Cu2SnS3 Inorganic-Organic Hybrid Structures for Photovoltaic Applications

2015 ◽  
Vol 1784 ◽  
Author(s):  
Sandra Dias ◽  
S. B. Krupanidhi
Keyword(s):  
Electron Microscopy ◽  
Hybrid Structures ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hybrid Device ◽  
Organic Hybrid ◽  
A Value ◽  
Transmission Electron ◽  
Absorption Studies ◽  
Photovoltaic Applications

ABSTRACTWe report the synthesis of Cu2SnS3 (CTS) nanostructures and its incorporation into an inorganic-organic hybrid device to enhance the photoresponse under AM 1.5 G solar illumination. The nanostructures were structurally and optically characterized. From X-ray diffraction (XRD) and Transmission electron microscopy (TEM) the CTS nanocrystals were found to be tetragonal. Flower like structures of CTS were obtained as seen from Scanning electron microscopy (SEM). A band gap of 1.4 eV was obtained from absorption studies. Two devices have been studied, P3HT: PCBM = 1: 1 and CTS: P3HT: PCBM = 8:1:1. The photocurrent increased from a value of 2.33 mA at dark to 2.5 mA for the P3HT-PCBM blend to 3.36 mA for CTS: P3HT: PCBM = 8:1:1 device. The responsivity, sensitivity, external quantum efficiency and specific detectivity increased from 18.81 mA/W, 1.07, 4.25% and 6.88 × 108 Jones respectively for P3HT:PCBM sample to 189.97 mA/W, 1.44, 42.9% and 6.95 × 109 Jones for CTS: P3HT: PCBM = 8:1:1 sample at 1V bias and 1 Sun illumination intensity. The time dependent photoresponse was stable over different ON-OFF cycles. From the fit to the rise and decay curves, the rise and decay time constants were obtained.

scholarly journals Synthesis and Characterization of Cu2FeSnSe4 Nanofilms

2021 ◽  
pp. 1873-1878
Author(s):  
Omar Abdulsada Ali ◽  
Sarmed S.M. Al-Awadi
Keyword(s):  
Electron Microscopy ◽  
Average Particle Size ◽  
Average Particle ◽  
Electrochemical Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Photovoltaic Applications ◽  
Tem Transmission Electron Microscopy

Well dispersed Cu2FeSnSe4 (CFTSe) nanofilms were synthesized by hot-injection method. The structural and morphological measurements were characterized using XRD (X-ray diffraction), Raman spectroscopy, SEM (scanning electron microscopy), and TEM (transmission electron microscopy). Chemical composition and optical properties of as-synthesized CFTSe nanoparticles were characterized using EDS (energy dispersive spectroscopy) and UV-Vis spectrophotometry. The average particle size of the nanoparticles was about 7-10 nm. The UV-Vis absorption spectra showed that the synthesized CFTS nanofilms have a band gap (Eg) of about 1.16 eV. Photo-electrochemical characteristics of CFTSe nanoparticles were studied and indicated their potential application in photovoltaic applications.

The Preparation of Bi-Pb-Sr-Ca-Cu-O Superconducting Powder for Thick Film Pastes

1989 ◽  
Vol 169 ◽  
Author(s):  
J. Hagberg ◽  
A. Uusimäki ◽  
J. Levoska ◽  
S Leppävuori ◽  
R Rautioaho
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Surface Area ◽  
Nominal Composition ◽  
X Ray Diffraction ◽  
X Ray ◽  
A Value ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Oxalate Route

AbstractThe oxalate route was used to prepare (Bi-Pb) -Sr-Ca-Cu-O powder with the nominal composition Bi1.75Pb0.4Sr1.3Ca2.1Cu3.2Oy. This powder was decomposed/annealed at different temperatures between 434 and 795°C. They were investigated by thermogravimetric analysis, X-ray diffraction and transmission electron microscopy. Particle size distribution and surface area were also determined. The specific surface area decreased from a value of 16.5 m2/g for powder decomposed at 434 °C to 1.0 m2/g for powder decomposed at 795 °C. The measured mean particle size reached a minimum of 0.52 juri for powder decomposed at 589 °C.

A High Resolution Study of G.P. Zones in Aluminum - 4.2 at % Silver

1982 ◽  
Vol 40 ◽  
pp. 722-723 ◽  
Author(s):  
R. Gronsky
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Computer Simulations ◽  
Structural Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Resolution Study

The phenomenon of clustering in Al-Ag alloys has been extensively studied since the early work of Guinierl, wherein the pre-precipitation state was characterized as an assembly of spherical, ordered, silver-rich G.P. zones. Subsequent x-ray and TEM investigations yielded results in general agreement with this model. However, serious discrepancies were later revealed by the detailed x-ray diffraction - based computer simulations of Gragg and Cohen, i.e., the silver-rich clusters were instead octahedral in shape and fully disordered, atleast below 170°C. The object of the present investigation is to examine directly the structural characteristics of G.P. zones in Al-Ag by high resolution transmission electron microscopy.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

Palladium Nanowire Thin Films via Template Growth

2003 ◽  
Vol 775 ◽  
Author(s):  
Donghai Wang ◽  
David T. Johnson ◽  
Byron F. McCaughey ◽  
J. Eric Hampsey ◽  
Jibao He ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Conductive Substrate ◽  
Palladium Nanowires ◽  
Efficient Route ◽  
Silica Thin Film

AbstractPalladium nanowires have been electrodeposited into mesoporous silica thin film templates. Palladium continually grows and fills silica mesopores starting from a bottom conductive substrate, providing a ready and efficient route to fabricate a macroscopic palladium nanowire thin films for potentially use in fuel cells, electrodes, sensors, and other applications. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicate it is possible to create different nanowire morphology such as bundles and swirling mesostructure based on the template pore structure.

scholarly journals Quartz Crystallite Size and Moganite Content as Indicators of the Mineralogical Maturity of the Carboniferous Chert: The Case of Cherts from Eastern Asturias (Spain)

Minerals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 611
Author(s):  
Celia Marcos ◽  
María de Uribe-Zorita ◽  
Pedro Álvarez-Lloret ◽  
Alaa Adawy ◽  
Patricia Fernández ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Crystallite Size ◽  
Archaeological Sites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Infrared And Raman Spectroscopy ◽  
First Time ◽  
Geological Formations

Chert samples from different coastal and inland outcrops in the Eastern Asturias (Spain) were mineralogically investigated for the first time for archaeological purposes. X-ray diffraction, X-ray fluorescence, transmission electron microscopy, infrared and Raman spectroscopy and total organic carbon techniques were used. The low content of moganite, since its detection by X-ray diffraction is practically imperceptible, and the crystallite size (over 1000 Å) of the quartz in these cherts would be indicative of its maturity and could potentially be used for dating chert-tools recovered from archaeological sites. Also, this information can constitute essential data to differentiate the cherts and compare them with those used in archaeological tools. However, neither composition nor crystallite size would allow distinguishing between coastal and inland chert outcrops belonging to the same geological formations.

Effect of synthesis and activation methods on the character of CoMo/ultrastable Y-zeolite catalysts

2021 ◽  
Vol 19 (1) ◽  
pp. 745-754
Author(s):  
Khoirina Dwi Nugrahaningtyas ◽  
Eddy Heraldy ◽  
Rachmadani ◽  
Yuniawan Hidayat ◽  
Indriana Kartini
Keyword(s):  
Electron Microscopy ◽  
Reduction Process ◽  
Particle Morphology ◽  
Zeolite Catalysts ◽  
X Ray Diffraction ◽  
Y Zeolite ◽  
X Ray ◽  
Irregular Particle ◽  
Transmission Electron ◽  
Pure Metals

Abstract The properties of three types of CoMo/USY catalysts with different synthesized methods have been studied. The sequential and co-impregnation methods followed by activation using calcination and reduction process have been conducted. The properties of the catalysts were examined using Fourier-transform-infrared (FTIR) spectroscopy, X-ray diffraction (XRD) with refinement, and surface area analyzer (SAA). The FTIR spectrum study revealed the enhanced intensity of its Bronsted acid site, and the XRD diffractogram pattern verified the composition of pure metals, oxides, and alloys in the catalyst. The SAA demonstrated the mesoporous features of the catalyst. Scanning electron microscopy showed an irregular particle morphology. Additional analysis using the transmission electron microscopy indicated that the metal has successfully impregnated without damaging the USY structure.

scholarly journals Controlled Synthesis of CuS and Cu9S5 and Their Application in the Photocatalytic Mineralization of Tetracycline

Catalysts ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 899
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Blue Shift ◽  
X Ray Diffraction ◽  
X Ray ◽  
Copper Sulfides ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Pure Phase ◽  
Pure Phases

Pure-phase Cu2−xS (x = 1, 0.2) nanoparticles have been synthesized by the thermal decomposition of copper(II) dithiocarbamate as a single-source precursor in oleylamine as a capping agent. The compositions of the Cu2−xS nanocrystals varied from CuS (covellite) through the mixture of phases (CuS and Cu7.2S4) to Cu9S5 (digenite) by simply varying the temperature of synthesis. The crystallinity and morphology of the copper sulfides were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), which showed pure phases at low (120 °C) and high (220 °C) temperatures and a mixture of phases at intermediate temperatures (150 and 180 °C). Covellite was of a spherical morphology, while digenite was rod shaped. The optical properties of these nanocrystals were characterized by UV−vis–NIR and photoluminescence spectroscopies. Both samples had very similar absorption spectra but distinguishable fluorescence properties and exhibited a blue shift in their band gap energies compared to bulk Cu2−xS. The pure phases were used as catalysts for the photocatalytic degradation of tetracycline (TC) under visible-light irradiation. The results demonstrated that the photocatalytic activity of the digenite phase exhibited higher catalytic degradation of 98.5% compared to the covellite phase, which showed 88% degradation within the 120 min reaction time using 80 mg of the catalysts. The higher degradation efficiency achieved with the digenite phase was attributed to its higher absorption of the visible light compared to covellite.

Multi-scale Investigation of Heterogeneous Swift Heavy Ion Tracks in Stannate Pyrochlore

2021 ◽  
Author(s):  
Eric O'Quinn ◽  
Cameron Tracy ◽  
William F. Cureton ◽  
Ritesh Sachan ◽  
Joerg C. Neuefeind ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Heavy Ion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structural Modifications ◽  
Multi Scale ◽  
Ion Tracks ◽  
Swift Heavy Ion ◽  
Transmission Electron

Er2Sn2O7 pyrochlore was irradiated with swift heavy Au ions (2.2 GeV), and the induced structural modifications were systematically examined using complementary characterization techniques including transmission electron microscopy (TEM), X-ray diffraction...

Sign in / Sign up

Export Citation Format

Share Document