Synthesis and Structural Studies of Microporous Yttria-Stabilized Zirconia Ceramics

1996 ◽  
Vol 431 ◽  
Author(s):  
R. Srinivasan ◽  
D. E. Sparks ◽  
D. R. Milburn ◽  
B. H. Davis
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Diffraction Data ◽  
Yttria Stabilized Zirconia ◽  
Structural Studies ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Zirconia Ceramics ◽  
Narrow Pore Size Distribution ◽  
X Ray

AbstractYttria-stabilized zirconia was prepared by (i) coprecipitation and (ii) alkoxide hydrolysis. The thermal and X-ray diffraction data were compared. The coprecipitation method yields microporous materials after calcination at 500°C for 4 hours with a narrow pore size distribution at a radius of 2–2.5 nm. Similar results were also seen with the alkoxide hydrolysis.

High Porosity SiC Ceramics with a Narrow Pore Size Distribution

2008 ◽  
Vol 368-372 ◽  
pp. 840-842 ◽  
Author(s):  
Li Min Shi ◽  
Hong Sheng Zhao ◽  
Ying Hui Yan ◽  
Chun He Tang
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Phenolic Resin ◽  
High Porosity ◽  
X Ray Diffraction ◽  
Narrow Pore Size Distribution ◽  
X Ray ◽  
Sic Ceramics ◽  
Porous Sic

Using the coat mix process, porous SiC ceramics are fabricated using commercially available silicon powders and phenolic resin as the starting materials. The phase composition, morphology, pore size and pore size distribution of the obtained products are characterized by X-ray diffraction, scanning electron microscopy and mercury intrusion porosimeter. The results show that high porosity SiC ceramics with a narrow pore size distribution can be fabricated at 1500°C in vacuum by the coat mix process. The open pore porosity can reach up to 60%. The pore size varies in the range of 1-6 'm.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

Effect of Yttria-Stabilized Zirconia Concentration in an Electroless Bath on Microstructure and Composition of Ni/Yttria-Stabilized Zirconia Nanocomposite

2021 ◽  
Vol 21 (11) ◽  
pp. 5592-5602
Author(s):  
Samira Almasi ◽  
Ali Mohammad Rashidi
Keyword(s):  
High Performance ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Nickel Ion ◽  
Nanocomposite Particles ◽  
X Ray ◽  
Ni Content ◽  
Naoh Solution ◽  
Average Size

The effect of the yttria-stabilized zirconia (YSZ) nanoparticle loading in an electro-less bath was considered as one of the vital synthesis variables for control Ni content and microstructure of prepared nanocomposite particles, which are two crucial factors to achieving high-performance SOFC anode. Nanocomposite particles were prepared using a simple electroless method without any expensive pretreatment of sensitizing by Sn2+ ions as well as activating by Pd2+ ions that are usually used to apply nickel coating on the surface of a non-conductive substrate. The process was performed by adding YSZ nanoparticles into NaOH solution, separating them from the solution by the centrifugal method, then providing several water-based nanofluids with different concentrations of activated YSZ nanoparticles, mixing them with NiCI2 solution, followed by adding the hydrazine and then NaOH solution. X-ray diffraction and scanning electron microscopy coupled with energy dispersive X-ray analysis were used to analyze the prepared nanocomposite particles. It is observed that after adding YSZ nanoparticles into the NaOH solution, the pH of the solution varied gradually from a starting pH of 10.2 to 9. Also, by increasing the YSZ nanoparticles loading in the electroless bath from 76 mg/l to 126 mg/l, the grain size of Ni deposits, the Ni content and the average size of the prepared nanocomposite particles decreased. The electrochemical mechanism previously proposed for the nickel ion reduction was modified, and a novel analytical model was proposed for variation of the efficiency of Ni deposition with YSZ nanoparticles loading.

EPITAXIAL GROWTH OF YTTRIA-STABILIZED ZIRCONIA FILMS ON SILICON BY R.F. MAGNETRON SPUTTERING

1991 ◽  
Vol 05 (27) ◽  
pp. 1829-1835 ◽  
Author(s):  
Q.X. SU ◽  
L. LI ◽  
Y.Y. ZHAO ◽  
Y.Z. ZHANG ◽  
P. XU
Keyword(s):  
Magnetron Sputtering ◽  
Yttria Stabilized Zirconia ◽  
Processing Conditions ◽  
Full Width ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Si Substrates ◽  
Zirconia Films ◽  
Scanning Electron

Yttria-stabilized Zirconia(YSZ) films were deposited on (100)Si substrates by R.F. magnetron sputtering method. X-ray diffraction analysis showed that the best YSZ films were cubic in structure and was grown epitaxially with (100) orientation. The (200) peak of YSZ films was 0.8° of the full width at half of the maximum, X-ray diffraction based on Seemann-Bohlin focusing geometry showed no peaks. The morphology of the YSZ films was observed by scanning electron microscopy. The effects of the processing conditions (such as substrate temperature, oxygen partial pressure, etc.) on the structure of the film were also discussed.

Synchrotron radiation study of yttria-stabilized zirconia, Zr0.758Y0.242O1.879

1999 ◽  
Vol 55 (5) ◽  
pp. 726-735 ◽  
Author(s):  
N. Ishizawa ◽  
Y. Matsushima ◽  
M. Hayashi ◽  
M. Ueki
Keyword(s):  
Synchrotron Radiation ◽  
Single Crystal ◽  
Yttria Stabilized Zirconia ◽  
Data Sets ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Ideal Position ◽  
Fluorite Type ◽  
The Ideal

The fluorite-related cubic structure of yttria-stabilized zirconia, Zr0.75 8Y0.24 2O1.87 9, has been studied by single-crystal X-ray diffraction using synchrotron radiation and by EXAFS. Two diffraction data sets obtained at X-ray energies of 512 and 10 eV below the Y K edge revealed that in the average structure Zr atoms are displaced from the origin of the space group Fm3¯m along 〈111〉 by 0.19 Å, while Y atoms reside at the origin. Approximately 48% of the O atoms occupy the ideal position in the fluorite-type structure, while 43% of O atoms are displaced from the ideal position along 〈001〉 by 0.31 Å. The remaining 9% of O atoms are presumably sited at interstitial positions. Local structures around Zr and Y are investigated by combining the results of single-crystal X-ray diffraction and EXAFS studies.

Fabrication of Porous YSZ from ZnO-YSZ Cermet

2007 ◽  
Vol 124-126 ◽  
pp. 235-238
Author(s):  
Moon Jin Hwang ◽  
Chong Soo Han
Keyword(s):  
Electron Microscope ◽  
Gas Permeability ◽  
Acid Leaching ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Scanning Electron Microscope Image ◽  
X Ray ◽  
Electron Microscope Image ◽  
Scanning Electron

Porous YSZ(8 mol% yttria-stabilized zirconia) was prepared by an acid leaching of ZnO-YSZ composite. The ZnO-YSZ composites were obtained by two different methods, a 1450 °C sintering of the mechanical mixture of ZnO and YSZ powders or a decomposition of Zn(NO3)2 deposited on YSZ and a subsequent sintering. The XRD (X-ray diffraction) pattern of the composite indicated that it was a mixture of ZnO and YSZ even after the sintering. Sharp edge or round edge of YSZ was observed in SEM (Scanning Electron Microscope) image of the porous-YSZ from the mixture of ZnO and YSZ, or Zn(NO3)2 deposited on YSZ, respectively. The porous YSZ from the composite having ZnO component greater than 60 wt% shows low mechanical strength. As the ZnO content of the composite increased, the porosity and gas permeability of the porous YSZ increased. From the result, it was suggested that ZnO is a candidate to generate pores in YSZ bulk or membrane.

Crystal data for ternary compounds of the system Cu–As2Se3

1987 ◽  
Vol 20 (4) ◽  
pp. 323-323
Author(s):  
C. A. Majid ◽  
M. A. Hussain
Keyword(s):  
Diffraction Data ◽  
Lattice Parameters ◽  
Structural Studies ◽  
Crystal Data ◽  
X Ray Diffraction ◽  
Space Group ◽  
X Ray ◽  
Ternary Compounds

Structural studies of polycrystalline CuAsSe2, Cu3AsSe4 and Cu3AsSe3 are reported. These were found to be cubic with space group Pm{\bar 3}m and lattice parameters as follows: (1) CuAsSe2: a = 5.513(4) Å, V = 167.47(1) Å3, Z = 2; Dm = 5.56(6), Dx = 5.88 g cm−3. (2) Cu3AsSe4: a = 5.530(5) Å; V = 169.11(2) Å3; Z = 1; Dm = 5.51(5), Dx = 5.75 g cm−3. (3) Cu3AsSe3: a = 5.758(9) Å, V = 190.87(3) Å3, Z = 1, Dm = 5.03(9), Dx = 4.45 g cm−3. X-ray diffraction data using a Rigaku DMAX-IIIA diffractometer and Cu Kα radiation.

Synthesis of Yttria-Stabilised Zirconia Matrices for Immobilisation of Actinides by Internal Gelation Method

2007 ◽  
Author(s):  
G. Benay ◽  
G. Modolo ◽  
R. Odoj
Keyword(s):  
Electron Microscopy ◽  
Spent Nuclear Fuel ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Internal Gelation ◽  
X Ray ◽  
Remote Handling ◽  
Co Conversion ◽  
Formation Of Cracks

In the scope of the co-conversion of actinides solutions obtained from partitioning spent nuclear fuel, the internal gelation of ceria-doped yttria-stabilized zirconia was investigated. This dust-free method to fabricate kernels, which can be used as fuel or pressed into pellets, is technically easy to implement and compatible with remote handling. The effects of the quantity of reactants used on the properties of the material were studied. Gels, kernels and pellets were analyzed by thermal analysis, electron microscopy and X-ray diffraction. It was found that the initial broth composition played an important role in the structure of kernels and the formation of cracks during thermal treatment. Pellets obtained with a repressing method were found to present densities up to 86% TD.

Sign in / Sign up

Export Citation Format

Share Document