Quantitative In Situ Growth Measurements of Chlorine-Activated Homoepitaxial Diamond Cvd

1994 ◽  
Vol 349 ◽  
Author(s):  
Chenyu Pan ◽  
John L. Margrave ◽  
Robert H. Hauge
Keyword(s):  
Growth Rate ◽  
Substrate Temperature ◽  
Growth Rates ◽  
Diamond Growth ◽  
Flow Rates ◽  
Temperature Range ◽  
Quantitative Studies ◽  
Growth Activation ◽  
Lower Temperature

ABSTRACTIn situ quantitative studies of the effects of substrate temperature, methane and chlorine flow rates on homoepitaxial diamond growth rates on (110) surfaces in a chlorine-activated diamond CVD reactor have been carried out using a Fizeau interferometer. The temperature dependence of diamond growth rates was found to display three distinct growth activation energies, ranging from 9±2 kcal/mol in the substrate temperature of 750-950°C, to 3.2±0.2 kcal/mol in the temperature range of 300-650°C, followed by 1.2±0.2 kcal/mol in the temperature range of 102-250°C. Atomic hydrogen is believed to be the dominant activating species in the highest temperature range, and atomic chlorine is believed to be the dominant species in the lower temperature regions. Studies of the methane flow effect on diamond growth rates revealed a linearity, indicating that the diamond growth rate was of the first order in methane flows. Diamond growth rates were also found to increase linearly with the chlorine flow. At high chlorine flow rates, however, an accelerated diamond growth rate was observed. Discussion is given to explain the observed results.

Single Crystal Silicon Carbide On Silicon Using A Supersonic Gas Jet Of Methylsilane

1997 ◽  
Vol 483 ◽  
Author(s):  
S. A. Ustin ◽  
C. Long ◽  
L. Lauhon ◽  
W. Ho
Keyword(s):  
Growth Rate ◽  
Growth Rates ◽  
Single Crystal Silicon ◽  
Maximum Growth ◽  
X Ray Diffraction ◽  
Crystal Silicon ◽  
Cross Sectional ◽  
Supersonic Molecular Beam ◽  
Transmission Electron

AbstractCubic SiC films have been grown on Si(001) and Si(111) substrates at temperatures between 600 °C and 900 °C with a single supersonic molecular beam source. Methylsilane (H3SiCH3) was used as the sole precursor with hydrogen and nitrogen as seeding gases. Optical reflectance was used to monitor in situ growth rate and macroscopic roughness. The growth rate of SiC was found to depend strongly on substrate orientation, methylsilane kinetic energy, and growth temperature. Growth rates were 1.5 to 2 times greater on Si(111) than on Si(001). The maximum growth rates achieved were 0.63 μm/hr on Si(111) and 0.375μm/hr on Si(001). Transmission electron diffraction (TED) and x-ray diffraction (XRD) were used for structural characterization. In-plane azimuthal (ø-) scans show that films on Si(001) have the correct 4-fold symmetry and that films on Si(111) have a 6-fold symmetry. The 6-fold symmetry indicates that stacking has occurred in two different sequences and double positioning boundaries have been formed. The minimum rocking curve width for SiC on Si(001) and Si(111) is 1.2°. Fourier Transform Infrared (FTIR) absorption was performed to discern the chemical bonding. Cross Sectional Transmission Electron Microscopy (XTEM) was used to image the SiC/Si interface.

The English–Wabigoon River System: V. Mercury and Selenium Bioaccumulation as a Function of Aquatic Primary Productivity

1983 ◽  
Vol 40 (12) ◽  
pp. 2251-2259 ◽  
Author(s):  
John W. M. Rudd ◽  
Michael A. Turner
Keyword(s):  
Growth Rate ◽  
Primary Productivity ◽  
Growth Rates ◽  
River System ◽  
Whole Body ◽  
Aquatic Food Chain ◽  
Mercury Bioaccumulation ◽  
Aquatic Food ◽  
Stimulation Of

An experiment was carried out in four 100-m3 in situ enclosures to determine the effect of primary production rate on mercury and selenium concentrations of biota and to test the possibility of ameliorating mercury pollution problems by increasing ecosystem primary productivity. Two enclosures were controls. Primary productivity in a third enclosure was increased fourfold by addition of NaNO3 and NaH2PO4. This stimulation was not sufficient to change pH although the growth rate of fish was enhanced. In this enclosure, mercury concentrations in pearl dace (Semotilus margarita) whole body and muscle samples increased two- and five-fold, respectively, exceeding the dilution of mercury by the enhanced growth rates. In the fourth enclosure, at the highest rate of nutrient addition, primary productivity was increased ninefold, pH was elevated from about 7.9 to 9.2, and the growth rate of fish was stimulated. In this case, the elevation of pH retarded the rate of mercury bioaccumulation in comparison with the enclosure of intermediate productivity. Based on these results, stimulation of primary productivity is not recommended as a mercury ameliorating procedure. Stimulation of primary productivity resulted in a general decrease in the concentration of selenium in the aquatic food chain probably resulting from dilution of selenium by enhanced growth rates of fish and other biota.

scholarly journals Determination of In Situ Bacterial Growth Rates in Aquifers and Aquifer Sediments

2003 ◽  
Vol 69 (7) ◽  
pp. 3798-3808 ◽  
Author(s):  
Brian J. Mailloux ◽  
Mark E. Fuller
Keyword(s):  
Growth Rate ◽  
Fluorescence Intensity ◽  
Growth Rates ◽  
Direct Determination ◽  
Shallow Aquifer ◽  
Cell Counting ◽  
Field Scale ◽  
Doubling Times

ABSTRACT Laboratory and field-scale studies with stained cells were performed to monitor cell growth in groundwater systems. During cell division, the fluorescence intensity of the protein stain 5-(and 6-)-carboxyfluorescein diacetate succinimidyl ester (CFDA/SE) for each cell is halved, and the intensity can be tracked with a flow cytometer. Two strains of bacteria, Comamonas sp. strain DA001 and Acidovorax sp. strain OY-107, both isolated from a shallow aquifer, were utilized in this study. The change in the average generation or the average fluorescence intensity of the CFDA/SE-stained cells could be used to obtain estimates of doubling times. In microcosm experiments, the CFDA/SE-based doubling times were similar to the values calculated by total cell counting and were independent of cell concentration. Intact and repacked sediment core experiments with the same bacteria indicated that changes in groundwater chemistry were just as important as growth rates in determining planktonic cell concentrations. The growth rates within the sediment cores were similar to those calculated in microcosm experiments, and preferential transport of the daughter cells was not observed. The experiments indicated that the growth rates could be determined in systems with cell losses due to other phenomena, such as attachment to sediment or predation. Application of this growth rate estimation method to data from a field-scale bacterial transport experiment indicated that the doubling time was approximately 15 days, which is the first known direct determination of an in situ growth rate for bacteria in an aquifer.

Homoepitaxial Growth Rate Studies on Diamond (110), (111), and (100) Surfaces in a Hot-Filament Reactor

1992 ◽  
Vol 270 ◽  
Author(s):  
C. Judith Chu ◽  
Benjamin J. Bai ◽  
Norma J. Komplin ◽  
Donald E. Patterson ◽  
Mark P. D'evelyn ◽  
...  
Keyword(s):  
Growth Rate ◽  
Substrate Temperature ◽  
Growth Rates ◽  
Radical Mechanism ◽  
Effective Activation ◽  
Methyl Radical ◽  
Kcal Mole ◽  
Hot Filament ◽  
Substrate Temperatures ◽  
Methane Concentrations

ABSTRACTGrowth rates of homoepitaxial (110), (111), and (100) diamond films were experimentally determined, for the first time, in a hot filament reactor using methane and carbon tetrachloride as the carbon source. Methane concentrations from 0.07 % to 1.03 % in H2 were studied at a substrate temperature of 970°C. Growth rates were found to be crystal-face dependent with respect to methane concentration, being linear or first order for the (100)-orientation, sublinear for (110), and sigmoidal for (111). The observed growth kinetics of (111) suggest the viability of an acetylene mechanism for (111), along with the methyl radical mechanism at methane concentrations above 0.73%. CC14 concentrations from 0.06% to 0.69% in H2 were also investigated at a substrate temperature of 970°C. Growth rate behavior was similar to that of methane for all three crystal faces.The temperature dependence of the growth rates was also crystal-orientation dependent. At substrate temperatures above 730°C, growth rates are thought to be mainly transport limited, yielding effective activation energies of 8±3, 18±2, and 12±4 kcal/mole for (100), (110), and (111) orientations, respectively. At substrate temperatures below 730°C, growth rates are thought to be surface reaction rate-limited, with an overall effective activation energy of 50±19 kcal/mole for the three crystal-orientations studied.

scholarly journals Point defect incorporation during diamond chemical vapor deposition

1999 ◽  
Vol 14 (8) ◽  
pp. 3439-3446 ◽  
Author(s):  
C. C. Battaile ◽  
D. J. Srolovitz ◽  
J. E. Butler
Keyword(s):  
Growth Rate ◽  
Substrate Temperature ◽  
Kinetic Monte Carlo ◽  
Chemical Vapor ◽  
Atomic Scale ◽  
Diamond Growth ◽  
Gas Composition ◽  
Atom Concentration ◽  
Kinetic Monte Carlo Simulations ◽  
Diamond Chemical Vapor Deposition

The incorporation of vacancies, H atoms, and sp2 bond defects into single-crystal homoepitaxial (100) (2 × 1)–and (111)-oriented chemical-vapor-deposited diamond was simulated by atomic-scale kinetic Monte Carlo. Simulations were performed for substrate temperatures from 600 to 1200 °C with 0.4% CH4 in the feed gas, and for 0.4–7% CH4 feeds with a substrate temperature of 800 °C. The concentrations of incorporated H atoms increased with increasing substrate temperature and feed gas composition, and sp2 bond trapping increased with increasing feed gas composition. Vacancy concentrations were low under all conditions. The ratio of growth rate to H atom concentration was highest around 800–900°C, and the growth rate to sp2 ratio was maximum around 1% CH4, suggesting that these conditions are ideal for economical diamond growth under simulated conditions.

The Role of Heavy Hydrocarbons in Cvd Diamond Growth

1992 ◽  
Vol 270 ◽  
Author(s):  
Ching-Hsong Wu ◽  
T. J. Potter ◽  
M. A. Tamor
Keyword(s):  
Growth Rate ◽  
Cvd Diamond ◽  
Diamond Growth ◽  
Spectrometric Analysis ◽  
Heavy Hydrocarbons ◽  
Hot Filament Cvd ◽  
Hot Filament ◽  
Deposition Conditions

ABSTRACTA mass spectrometric analysis of heavy hydrocarbons (HHCs) during hot-filament CVD diamond growth was performed together with in situ monitoring of the growth rate. Many HHCs were detected and tentatively identified. Of all HHCs studied, only diacetylene shows good correlation with the diamond growth rate under various deposition conditions. Its possible role is discussed.

scholarly journals Disparities between <i>Phaeocystis</i> in situ and optically-derived carbon biomass and growth rates: potential effect on remote-sensing primary production estimates

2014 ◽  
Vol 11 (4) ◽  
pp. 6119-6149
Author(s):  
L. Peperzak ◽  
H. J. van der Woerd ◽  
K. R. Timmermans
Keyword(s):  
Growth Rate ◽  
Quantum Efficiency ◽  
Growth Rates ◽  
Standing Stock ◽  
Phytoplankton Growth ◽  
Ex Situ ◽  
Fluorescent Light ◽  
Limited Growth ◽  
Global Carbon

Abstract. The oceans play a pivotal role in the global carbon cycle. Unfortunately, the daily production of organic carbon, the product of phytoplankton standing stock and growth rate cannot be measured globally by discrete oceanographic methods. Instead, optical proxies from Earth-orbiting satellites must be used. To test the accuracy of optically-derived proxies of phytoplankton physiology and growth rate, standard ex situ data from the wax and wane of a Phaeocystis bloom in laboratory mesocosms were compared with hyperspectral reflectance data. Chlorophyll biomass could be estimated accurately from reflectance using specific chlorophyll absorption algorithms. However, the conversion of chlorophyll (Chl) to carbon (C) was obscured by the observed increase in C : Chl under nutrient-limited growth. C : Chl was inversely correlated (r2 = 0.88) with Photosystem II quantum efficiency (Fv/Fm), the in situ fluorometric oceanographic proxy for growth rate. In addition, the optical proxy for growth rate, the quantum efficiency of fluorescence &amp;varphi; was linearly correlated to Fv/Fm (r2 = 0.84), but not – as by definition – by using total phytoplankton absorption, because during nutrient-limited growth the concentrations of non-fluorescent light-absorbing pigments increased. As a consequence, none of the three proxies (C : Chl, Fv/Fm, φ) was correlated to carbon or cellular phytoplankton growth rates. Therefore, it is concluded that although satellite derived estimates of chlorophyll biomass may be accurate, physiologically-induced non-linear shifts in growth rate proxies may obscure accurate phytoplankton growth rates and hence global carbon production estimates.

Diamond Growth Rates and Quality: Dependence on Gas Phase Composition

1994 ◽  
Vol 339 ◽  
Author(s):  
William D. Cassidy ◽  
Edward A. Evans ◽  
Yaxin Wang ◽  
John C. Angus ◽  
Peter K. Bachmann ◽  
...  
Keyword(s):  
Growth Rates ◽  
Diamond Surface ◽  
Diamond Growth ◽  
Gas Composition ◽  
Chemical Potentials ◽  
Co Concentration ◽  
The Stability ◽  
Hot Filament ◽  
Tie Line

ABSTRACTDiamond growth rates and quality were studied as a function of source gas composition and correlated with position on the ternary C-H-O diagram. The chemical potentials of carbon and oxygen change dramatically on either side of the H2-CO tie line, leading to large differences in the equilibrium distribution of species. These differences are reflected in the species flux reaching the diamond surface, and hence in the quality and growth rate of the diamond. In situ microbalance measurements in a hot-filament reactor show that the reaction rate is independent of the CO concentration, but decreases with increasing O2. Quality, as measured by Raman spectroscopy, increases as the C/C+O ratio in the source gases is reduced to approach the critical value of 0.5. The stability of the filaments to decarburizing and oxidation are correlated with the carbon and oxygen chemical potentials and hence to the position on the C-H-O diagram. A preliminary ternary diagram for the C-H-F system is presented.

Growth rates of dinoflagellates along the Karachi coast assessed by the size fractionation method

2015 ◽  
Vol 44 (3) ◽  
Author(s):  
Sonia Munir ◽  
Pirzada Jamal Ahmed Siddiqui ◽  
Tahira Naz ◽  
Zaib Un-nisa Burhan ◽  
Steve L. Morton
Keyword(s):  
Growth Rate ◽  
Growth Rates ◽  
In Situ Growth ◽  
Size Fractionation ◽  
Fractionation Method

AbstractThe in situ growth rates of dinoflagellates along the Karachi coast off Pakistan was studied by the size fractionated method during winter (February 2006) and summer (May 2007). The growth rate per day ranged from -2.87 to 2.3 d

Sign in / Sign up

Export Citation Format

Share Document