion of length of up to almost 0.8 mm was achieved after the immersion of 4.5 hr. The supergrowth of VACNTs was observed and analyzed by energy dispersive x-ray spectroscopy, EDX to substantiate the incorporation of CNTs and ZnO of the sample. Raman spectroscopy and x-ray diffraction, XRD were used to inspect the crystal orientation to support our findings.

Optimization of Green Synthesis Approach of Silver Nanoparticles Using Indonesian Wild Honey

2021 ◽  
Vol 891 ◽  
pp. 111-115
Author(s):  
Maradhana Agung Marsudi ◽  
Farah Fitria Sari ◽  
Pandu Mauliddin Wicaksono ◽  
Adinda Asmoro ◽  
Arif Basuki ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Silver Nanoparticles ◽  
Green Synthesis ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Particle Count ◽  
Transmission Electron ◽  
Nitrate Precursor ◽  
Synthesis Approach

In this work, silver nanoparticles have been successfully synthesized using simple and environmentally friendly ‘green synthesis’ method using Indonesian wild honey as mediator. Particle count and size can be optimized by varying the silver nitrate precursor and honey concentration, with the help of sodium hydroxide as pH regulator. Based on X-ray diffraction (XRD) result, crystalline structure of Ag has been confirmed in sample with impurities from AgCl. Based on dynamic light scattering (DLS) and transmission electron microscopy (TEM) results, it was found that the smallest average particles size of AgNPs (117.5 nm from DLS and 11.1 nm from TEM) was obtained at sample with 5% w/v of honey and 0.5 mM of AgNO3.

scholarly journals In Situ Growth of ZnO Nanostructures on Cotton Fabric by Solochemical Process for Antibacterial Purposes

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
D. A. R. Souza ◽  
M. Gusatti ◽  
R. Z. Ternus ◽  
M. A. Fiori ◽  
H. G. Riella
Keyword(s):  
Electron Microscopy ◽  
Cotton Fabric ◽  
Zinc Nitrate ◽  
Nitrate Hexahydrate ◽  
Zno Nanostructures ◽  
In Situ Growth ◽  
Zinc Oxide Nanostructures ◽  
Gram Positive Bacteria ◽  
Transmission Electron

A practical and economical method was developed for the production of an antibacterial cotton fabric using zinc oxide nanostructures without the use of surface modifying agents. In this process, zinc nitrate hexahydrate and potassium hydroxide were used as starting materials and the reaction was performed at 50°C. The in situ growth of ZnO nanostructures on cotton fabric occurred in a single-stage process, and it started when the fabric samples were dipped for 1 min in the solution containing all the starting materials. The treated and untreated fabric samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and EDS. The cotton fabrics coated with ZnO nanostructures presented an antibacterial efficiency towards Pseudomonas aeruginosa, a gram-negative bacteria, and Staphylococcus aureus (S. aureus), a gram-positive bacteria.

Low-Temperature Synthesis of Nano-Crystalline ZnTiO3 Powders by Aqueous Sol-Gel Process

2014 ◽  
Vol 543-547 ◽  
pp. 3741-3744
Author(s):  
Quan Jing Mei ◽  
Cong Ying Li ◽  
Jing Dong Guo ◽  
Gui Wang ◽  
Hai Tao Wu
Keyword(s):  
Sol Gel ◽  
Zinc Nitrate ◽  
X Ray Diffraction ◽  
Low Temperature Synthesis ◽  
Temperature Synthesis ◽  
Calcination Process ◽  
X Ray ◽  
Nano Crystalline ◽  
Transmission Electron ◽  
Sol Gel Process

The ecandrewsite-type ZnTiO3was successfully synthesized by the aqueous sol-gel method using TiO2dioxide and zinc nitrate as starting materials instead of expensive organic solvent and metal alkoxides. The as-prepared nanopowders were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA) and transmission electron microscopy (TEM), respectively. The results showed that the calcination process of gel consisted of a series of oxidation and combustion reactions, accompanied by significantly exothermal effects. Highly reactive nanosized ZnTiO3powders were successfully obtained at 850 °C with particle size ~50 nm. By comparison, the aqueous sol-gel process was the most effective and least expensive technique used for the preparation of ZnTiO3nanopowders.

scholarly journals Investigation of structural and optical properties of biosynthesized Zincite (ZnO) nanoparticles (NPs) via an aqueous extract of Rosmarinus officinalis (rosemary) leaves

MRS Advances ◽  
2020 ◽  
Vol 5 (45) ◽  
pp. 2349-2358 ◽  
Author(s):  
S. K. Noukelag ◽  
H.E.A. Mohamed ◽  
B. Moussa ◽  
L.C. Razanamahandry ◽  
S.K.O. Ntwampe ◽  
...  
Keyword(s):  
Aqueous Extract ◽  
Surface Defects ◽  
High Surface ◽  
Average Particle Size ◽  
Zinc Nitrate ◽  
Attenuated Total Reflection ◽  
Average Particle ◽  
Nitrate Hexahydrate ◽  
Zno Nps ◽  
X Ray

AbstractBiosynthesized Zincite nanoparticles have been successfully demonstrated by a completely green process mediated aqueous extract of rosemary leaves acting as both reducing and stabilizing agents and zinc nitrate hexahydrate as the precursor. The synthesis was free of solvents and surfactants to adhere to green chemistry principles and the impartation of environmental benignity. To achieve our objective, structural and optical investigations of ZnO annealed at 500°C for 2hrs were carried-out using complementary techniques. High resolution transmission electron microscopy (HRTEM) revealed the self-assembled, highly agglomerated quasi-hexagonal shaped NPs and the average particle size was found to peak at 15.62 ± 0.22 nm. Selected area electron diffraction (SAED) and X-ray diffraction (XRD) exhibited several diffraction rings with clear diffraction spots confirming their polycrystallinity and the purity of ZnO NPs with a wurtzite structure. Furthermore, the energy dispersive X-ray spectroscopy (EDS) substantiated the presence of Zn and O in the sample and attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) illustrated the Zn-O chemical bonds. From UV-Vis-NIR, the optical band gap was amounted to 3.2 eV and photoluminescence (PL) emission spectrum to 2.9eV with high surface defects and oxygen vacancies. Through these results, the use of rosemary leaves extract is hereby shown to be a cost-effective and environmentally friendly alternative to synthesize Zincite nanoparticles (ZnO NPs).

Two-different ways of synthesis for EG: Study of mechanical, thermal, and electrical properties of epoxy composite for TIMs

2020 ◽  
pp. 095400832094538
Author(s):  
Sagar Kumar Nayak ◽  
Arjyama Mishra ◽  
Subhransu S Pradhan ◽  
Jyoti Agarwal
Keyword(s):  
Electron Microscopy ◽  
Epoxy Composite ◽  
Expanded Graphite ◽  
Ammonium Persulfate ◽  
Zinc Nitrate ◽  
Electrochemical Process ◽  
Graphite Flake ◽  
Nitrate Hexahydrate ◽  
Transmission Electron ◽  
Inverse Rule

The current study reports the synthesis of expanded graphite (EG) in two different ways and its fabrication with epoxy matrix to form composite at various filler fractions (5, 10, 12.5). One type EG (EG-C) is prepared by the electrochemical process using natural graphite flake (NGF), concentrated sulfuric acid, and ammonium persulfate, while the other (EG-P) is just mixing and heating of NGF with zinc nitrate hexahydrate. The functional groups of synthesized EG were confirmed by Fourier transform infrared spectroscopy. The surface morphology and microstructure of synthesized filler (EG-C, EG-P) were studied using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. An optimum through-plane thermal conductivity (TC) of 2.04 and 2.22 W/mK was observed in the case of the composites containing 12.5 wt% of EG-C and EG-P, respectively. The obtained experimental TC was compared with three numerical thermal models, that is, inverse rule of mixture, Maxwell–Eucken model, and Agari model. Furthermore, the thermal stability of both composites was compared by using a thermogravimetric analyzer. The electrical resistivity of EG-P/epoxy composite at different formulations was higher than the EG-C-filled epoxy composites.

Sign in / Sign up

Export Citation Format

Share Document