Room temperature recrystallization of nanocrystalline thin copper foils

1994 ◽  
Vol 362 ◽  
Author(s):  
J. Dille ◽  
J.-L. Delplancke ◽  
J. Charlier ◽  
R. Winand
Keyword(s):  
Electron Microscopy ◽  
Diffraction Pattern ◽  
Room Temperature ◽  
Structural Evolution ◽  
Preferential Orientation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Copper Foils ◽  
Different Temperatures ◽  
Anodized Titanium

AbstractThin copper foils (100 micrometers thick) are produced by electrolysis on anodized titanium substrates. A sharp distribution of grain diameter is observed around 200 nanometers. The X-ray diffraction pattern shows a slight preferential orientation of the crystals with the (111) planes parallel to the substrate. This X-ray diffraction pattern evolves at room temperature. After 60 days, a preferential orientation of the (200) planes parallel to the substrate is observed. This effect is associated with the recrystallisation of the foil with growth of large copper grains (diameter higher than 5 micrometers) as observed by high resolution transmission electron microscopy.The structural evolution of the copper foils is studied by electron microscopy, X-ray and electron diffractions at different temperatures.The mechanical properties of the foils are also studied as a function of time after electrodeposition.

scholarly journals Highly ordered polyaniline as an efficient dye remover

2017 ◽  
Vol 36 (1-2) ◽  
pp. 429-440 ◽  
Author(s):  
Pinki Chakraborty ◽  
Aman Kothari ◽  
Rajamani Nagarajan
Keyword(s):  
Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Diffraction Pattern ◽  
Fourier Transform Infrared Spectroscopy ◽  
Room Temperature ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Polyaniline was synthesized by the chemical oxidative polymerization procedure at room temperature employing hydrogen peroxide (H2O2) as oxidant and ferrous chloride (FeCl2·2H2O) and vanadyl sulphate (VOSO4·H2O) as co-catalysts, respectively. The obtained polymers were characterized by high resolution powder X-ray diffraction, Fourier transform infrared spectroscopy, Raman, UV–Visible, photoluminescence spectroscopy, thermogravimetric Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) techniques. Ordered arrangement indicative of semi-crystalline nature of polyaniline was evidenced from the presence of intense reflection at d = 13.72 Å in the powder X-ray diffraction pattern followed by two lesser intense peaks at 4.61 and 3.47 Å. Fourier transform infrared spectroscopy and Raman spectroscopic results indicated the polyaniline to be emeraldine salt form. Fibrous morphology was observed in scanning electron microscope images. Nearly 93% of Methyl Orange dye was adsorbed in 30 min by the ordered polyaniline at room temperature. No significant difference in the crystallinity and/or ordering was noticed in the powder X-ray diffraction pattern after dye adsorption. The correlation between the ordered structure of polyaniline and its higher adsorption property derived in the current study has the potential to fabricate devices consisting polyaniline to detect dye molecules.

Electron Microscopy of Human Gallstones

1971 ◽  
Vol 29 ◽  
pp. 296-297
Author(s):  
C. Wolpers ◽  
R. Blaschke
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Bile Pigment ◽  
X Ray Diffraction ◽  
Triclinic Crystal System ◽  
X Ray ◽  
Follow Up Study ◽  
Infra Red ◽  
Main Components

Scanning microscopy was used to study the surface of human gallstones and the surface of fractures. The specimens were obtained by operation, washed with water, dried at room temperature and shadowcasted with carbon and aluminum. Most of the specimens belong to patients from a series of X-ray follow-up study, examined during the last twenty years. So it was possible to evaluate approximately the age of these gallstones and to get information on the intensity of growing and solving.Cholesterol, a group of bile pigment substances and different salts of calcium, are the main components of human gallstones. By X-ray diffraction technique, infra-red spectroscopy and by chemical analysis it was demonstrated that all three components can be found in any gallstone. In the presence of water cholesterol crystallizes in pane-like plates of the triclinic crystal system.

Electron Microscopy of Shock Loaded Polycrystalline Beryllium

1974 ◽  
Vol 32 ◽  
pp. 506-507 ◽  
Author(s):  
J. M. Galbraith ◽  
L. E. Murr ◽  
A. L. Stevens
Keyword(s):  
Electron Microscopy ◽  
Wave Propagation ◽  
Structural Change ◽  
Single Crystal ◽  
Diffraction Pattern ◽  
Shock Loading ◽  
Slip Systems ◽  
Compression Tests ◽  
X Ray Diffraction ◽  
X Ray

Uniaxial compression tests and hydrostatic tests at pressures up to 27 kbars have been performed to determine operating slip systems in single crystal and polycrystal1ine beryllium. A recent study has been made of wave propagation in single crystal beryllium by shock loading to selectively activate various slip systems, and this has been followed by a study of wave propagation and spallation in textured, polycrystal1ine beryllium. An alteration in the X-ray diffraction pattern has been noted after shock loading, but this alteration has not yet been correlated with any structural change occurring during shock loading of polycrystal1ine beryllium.This study is being conducted in an effort to characterize the effects of shock loading on textured, polycrystal1ine beryllium. Samples were fabricated from a billet of Kawecki-Berylco hot pressed HP-10 beryllium.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Synthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons

2010 ◽  
Vol 97-101 ◽  
pp. 4213-4216
Author(s):  
Jian Xiong Liu ◽  
Zheng Yu Wu ◽  
Guo Wen Meng ◽  
Zhao Lin Zhan
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Vapour Deposition ◽  
Chemical Vapour ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Ceramic Boat

Novel single-crystalline SnO2 zigzag nanoribbons have been successfully synthesized by chemical vapour deposition. Sn powder in a ceramic boat covered with Si plates was heated at 1100°C in a flowing argon atmosphere to get deposits on a Si wafers. The main part of deposits is SnO2 zigzag nanoribbons. They were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and selected-area electron diffraction (SAED). SEM observations reveal that the SnO2 zigzag nanoribbons are almost uniform, with lengths near to several hundred micrometers and have a good periodically tuned microstructure as the same zigzag angle and growth directions. Possible growth mechanism of these zigzag nanoribbons was discussed. A room temperature PL spectrum of the zigzag nanoribbons shows three peaks at 373nm, 421nm and 477nm.The novel zigzag microstructures will provide a new candidate for potential application.

Influence of Silicon Nitride on Properties of Corundum Based Castable

2013 ◽  
Vol 634-638 ◽  
pp. 2358-2361
Author(s):  
Jun Cong Wei ◽  
Li Rong Yang
Keyword(s):  
Electron Microscopy ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Cold Strength ◽  
X Ray ◽  
Refractory Castables ◽  
Shock Resistance ◽  
Scanning Electron

The effects of Si3N4 addition on the room temperature physical properties and thermal shock resistance properties of corundum based refractory castables were investigated using brown corundum, white corundum and alumina micropowder as the starting materials and pure calcium aluminate as a binder. The phase composition, microstructure, mechanical properties of corundum based castables were investigated by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that as the increase in Si3N4 addition, the bulk density decreased and apparent porosity increased, the cold strength deduced. However, the residual strength rate increased. That is, the thermal shock resistance was improved. This is because even though the introduction of Si3N4 inhibited the sintering of material and deduced the compactness, microcracks were produced in the materials due to a difference in thermal expansion coefficient. So the thermal shock resistance of corundum based castable was improved.

N-type Ba0.2Co4Sb11.5Te0.5: Optimization of thermoelectric properties by different pressures

2019 ◽  
Vol 33 (03) ◽  
pp. 1950027 ◽  
Author(s):  
Jiaxiang Chen ◽  
Xiaopeng Jia ◽  
Yuewen Zhang ◽  
Haiqiang Liu ◽  
Baomin Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Absolute Value ◽  
X Ray ◽  
Coefficient Increase ◽  
Maximum Power Factor ◽  
Scanning Electron

The polycrystalline skutterudite [Formula: see text] were successfully synthesized from 1.5 GPa to 3.5 GPa by the high pressure and high temperature (HPHT) method. Negative Seebeck coefficient confirmed the n-type conductivity of all samples. The phase compositions of samples were investigated by X-ray diffraction (XRD) and the microstructures were observed by scanning electron microscopy (SEM). It was found that the grains appeared smaller and the grain boundaries became more abundant when pressures were higher. We measured the electrical properties from room temperature to 723 K. Both the electrical resistivity and absolute value of Seebeck coefficient increase with the increasing synthetic pressure. At 723 K, the maximum power factor of [Formula: see text] was obtained for the sample synthesized under 3 GPa. The maximum ZT value of 0.61 was reached by [Formula: see text] synthesized under 3 GPa and measured at 723 K.

Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part II. Phase Transformation and Microstructural Control

1998 ◽  
Vol 13 (9) ◽  
pp. 2588-2596 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Electron Microscopy ◽  
Pressureless Sintering ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Different Temperatures ◽  
Si3n4 Ceramics ◽  
Scanning Electron ◽  
Microstructural Control

The low temperature pressureless sintering of a nanosized Si3N4 powder with doped sintering additives was investigated. The microstructural evolution during sintering at different temperatures was analyzed using x-ray diffraction and scanning electron microscopy. The effect of using nanosized Si3N4 powder as a catalyst to accelerate the α→β–Si3N4 transformation of a commercial Si3N4 powder with larger particle sizes was also investigated. Finally, two stage sintering was used to study the feasibility of controlling the microstructure and the mechanical properties of the nanosized silicon nitride.

New method for the production of bulk amorphous materials of Nd–Fe–B alloys

2005 ◽  
Vol 20 (3) ◽  
pp. 563-566 ◽  
Author(s):  
Tetsuji Saito ◽  
Hiroyuku Takeishi ◽  
Noboru Nakayama
Keyword(s):  
Electron Microscopy ◽  
Amorphous Materials ◽  
Room Temperature ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons

We report a new compression shearing method for the production of bulk amorphous materials. In this study, amorphous Nd–Fe–B melt-spun ribbons were successfully consolidated into bulk form at room temperature by the compression shearing method. X-ray diffraction and transmission electron microscopy studies revealed that the amorphous structure was well maintained in the bulk materials. The resultant bulk materials exhibited the same magnetic properties as the original amorphous Nd–Fe–B materials.

Sign in / Sign up

Export Citation Format

Share Document