Laminate Orientation and Thickness Effects on An Scs-6/Ti-24ai-11 Nb Composite Under Thermal Fatigue

1992 ◽  
Vol 273 ◽  
Author(s):  
William C. Revelos ◽  
Itzhak Roman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Acoustic Emission ◽  
Thermal Fatigue ◽  
Room Temperature ◽  
Maximum Temperature ◽  
Composite Strength ◽  
Inert Environment ◽  
Tension Tests ◽  
Scanning Electron

ABSTRACTA SiC/Ti-24AI-11 Nb (at. %) composite (30–35 vol. %) was thermally cycled in air and an inert environment between 150 °C and 815 °C for various cycle counts. Various hold times at maximum temperature were employed to determine timedependent effects on composite integrity. Laminate orientations investigated included: [0]4, [0]8, [90]4, [90]8 and [0/90]2S. Acoustic emission produced during thermal fatigue of selected specimens was employed to monitor damage progression. Post-cycling room temperature tension tests as well as optical and scanning electron microscopy were used to document damage, which was particularly acute when hold times at temperature were employed on tests performed in air. The roles of the environment, composite thickness, and off-axis fibers during thermal fatigue on the composite strength and integrity are discussed.

Scanning Electron Microscopy-cuticular Lesions on the Roundworm Ascaris Suum

1970 ◽  
Vol 28 ◽  
pp. 114-115
Author(s):  
P. A. Madden ◽  
W. R. Anderson
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Freeze Drying ◽  
Room Temperature ◽  
Secondary Electron ◽  
Distilled Water ◽  
Freeze Dried ◽  
Silver Paint ◽  
To Come ◽  
Scanning Electron

The intestinal roundworm of swine is pinkish in color and about the diameter of a lead pencil. Adult worms, taken from parasitized swine, frequently were observed with macroscopic lesions on their cuticule. Those possessing such lesions were rinsed in distilled water, and cylindrical segments of the affected areas were removed. Some of the segments were fixed in buffered formalin before freeze-drying; others were freeze-dried immediately. Initially, specimens were quenched in liquid freon followed by immersion in liquid nitrogen. They were then placed in ampuoles in a freezer at −45C and sublimated by vacuum until dry. After the specimens appeared dry, the freezer was allowed to come to room temperature slowly while the vacuum was maintained. The dried specimens were attached to metal pegs with conductive silver paint and placed in a vacuum evaporator on a rotating tilting stage. They were then coated by evaporating an alloy of 20% palladium and 80% gold to a thickness of approximately 300 A°. The specimens were examined by secondary electron emmission in a scanning electron microscope.

SEM Observations on the Germination of Euonymous Americanus

1985 ◽  
Vol 43 ◽  
pp. 508-509
Author(s):  
D.R. Hill ◽  
J.R. McCurry ◽  
L.P. Elliott ◽  
G. Howard
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Light Microscopy ◽  
Filter Paper ◽  
Room Temperature ◽  
Food Source ◽  
Environmental Chamber ◽  
Dormant Stage ◽  
Scanning Electron

Germination of Euonymous americanus in the laboratory has previously been unsuccessful. Ability to germinate Euonymous americanus. commonly known as the american strawberry bush, is important in that it represents a valuable food source for the white-tailed deer. Utilizing the knowledge that its seeds spend a period of time in the rumin fluid of deer during their dormant stage, we were successful in initiating germination. After a three month drying period, the seeds were placed in 25 ml of buffered rumin fluid, pH 8 at 40°C for 48 hrs anaerobically. They were then allowed to dry at room temperature for 24 hrs, placed on moistened filter paper and enclosed within an environmental chamber. Approximately four weeks later germination was detected and verified by scanning electron microscopy; light microscopy provided inadequate resolution. An important point to note in this procedure is that scarification, which was thought to be vital for germination, proved to be unnecessary for successful germination to occur. It is believed that germination was propagated by the secretion of enzymes or prescence of acids produced by microorganisms found in the rumin fluid since sterilized rumin failed to bring about germination.

Identification of Nd163 phase in melt-textured NdBa2Cu3O7−δ bulk samples

2003 ◽  
Vol 18 (9) ◽  
pp. 2050-2054 ◽  
Author(s):  
Marcello Gombos ◽  
Vicente Gomis ◽  
Anna Esther Carrillo ◽  
Antonio Vecchione ◽  
Sandro Pace ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Room Temperature ◽  
Polarized Light ◽  
Energy Dispersive ◽  
X Ray ◽  
Spontaneous Formation ◽  
The Stability ◽  
Scanning Electron

In this work, we report on the observation of Nd1Ba6Cu3O10,5 (Nd163) phase of the NdBaCuO system in melt-textured Nd123 bulk samples grown from a mixture of Nd123 and Nd210 phase powders. The observation was performed with polarized light optical microscopy and scanning electron microscopy–energy dispersive x-ray analyses. Images of the identified phase crystals show an aspect quite different from Nd422 crystals. Unexpectedly, Nd163 was individuated, even in “pure” Nd123 samples. Moreover, after long exposure to air, Nd163 disappeared completely in samples synthesized from powders containing Nd210. Thermogravimetry analyses of powders show that the stability of this phase in air is limited to temperatures higher than 900 °C, so Nd163 is unstable and highly reactive at room temperature. Moreover, an explanation of the observation of Nd163 in Nd210 free samples, based on the spontaneous formation of Nd163 phase in a Nd123 melt, is proposed.

N-type Ba0.2Co4Sb11.5Te0.5: Optimization of thermoelectric properties by different pressures

2019 ◽  
Vol 33 (03) ◽  
pp. 1950027 ◽  
Author(s):  
Jiaxiang Chen ◽  
Xiaopeng Jia ◽  
Yuewen Zhang ◽  
Haiqiang Liu ◽  
Baomin Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Absolute Value ◽  
X Ray ◽  
Coefficient Increase ◽  
Maximum Power Factor ◽  
Scanning Electron

The polycrystalline skutterudite [Formula: see text] were successfully synthesized from 1.5 GPa to 3.5 GPa by the high pressure and high temperature (HPHT) method. Negative Seebeck coefficient confirmed the n-type conductivity of all samples. The phase compositions of samples were investigated by X-ray diffraction (XRD) and the microstructures were observed by scanning electron microscopy (SEM). It was found that the grains appeared smaller and the grain boundaries became more abundant when pressures were higher. We measured the electrical properties from room temperature to 723 K. Both the electrical resistivity and absolute value of Seebeck coefficient increase with the increasing synthetic pressure. At 723 K, the maximum power factor of [Formula: see text] was obtained for the sample synthesized under 3 GPa. The maximum ZT value of 0.61 was reached by [Formula: see text] synthesized under 3 GPa and measured at 723 K.

Synthesis and Characterization of Gold Nanoparticles Synthesized in Gel and Paper by Electrolysis

2019 ◽  
Vol 824 ◽  
pp. 163-167
Author(s):  
Pema Dechen ◽  
Ekasith Somsook
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Gold Nanoparticles ◽  
Room Temperature ◽  
Synthesis And Characterization ◽  
Visible Spectroscopy ◽  
Gold Leaf ◽  
Uv Visible ◽  
Scanning Electron

In this report, synthesis and characterization of gold nanoparticles (AuNPs) from gold leaf by electrolysis in two different media (gel and paper) in presence of sodium chloride (NaCl), glucose (C6H12O6) and polyvinyl pyrrolidone (PVP) at room temperature were investigated. Graphite was used as two electrodes, NaCl was used as an electrolyte, C6H12O6 was used as reducing agent and PVP was used as stabilizer to control the aggregation of the nanoparticles. UV-Visible spectroscopy (UV-Vis) and scanning electron microscopy (SEM) were used to confirm the characteristics and morphologies of the synthesized AuNPs.

scholarly journals Properties of Luffa Fiber Reinforced PHBV Biodegradable Composites

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1765 ◽  
Author(s):  
Yong Guo ◽  
Li Wang ◽  
Yuxia Chen ◽  
Panpan Luo ◽  
Tong Chen
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Flexural Strength ◽  
Room Temperature ◽  
Moisture Resistance ◽  
Hot Press ◽  
Biodegradable Composites ◽  
Hot Press Forming ◽  
Pre Treatment ◽  
Scanning Electron

In this study, composites of poly (hydroxybutyrate-co-valerate) (PHBV) with untreated luffa fibers (ULF) and NaOH-H2O2 treated luffa fibers (TLF) were prepared by hot press forming. The properties of luffa fibers (LFs) and composites were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and other analysis methods. Results showed that pre-treatment effectively removed pectin, hemicellulose, and lignin, thus reducing the moisture absorptivity of LFs. The flexural strength of TLF/PHBV was higher than that of ULF/PHBV. With 60% LF content, the flexural strengths of ULF/PHBV and TLF/PHBV reached 75.23 MPa and 90.73 MPa, respectively, 219.7% and 285.6% more than that of pure PHBV. Water absorptivities of composites increased with increase in LF content. Water absorptivity of TLF/PHBV was lower than that of ULF/PHBV. The flexural strengths of composites decreased after immersion in water at room temperature. Meanwhile, flexural strength of TLF/PHBV was lower than that of ULF/PHBV. Pretreatment of LFs effectively improved the bonding between fibers and PHBV, resulting in enhanced and thus improved the moisture resistance of composites.

Novel Methods for Preparation and Surface Treatment of Nano-CaCO3

2013 ◽  
Vol 750-752 ◽  
pp. 336-339
Author(s):  
Fa Chao Wu ◽  
Teng Fei Shen
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Fourier Transform ◽  
Room Temperature ◽  
Transmission Electron ◽  
Reduce Energy Consumption ◽  
Scanning Electron

In this work, CaCO3 nanoparticles have been synthesized via heat-treatment of a new precursor. Effect of calcinations temperature on particle size has been investigated. The products were characterized by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). nanoCaCO3 was modified using chloroform as solvent and fatty acid as modifier atroom temperature. The advantage of this modification is that it can be proceed at room temperature and it can reduce energy consumption.

Study of Deformation Phenomena in TRIP/TWIP Steels by Acoustic Emission and Scanning Electron Microscopy

2018 ◽  
Vol 119 (4) ◽  
pp. 388-395 ◽  
Author(s):  
M. L. Linderov ◽  
C. Segel ◽  
A. Weidner ◽  
H. Biermann ◽  
A. Yu. Vinogradov
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Acoustic Emission ◽  
Twip Steels ◽  
Scanning Electron

scholarly journals Preparation and Phase Relations in the CuSbSe2 – CuInSe2 System

2016 ◽  
Vol 1735 ◽  
Author(s):  
Barys V. Korzun ◽  
Valery R. Sobol ◽  
Marin Rusu ◽  
Ruben M. Savizky ◽  
Alena A. Fadzeyeva ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Mole Fraction ◽  
Powder Diffraction ◽  
Room Temperature ◽  
Phase Relations ◽  
X Ray ◽  
Ternary Compounds ◽  
Scanning Electron

ABSTRACTThe CuInSe2 and CuSbSe2 ternary compounds and alloys of the (CuSbSe2)1-x·(CuInSe2)x system with the mole fraction of CuInSe2 (x) equal to 0.05, 0.15, 0.25, 0.375, 0.50, 0.625, 0.75, 0.85, and 0.95 were prepared and the phase relations in this system were investigated by X-ray powder diffraction, optical microscopy, and scanning electron microscopy. It was shown that the alloys of the CuSbSe2-CuInSe2 system are biphasic at room temperature in the whole range of compositions, and the limits of solubility for CuSbSe2 in CuInSe2 and for CuInSe2 in CuSbSe2 do not exceed 0.001 mole fraction.

Sign in / Sign up

Export Citation Format

Share Document