scholarly journals Changes in occlusal vertical dimension in microwave processing of complete dentures

2002 ◽  
Vol 13 (3) ◽  
pp. 197-200 ◽  
Author(s):  
Débora Barros Barbosa ◽  
Marco Antonio Compagnoni ◽  
Cláudio Rodrigues Leles

This study investigated the effect of different microwave curing cycles on the changes in occlusal vertical dimension of complete dentures. Four test groups with 12 maxillary dentures each were evaluated. Groups 1, 2 and 3 were polymerized with different cycles by microwave radiation and Group 4 was the control and cured by water bath. The average pin opening for all groups was less than 0.5 mm. There was no significant difference between the groups polymerized by the microwave method and the control group. However, analyses of the vertical dimension changes showed statistically significant differences between groups 2 (0.276 ± 0.141 mm) and 3 (0.496 ± 0.220 mm).

2021 ◽  
Vol 76 (09) ◽  
pp. 517-523
Author(s):  
Sibusiso Rockfort Mthethwa ◽  
Lesibana Godfrey Maguga

The movement of teeth during processing of complete dentures disturbs the harmonious occlusal scheme established at the final wax try-in stage. Aims and objectives: to investigate the effect of RS flask closure on occlusal vertical dimensions of complete dentures. The mean occlusal vertical dimension of complete maxillary and mandibular dentures fabricated by the conventional flask closure were measured and compared with that of dentures fabricated by RS flask closure. Design: A pre-test post-test control group experimental design. Methods: Thirty sets of complete maxillary and mandibular wax trial dentures were randomly assigned to experimental groups. Fifteen sets were assigned to conventional flask closure and the remainder to RS flask closure. Compression molding with a long curing cycle was performed for the processing of the dentures. Pre-processing and post-processing occlusal vertical dimensions were determined. Results: The mean occlusal vertical dimensions of wax trial dentures assigned to either group were similar. The data produced substantial evidence to reject the null hypothesis that the post-processing mean occlusal vertical dimensions of both groups were equal. Conclusion: The occlusal vertical dimensions produced by dentures clamped by the RS flask closure were significantly less than those produced by dentures clamped by the conventional flask closure. 


2018 ◽  
Vol 21 (1) ◽  
pp. 26 ◽  
Author(s):  
Hatice Miray Uyan ◽  
Keziban Olcay ◽  
Mutlu Özcan

<p><strong>Objective:</strong> This study was designed to evaluate postoperative pain after endodontic retreatment. <strong>Material and Methods:</strong> Asymptomatic, multi-rooted molar &amp; premolar teeth requiring retreatment with 2–5 mm periapical lesions were included. Seventy-eight teeth were randomly placed in four groups (n=20): single-visit (control, group 1), Ledermix (group 2), metronidazole, ciprofloxacin, minocycline mixture (group 3), calcium hydroxide (group 4). The postoperative pain was recorded using a VAS at 6, 12, 24, and 48 h after retreatment. Statistical evaluation was performed using Two-Way Repeated Measures ANOVA and Tukey test. <strong>Results:</strong> Mild pain occurred in 67.5%, moderate in 30%, and flare-ups in 2.5%, and there was a significant difference between the groups (p&lt;0.01). Significantly lower postoperative pain was observed in TAP and CaOH<sub>2 </sub>groups(p&lt;0.05). In the 6, 12, and 24 h intervals, there was a significant difference in the pain levels (p&lt;0.05). <strong>Conclusion:</strong> TAP and CaOH<sub>2</sub> are effective for reducing postoperative pain after retreatment.</p><p><strong>Keywords</strong></p><p>Intracanal medicaments; Multiple-visit; Postoperative pain; Retreatment; Single-visit.</p>


2016 ◽  
Vol 88 (1) ◽  
pp. 56 ◽  
Author(s):  
Mehmet Zeynel Keskin ◽  
Salih Budak ◽  
Saim Gubari ◽  
Kalender Durmaz ◽  
Mehmet Yoldas ◽  
...  

Objectives: There are a number of studies about the effect of cigarette and alcohol on semen parameters in the literature. There is not a consensus on the relationship between use of cigarette and alchol and semen parameters in those studies. The number of studies in which cigarette and alcohol use are evaluated together is limited. This study was aimed to analyze the effect of cigarette and/or alcohol use on semen parameters. Methods: In this prospective study, 762 patients who applied to an hospital urology polyclinic between January 2015 and March 2015 due to infertility, were questioned for alcohol and cigarette use in anamnesis. The remaining 356 patients were included in our study. Then, semen analysis of the patients was performed. The patients were divided into five groups according to cigarette use, into five groups according to alcohol use and into four groups according to cigarette and/or alcohol use. Significant differences were analyzed between the groups in terms of semen volume, semen concentration, total motility, forward motility and morphological (normality, head anomaly, neck anomaly, tail anomaly) values. Results: According to cigarette use, only in group 4 (who use more than 20 package-years cigarette) semen volume was significantly lower than the control group (Mann-Whitney U, p = 0.009). There was no significant difference in any of the other parameters and groups compared with the control group (Mann-Whitney U, p &gt; 0,05) Conclusion:According to our study, using more than 20 package- years cigarette decreases semen volume. The reason of this result might be the fact that the threshold value, from which the effect of cigarette and alcohol use on the semen parameters has to be determined.


2020 ◽  
Vol 41 (S1) ◽  
pp. s518-s519
Author(s):  
Dayane Costa ◽  
Roel Castillo ◽  
Lillian Kelly Lopes ◽  
Anaclara Tipple ◽  
Honghua Hu ◽  
...  

Objectives: To evaluate the efficacy of double manual cleaning (DMC) with enzymatic followed by alkaline detergent for removing biofilm on hinged surgical instruments compared to automated cleaning by the washer-disinfector. Methods: Biofilm of Staphylococcus aureus (ATCC 25923) was formed in vitro on hemostatic forceps (Fig. 1). Biofilm-covered forceps were rinsed in distilled water and subjected to one of the following cleaning regimes (n = 5 forceps each): Group 1 forceps were soaked in sterile water for 5 minutes. Group 2-DMC forceps were soaked in enzymatic detergent, brushed 5 times on each face, rinsed with filtrated water (0.2 µm), soaked in alkaline detergent, brushed 5 times each face, rinsed with filtrated water (0.2 µm), and dried with sterile cloth. For group 3-DMC plus hinge inner brushing (n = 5), the forceps were soaked in detergents and brushed as in group 2, including hinge inner brushing (2-mm lumen brush) (Fig. 1). In group 4 (automated cleaning in a washer/disinfector), forceps were prewashed, washed once, washed again, rinsed, thermally rinsed, and dried. After the treatments, forceps were evaluated for microbial load (counting of colony-forming units), residual protein (BCA protein assay kit), and biofilm (scanning electron microscopy). Results: There was no statistically significant differences between the microbial load and protein level contaminating the forceps subjected to DMC (group 2) and the positive control group. The DMC with hinge inner brushing group (group 3) and the automated cleaning group (group 4) demonstrated a significantly reduced microbial load: reduction averages of 2.8 log 10 (P = .038) and 7.6 log10 (P ≤ .001), respectively. The protein level remaining on the forceps also significantly decreased: 2.563 μg (P = .016) and 1,453 μg (P = .001), respectively, compared to the positive control group. There was no statistically significant difference between DMC with hinge inner brushing and automated cleaning (groups 3 and 4) for all of the tests performed. None of the cleaning methods completely removed biofilm and/or soil from the forceps hinge internal region (Fig. 1). Conclusions: Automated cleaning had the best efficacy for removing biofilm. However, DMC with hinge inner brushing was an acceptable alternative cleaning method for sterilizing service units with only manual cleaning available, as is the case in most low- and middle-income countries. Neither automated nor any manual cleaning regimes were able to completely remove biofilm and soil from the forceps hinged area, and the amount of protein left after automated and DMC plus hinge brushing was higher than the recommended. Cleaning is the most important step for the reprocessing of reusable medical devices; thus, efforts must be undertaken to improve cleaning in different social and economic realities and scenarios.Funding: This study was supported by Coordenação de Aperfeiçoamento de Pessoal de Nível Superior – CAPES.Disclosures: None


2021 ◽  
Vol 14 (4) ◽  
pp. 1508-1513
Author(s):  
Ibraheem F Alshiddi

In order to assess the influence of finishing and polishing on the surface brightness and color stability of the ceramic veneer, fifty specimens were fabricated with 10 mm diameter and 2 mm thickness using IPS E-Max Ceramic. After glazing, 10 specimens were untouched as control group, and the other 40 specimens were abraded using 125µm diamond bur to create surface roughness. Forty specimens were divided into four groups (n=10), in group 1: specimens were finished using diamond point, in group 2 specimens’ surface was polished with a polishing kit, Group 3: Each specimen surface was polished with the polishing kit as in protocol 2 and was polished a polishing past and group 4 Each specimen was glazed by heating at 621℃ for 3 minutes followed by a temperature increase of 83℃/min up to 918℃ for 30 seconds. Color measurement was performed using spectrophotometer. Color stability data were analyzed using two-way ANOVA and Tukey’s HSD test (α=0.05). For Ra values, paired-samples t-tests were used to analyze the data and compare groups. The change in L and E showed a significant difference among the study groups; (group 1, group 2, group 3 and group 4) with respect to three variables L, a and b. A significant difference was noted when compared each group with the control; however, only group 2 showed a significant difference from group 4; the remaining groups demonstrated similar findings for all three variables. The study displayed a significant impact of the finishing and polishing technique on the surface brightness and color stability of ceramic restoration. However, it was evident that combination of two or three polishing techniques which includes polish kit and glaze enhances the surface finish and adds color stability by alternating the yellow – blue axis (increase in b) and red- green axis (decrease in a).


2004 ◽  
Vol 51 (1) ◽  
pp. 7-11
Author(s):  
Ljiljana Strajnic

One of the existing methods for analysis of the vertical dimension of occlusion or occlusal face height is the cephalometric analysis of the distance from nasion to menton (N-Me). The vertical dimension of occlusion was measured in 30 lateral cephalometric radiographs of edentulous patients (experimental group), with models of complete dentures after clinical methods of determining the vertical and horizontal intermaxillary relation and 30 lateral cephalometric radiographs of participants with natural teeth (control group). The aims of the present study were: to analyse the vertical dimension of occlusion in participants with natural teeth skeletal class I, to cephalometrically evaluate the reconstructing vertical dimension of occlusion of edentulous patients skeletal class I , to compare examined variables between individuals with natural teeth and edentulous patients. The results indicated a remarkable correlation in the vertical dimension of occlusion established initially for the edentulous patients when compared with the measurements made for dentulous patients. The results showed the vertical dimension of occlusion span a range between 106,7 - 138 mm (X _ =122,24) in subjects with natural teeth. In edentulous patients the values of vertical dimension of occlusion span ranged between 109,8 - 141,6 mm (X _ =122,46). The vertical dimension of occlusion in male participans was increased in the group of persons with natural teeth as well as in edentulous patients. The results of t-test proved that there were no statistically significant differences in examined variables between persons with natural teeth and edentulous patients (p>0,01).


2017 ◽  
Vol 29 (2) ◽  
Author(s):  
Nur Emalina Akhma ◽  
Taufik Sumarsongko ◽  
Rasmi Rikmasari

Introduction: Among the most complex restorative challenges for a dentist is that related to determine the occlusal vertical dimension (OVD). Objective methods of determining the OVD offers significant advantages because no radiographs or other special measuring devices are required. Previous review said that the OVD is similar to the pupil-rima oris distance among the population of India. The purpose of this study was to compare whether there was differences between the OVD and the pupil-rima oris distance among Sundanese population. Method: This study was an analytical cross sectional approach. A total of fifty Sundanese students of Faculty of Dentistry, Universitas Padjadjaran who have fulfilled all criteria were chosen randomly to be measured the OVD and the pupil-rima oris distance. Result: Results showed that there was no significant difference between the OVD and the pupil-rima oris distance (α=5%). There were strong correlations between the OVD and the pupil-rima oris distance (p<0.05). An analysed with Spearman’s rank correlation statistic (α=5%) reveals that there was a significant difference between males and females in the OVD and the pupil-rima oris distance. Conclusion: Based on the analysed data, we can conclude that there wass no significant difference between the OVD and the pupil-rima oris distance, thus, the pupil-rima oris distance can be suggested as an objective method to determine the length of OVD in Sundanese population.


2020 ◽  
Vol 13 (1) ◽  
pp. 69-74
Author(s):  
Prawesty Diah Utami ◽  
Herin Setianingsih

Background:Malaria cases have consistently increased and the number of deaths remains largely unchanged.Malaria associated renal injury has a high level of morbidity and mortality. High level of blood urea nitrogen / BUN and plasma creatinine is one of the major factors associated with mortality in humans infected with malaria, indicating that impairment of renal function. HBO is widely used as an adjunctive therapy for many diseases, it is known that HBO hasan action as antiplasmodium, antiinflammation and antioxidant effects. Objective: The aim of this study was to determine the effect of HBO on BUN and creatinine levels in rats infected with P. berghei ANKA. Methods:This research was conducted experimentally post-test only control group on six groups of rats. The samples used were 24 male Rattus norvegicus wistar strain that have been infected by Plasmodium bergheiANKA and divided into 6 groups. Group 1 was given combination artesunate and 1, 5 ATA HBO, grup 2 was given combination artesunate and 3, 0 ATA HBO, group 3 was given 1, 5 ATA HBO, group 4 was given 3, 0 ATA HBO, group 5 was given artesunate and group 6 was given aquadest. HBO therapy is carried out for 10 days and the observation of the levels of BUN and creatinine in mice after treatment on tenth day. Results:Descriptive analysis and statistical analysis (Kruskal wallis snd Mann whitney U posthoc) showed a significant difference (p < α = 0.05) on mean levels of BUN and creatinine group receiving combination of artesunate and HBO 3,0 ATA compared to other groups.Hyperbaric oxygen has the effect of reducing the levels of BUN and creatinine in rats infected by P.berghei ANKA.


Author(s):  
Mine ARGALI DENIZ ◽  
Hilal ER ULUBABA ◽  
M. Furkan ARPACI ◽  
Fatih CAVUS ◽  
Gokhan DEMIRTAS ◽  
...  

Objective: In this study, the effect of tracheal diverticula (TD) on chest anthropometry and its relation with chronic obstructive pulmonary disease (COPD) was evaluated. Method: Between January 2019 and March 2020, 995 patients who underwent chest CT were retrospectively analyzed and TD was detected in 31 cases. Group 1 is only TD, Group 2 is TD + COPD, Group 3 is only COPD, Group 4 is defined as control group. We measured the localization, size, the distance to carina and vocal cord of TDs. In all groups chest diameters at T4 and T9 levels were measured as transverse and vertical plans. Results: TDs detected mostly at the T2 and T3 levels. In Group 1 and Group 2, there was a statistically significant difference the distance to TD of vocal chords. A statistically significant difference was found between Group 1 and Group 3 only in the vertical diameter at the T4 and T9 levels. Conclusion: We observed that COPD effect TD location and also TD had opposite effect on anteroposteriorly increasing chest parameters in COPD. Precence of TD is essential on COPD patients about thorax anthropometry. Keywords: Tracheal diverticulum; antropometry; radiology; COPD; chest diameter


Sign in / Sign up

Export Citation Format

Share Document