Electrical Characterization Of Nitrogen Acceptors In p-ZnSe/p-GaAs Grown By Molecular Beam Epitaxy

1996 ◽  
Vol 442 ◽  
Author(s):  
D. Seghier ◽  
H.P. Gislason
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Deep Level ◽  
Energy Levels ◽  
Reverse Current ◽  
Electrical Characterization ◽  
Growth Conditions ◽  
Current Voltage ◽  
Major Interest ◽  
Transient Spectroscopy

AbstractUsing current-voltage measurements, deep-level transient spectroscopy and admittance spectroscopy we investigated nitrogen doped ZnSe grown on p-GaAs substrates by molecular beam epitaxy. Three major hole traps were observed with energy levels at 0. 11, 0.46, and 0.56 eV from the valence band. We attribute the level at 0.11 eV to a nitrogen acceptor. No other direct observations of this important acceptor level in p-ZnSe have been reported in the literature so far. The two remaining levels may originate from the nitrogen doping process. In addition, reverse current-voltage characteristics of the ZnSe/GaAs heterojunction show a hysteresis at low temperature and a soft saturation. At a constant reverse bias the current increases slowly until it reaches a steady state value. This behavior is attributed to a slow voltage-induced barrier lowering due to the presence of mismatch interface states. Therefore, these analyses are of a major interest for applications of ZnSe/GaAs based devices and illustrates the necessity of improving the growth conditions of such structures.

Electrical Characterization of Sputter Deposition Induced Defects in n-GaN

1998 ◽  
Vol 537 ◽  
Author(s):  
F. D. Auret ◽  
S. A. Goodman ◽  
F. K. Koschnick ◽  
J.-M. Spaeth ◽  
B. Beaumont ◽  
...  
Keyword(s):  
Barrier Height ◽  
Deep Level ◽  
Energy Levels ◽  
Reverse Current ◽  
Electrical Characterization ◽  
Sputter Deposition ◽  
Nitrogen Vacancy ◽  
Transient Spectroscopy ◽  
Sputter Deposited ◽  
Induced Defects

AbstractWe have used current-voltage (I-V) measurements to assess and compare the electrical characteristics of resistively evaporated and sputter deposited Au Schottky contacts on epitaxially grown GaN. These I-V measurements revealed that resistively deposited Au contacts exhibited excellent rectification properties: high barrier height, low reverse current and good ideality factor (n = 1.04). In contrast, sputter deposited contacts had poor characteristics: low barrier height, high reverse current and non-linear forward I-V characteristics. The cause of this is thought to be defects introduced at and near the surface during sputter deposition. Deep level transient spectroscopy (DLTS) showed that at least four defects, with energy levels at 0.22±0.02 eV, 0.30±0.01 eV, 0.40±0.01 eV and 0.45±0.10 eV below the conduction band, were introduced in the GaN during sputter deposition. The first of these defects has similar electronic properties as a radiation induced defect in GaN, speculated to be the nitrogen vacancy, while the second appears to be the same as a defect in the as-grown material. The latter two defects have not previously been observed in as-grown or processed epitaxial GaN.

scholarly journals Electrical Characterization of Sputter Deposition Induced Defects in n-GaN

1999 ◽  
Vol 4 (S1) ◽  
pp. 612-617 ◽  
Author(s):  
F. D. Auret ◽  
S. A. Goodman ◽  
F. K. Koschnick ◽  
J.-M. Spaeth ◽  
B. Beaumont ◽  
...  
Keyword(s):  
Barrier Height ◽  
Deep Level ◽  
Energy Levels ◽  
Reverse Current ◽  
Electrical Characterization ◽  
Sputter Deposition ◽  
Nitrogen Vacancy ◽  
Transient Spectroscopy ◽  
Sputter Deposited ◽  
Induced Defects

We have used current-voltage (I-V) measurements to assess and compare the electrical characteristics of resistively evaporated and sputter deposited Au Schottky contacts on epitaxially grown GaN. These I-V measurements revealed that resistively deposited Au contacts exhibited excellent rectification properties: high barrier height, low reverse current and good ideality factor (n = 1.04). In contrast, sputter deposited contacts had poor characteristics: low barrier height, high reverse current and non-linear forward I-V characteristics. The cause of this is thought to be defects introduced at and near the surface during sputter deposition. Deep level transient spectroscopy (DLTS) showed that at least four defects, with energy levels at 0.22±0.02 eV, 0.30±0.01 eV, 0.40±0.01 eV and 0.45±0.10 eV below the conduction band, were introduced in the GaN during sputter deposition. The first of these defects has similar electronic properties as a radiation induced defect in GaN, speculated to be the nitrogen vacancy, while the second appears to be the same as a defect in the as-grown material. The latter two defects have not previously been observed in as-grown or processed epitaxial GaN.

scholarly journals Correlation between Defects and Electrical Performances of Ion-Irradiated 4H-SiC p–n Junctions

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1966
Author(s):  
Domenico Pellegrino ◽  
Lucia Calcagno ◽  
Massimo Zimbone ◽  
Salvatore Di Franco ◽  
Antonella Sciuto
Keyword(s):  
Deep Level ◽  
Electrical Characterization ◽  
High Fluence ◽  
Defect States ◽  
Exponential Parameter ◽  
Current Voltage ◽  
Different Temperatures ◽  
In Series ◽  
Transient Spectroscopy ◽  
Fluence Range

In this study, 4H-SiC p–n junctions were irradiated with 700 keV He+ ions in the fluence range 1.0 × 1012 to 1.0 × 1015 ions/cm2. The effects of irradiation were investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements, while deep-level transient spectroscopy (DLTS) was used to study the traps introduced by irradiation defects. Modifications of the device’s electrical performances were observed after irradiation, and two fluence regimes were identified. In the low fluence range (≤1013 ions/cm2), I–V characteristics evidenced an increase in series resistance, which can be associated with the decrease in the dopant concentration, as also denoted by C–V measurements. In addition, the pre-exponential parameter of junction generation current increased with fluence due to the increase in point defect concentration. The main produced defect states were the Z1/2, RD1/2, and EH6/7 centers, whose concentrations increased with fluence. At high fluence (>1013 ions/cm2), I–V curves showed a strong decrease in the generation current, while DLTS evidenced a rearrangement of defects. The detailed electrical characterization of the p–n junction performed at different temperatures highlights the existence of conduction paths with peculiar electrical properties introduced by high fluence irradiation. The results suggest the formation of localized highly resistive regions (realized by agglomeration of point defects) in parallel with the main junction.

Traps in Si-doped AlxGa1-xN Grown by Molecular Beam Epitaxy on Sapphire Characterized by Deep Level Transient Spectroscopy

2006 ◽  
Vol 955 ◽  
Author(s):  
Mo Ahoujja ◽  
S Elhamri ◽  
M Hogsed ◽  
Y. K. Yeo ◽  
R. L. Hengehold
Keyword(s):  
Molecular Beam Epitaxy ◽  
Deep Level Transient Spectroscopy ◽  
Molecular Beam ◽  
Deep Level ◽  
Unknown Origin ◽  
Shallow Donor ◽  
Related Point ◽  
Line Defects ◽  
Si Doped ◽  
Transient Spectroscopy

ABSTRACTDeep levels in Si doped AlxGa1−xN samples, with Al mole fraction in the range of x = 0 to 0.30, grown by radio-frequency plasma activated molecular beam epitaxy on sapphire substrates were characterized by deep level transient spectroscopy (DLTS). DLTS measurements show two significant electron traps, P1 and P2, in AlGaN at all aluminum mole fractions. The electron trap, P2, appears to be a superposition of traps A and B , both of which are observed in GaN grown by various growth techniques and are thought to be related to VGa-shallow donor complexes. Trap P1 is related to line defects and N-related point defects. Both of these traps are distributed throughout the bulk of the epitaxial layer. An additional trap P0 which was observed in Al0.20Ga0.80N and Al0.30Ga0.70N is of unknown origin, but like P1 and P2, it exhibits dislocation-related capture kinetics. The activation energy measured from the conduction band of the defects is found to increase with Al mole content, a behavior consistent with other III-V semiconductors.

Study of Substrate Induced Deep Level Defects in Bulk GaN Layers Grown by Molecular Beam Epitaxy Using Deep Level Transient Spectroscopy

2011 ◽  
Vol 295-297 ◽  
pp. 777-780 ◽  
Author(s):  
M. Ajaz Un Nabi ◽  
M. Imran Arshad ◽  
Adnan Ali ◽  
M. Asghar ◽  
M. A Hasan
Keyword(s):  
Molecular Beam Epitaxy ◽  
Deep Level Transient Spectroscopy ◽  
Molecular Beam ◽  
Deep Level ◽  
Diffusion Mechanism ◽  
Electron Trap ◽  
Si Substrate ◽  
Bulk Gan ◽  
Related Defect ◽  
Transient Spectroscopy

In this paper we have investigated the substrate-induced deep level defects in bulk GaN layers grown onp-silicon by molecular beam epitaxy. Representative deep level transient spectroscopy (DLTS) performed on Au-GaN/Si/Al devices displayed only one electron trap E1at 0.23 eV below the conduction band. Owing to out-diffusion mechanism; silicon diffuses into GaN layer from Si substrate maintained at 1050°C, E1level is therefore, attributed to the silicon-related defect. This argument is supported by growth of SiC on Si substrate maintained at 1050°C in MBE chamber using fullerene as a single evaporation source.

Electrical Characterization of N+-implanted n-type ZnO Single Crystals: p-n Homojunction and Deep Level Defects

2007 ◽  
Vol 1035 ◽  
Author(s):  
Qilin Gu ◽  
Xuemin Dai ◽  
Chi-Chung Ling ◽  
Shijie Xu ◽  
Liwu Lu ◽  
...  
Keyword(s):  
Single Crystals ◽  
Thermal Evolution ◽  
Deep Level ◽  
Schottky Diodes ◽  
Control Sample ◽  
Electrical Characterization ◽  
Type Layer ◽  
Current Voltage ◽  
Transient Spectroscopy ◽  
Induced Defects

AbstractUnintentionally doped n-type ZnO single crystals were implanted by nitrogen ions with different fluences of 1013, 1014 and 1015 cm−2 respectively. ZnO p-n homojunction was successfully fabricated due to the formation of p-type layer after 650°C post-implantation annealing in air for 30 minutes. Further thermal evolution of deep level defects was studied through thermal annealing up to 1200°C. Electrical characterization techniques including current-voltage (I-V), capacitance-voltage (C-V), Deep Level Transient Spectroscopy (DLTS) and double-correlation DLTS (DDLTS) were used for investigating the control sample, all the as-implanted and annealed samples through Au/n-ZnO Schottky diodes as well as ZnO p-n junctions. Detailed electrical properties of fabricated devices and characteristics of implantation induced defects were analyzed based on plentiful DLTS spectra. Moreover, low-temperature photoluminescence experiments of all the as-implanted and annealed samples were performed and the correlation between results from electrical and optical characterizations was discussed.

scholarly journals Electrical Characterization of Metastable Defects Introduced in GaN by Eu-Ion Implantation

2011 ◽  
Vol 679-680 ◽  
pp. 804-807 ◽  
Author(s):  
F. Danie Auret ◽  
Walter E. Meyer ◽  
M. Diale ◽  
P.J. Janse Van Rensburg ◽  
S.F. Song ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Deep Level ◽  
Energy Levels ◽  
Electrical Characterization ◽  
Defect States ◽  
First Order Kinetics ◽  
Transient Spectroscopy ◽  
Induced Defects ◽  
Transformation Processes

Gallium nitride (GaN), grown by HVPE, was implanted with 300 keV Eu ions and then annealed at 1000 oC . Deep level transient spectroscopy (DLTS) and Laplace DLTS (L-DLTS) were used to characterise the ion implantation induced defects in GaN. Two of the implantation induced defects, E1 and E2, with DLTS peaks in the 100 – 200 K temperature range, had DLTS signals that could be studied with L-DLTS. We show that these two defects, with energy levels of 0.18 eV and 0.27 eV below the conduction band, respectively, are two configurations of a metastable defect. These two defect states can be reproducibly removed and re-introduced by changing the pulse, bias and temperature conditions, and the transformation processes follow first order kinetics.

THE STUDY OF Al0.29Ga0.71N-BASED SCHOTTKY PHOTODIODES GROWN ON SILICON BY PLASMA-ASSISTED MOLECULAR BEAM EPITAXY

2013 ◽  
Vol 27 (12) ◽  
pp. 1350085
Author(s):  
M. Z. MOHD YUSOFF ◽  
Z. HASSAN ◽  
C. W. CHIN ◽  
H. ABU HASSAN ◽  
M. J. ABDULLAH ◽  
...  
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Electrical Characterization ◽  
Rf Plasma ◽  
Yellow Emission ◽  
Band Edge Emission ◽  
Current Voltage ◽  
Standard Value ◽  
Schottky Photodiode

In this paper, the growth and characterization of epitaxial Al 0.29 Ga 0.71 N grown on Si (111) by RF-plasma assisted molecular beam epitaxy (MBE) are described. The Al mole fraction was derived from the HR-XRD symmetric rocking curve (RC) ω/2θ scans of (0002) plane as x = 0.29. PL spectrum of sample has shown sharp and intense band edge emission of GaN without the existence of yellow emission band, showing that it is comparable in crystal quality of the sample when compared with previous reports. From the Raman measurement of as-grown Al 0.29 Ga 0.71 N layer on GaN / AlN / Si sample. We found that the dominant E 2 (high) phonon mode of GaN appears at 572.7 cm-1. The E 2 (high) mode of AlN appears at 656.7 cm-1 and deviates from the standard value of 655 cm-1 for unstrained AlN . Finally, AlGaN Schottky photodiode have been fabricated and analyzed by mean of electrical characterization, using current–voltage (I–V) measurement to evaluate the performance of this device.

Sign in / Sign up

Export Citation Format

Share Document