scholarly journals CREEP RESISTANCE OF FERRITIC-MARTENSITIC STEEL 16Cr12MoWSiVNbB (EP-823)

2019 ◽  
Vol 62 (4) ◽  
pp. 290-302
Author(s):  
M. Yu. Belomyttsev ◽  
V. G. Molyarov
Keyword(s):  
Ultimate Strength ◽  
Creep Resistance ◽  
Rupture Strength ◽  
Tensile Tests ◽  
Basic Material ◽  
Compression Tests ◽  
Creep Tests ◽  
Delta Ferrite ◽  
Definition Of ◽  
Creep Velocity

Base characteristics of ferritic-martensitic heat resisting steels with 12 % of chrome are parameters of their strength and creep resistance at temperatures of 600 – 750 °С. Steel 16Cr12MoWSiVNbB (EP-823) is considered as the basic material for manufacturing environments fuel rods (TVEL) of a developed reactor with natural safety of BRESTtype. In the literature, there are data about its mechanical characteristics for tensile tests in a range of temperatures of 20 – 750 °С and the limited characteristics of rupture strength. Data on its creep velocity is absent. Laws of creep of steel EP-823 were investigated on metal of three heats with weight of 3 kg. The compression tests at air were applied for cylindrical samples of 5 ÷ 6 mmat temperatures of 600 – 760 °С and stresses of 70 – 310 MPa. The base of compression tests did not exceed 11 hours. The structure after quenching and tempering consisted of tempered martensite and 6 – 12 vol. % of delta-ferrite, the grain size was less 20 μm. It is shown, that the description of creep tests results in double logarithmic (log (σ) – log (έ)) coordinates provides the best concurrence of results of approximation and experiment, than in half-logarithmic (σ – log (έ)). The analysis of parametrical dependences on Hollomon’s PS = (T/1000)[CS – log (έ) and to Larsen-Miller’s PE = (T/1000)[СE – log (σ)] has allowed to find the equations for creep velocity for the set pressure level of 100 – 220 MPa in the form of log (έ) = –19,355 + 9,17 (T/1000) log (σ) and ultimate strength of creep under the set admissions for creep velocity of 0,01 – 1 %/hour in the form of log (σ) = 4,304 – – 0,109 (T/1000) [20 – log (έ)]. Calculations of ultimate strength of creep and creep velocity on pair models and models of Hollomon (Larsen-Miller) give close results, but the preference should be given the second ones as these models consider all three varied factors. Data of control tests under the scheme of a tensile in the same conditions are cited. It is shown, that between results of tests on compression and on tensile at definition of durability characteristics, there is the linear dependence expressed by the equation σ0.2 at compression = 1.3σ0.2 at tensile. At the analysis of creep it has been established, that creep velocity for steel of one grade (09Cr12W3NbB) and for one heat at different type of loading (tensile or compression) have similar values while creep velocities for steel of one grade (EP-823), but of different heats even at one type of loading – compression, can differ substantially.

scholarly journals Thermomechanical Characterization of Monolithic Refractory Castables

2010 ◽  
Vol 70 ◽  
pp. 37-46 ◽  
Author(s):  
Thierry Cutard ◽  
Nicolas Donval ◽  
Aurélien Mazzoni ◽  
Claire Michel ◽  
Fabien Nazaret
Keyword(s):  
Tensile Tests ◽  
Thermomechanical Behavior ◽  
Mechanical Tests ◽  
Image Correlation ◽  
Compression Tests ◽  
Creep Tests ◽  
Refractory Castables ◽  
Complex Shapes ◽  
Damage Processes

This paper deals with the characterization of the thermomechanical behavior of monolithic refractory castables in a wide temperature range, up to 1200°C. Different test types are considered: tensile tests, compression tests, bending tests and tests on more complex shapes and geometries. A particular attention is paid to the detailed characterization and interpretation of the non-linear behaviors of these materials. Monotonic, cyclic and creep tests are considered. In some cases, digital image correlation (DIC) methods can be coupled to mechanical tests to obtain strain fields. Such results are particularly interesting to observe and to understand damage processes. As damage is a major characteristic of the monolithic castable behaviors, links are established between the thermomechanical behavior and damage mechanisms. Two main scales are taken into account for damage characterization: the macroscopic and the microscopic ones. Main mechanisms that are considered deal with microcracking, macrocracking, debonding and cavitation. Two types of materials are considered: non-reinforced and fiber reinforced refractory castables.

scholarly journals Effect of Plasma Nitriding on the Creep and Tensile Properties of the Ti-6Al-4V Alloy

Metals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 618 ◽  
Author(s):  
Gisele Almeida ◽  
Antônio Couto ◽  
Danieli Reis ◽  
Marcos Massi ◽  
Argemiro da Silva Sobrinho ◽  
...  
Keyword(s):  
Creep Resistance ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Tensile Tests ◽  
Secondary Creep ◽  
Creep Tests ◽  
Temperature Range ◽  
Gas Atmosphere ◽  
Creep Time ◽  
Increased Strength

This work aimed to enhance the creep resistance of Ti-6Al-4V alloy treated by plasma nitriding. The nitriding was performed on specimens with a Widmanstätten microstructure for four hours at 690 °C under a gas atmosphere containing Ar:N2:H2 (0.455:0.455:0.090). X-ray diffraction analysis showed that the ε-Ti2N and δ-TiN formed on the nitrided sample, in addition to the α-Ti and β-Ti matrix phases. The layer thickness of this sample was about 1 µm. Hot tensile tests were performed in the temperature range of 500 to 700 °C on nitrided and non-nitrided samples, which indicated an increased strength of the nitrided samples. The same temperature range was used for the creep tests in a stress range of 125 to 319 MPa. The plasma-nitrided samples exhibited better creep resistance when compared to the untreated samples. This result was demonstrated by the decreased secondary creep rate and the increased final creep time. This improvement in the creep resistance appeared to be associated with the formation of the nitrided layer, which worked as a barrier to oxygen diffusion into the material and due to the formation of a surface residual compressive stress.

scholarly journals The microstructure and creep properties of as-cast Mg-Sn-Si-(Al) magnesium alloys

2020 ◽  
Vol 20 (3) ◽  
Author(s):  
Tomasz Rzychoń
Keyword(s):  
Electron Microscopy ◽  
Rare Earth ◽  
Ambient Temperature ◽  
Tensile Properties ◽  
Magnesium Alloys ◽  
Creep Resistance ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Creep Tests ◽  
Creep Properties

Abstract Magnesium alloys containing rare earth metals exhibit good creep resistance up to 300 °C and good tensile properties at ambient temperature. The high cost of rare earth has led to studies regarding the creep resistance of Mg alloys with cheap alloying elements (Sn, Ca, Si) that could be substituted for Mg-RE alloys. In this paper, the influence of Si and Al on microstructure and mechanical properties of Mg-7Sn alloy was investigated using optical (LM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction analysis (XRD), tensile tests and creep tests at 200–250 °C. Microstructure of as-cast alloys consists of α-Mg matrix and intermetallic compounds at the interdendritic regions. Heat treatment consisting of solid solution treatment and ageing increases the tensile properties at ambient temperature due to the precipitation of the fine Mg2Sn phase. The creep resistance of aged Mg-7Sn alloy is poor. The addition of Si and Al to Mg-7Sn alloy has resulted in improving the creep resistance due to the refinement of Mg2Sn phase and the appearance of Mg2Si phase at the grain boundaries. The Mg-7Sn-1Si alloy exhibits better creep resistance at 200 °C than Mg-7Sn-5Si and Mg-7Sn-5Si-2Al alloys. The Mg-7Sn alloys with 5% Si have better creep properties at 250 °C in comparison to Mg-7Sn-1Si alloy.

Regularities and properties of instrumented indentation diagrams obtained by ball-shaped indenter

2020 ◽  
Vol 86 (5) ◽  
pp. 43-51
Author(s):  
V. M. Matyunin ◽  
A. Yu. Marchenkov ◽  
N. Abusaif ◽  
P. V. Volkov ◽  
D. A. Zhgut
Keyword(s):  
Yield Strength ◽  
Ultimate Strength ◽  
Elastoplastic Deformation ◽  
Elastic Limit ◽  
Tensile Tests ◽  
Indentation Load ◽  
International Standards ◽  
Instrumented Indentation ◽  
Indentation Methods ◽  
Special Points

The history of appearance and the current state of instrumented indentation are briefly described. It is noted that the materials instrumented indentation methods using a pyramid and ball indenters are actively developing and are currently regulated by several Russian and international standards. These standards provide formulas for calculating the Young’s modulus and hardness at maximum indentation load. Instrumented indentation diagrams «load F – displacement α» of a ball indenter for metallic materials were investigated. The special points on the instrumented indentation diagrams «F – α» loading curves in the area of elastic into elastoplastic deformation transition, and in the area of stable elastoplastic deformation are revealed. A loading curve area with the load above which the dF/dα begins to decrease is analyzed. A technique is proposed for converting «F – α» diagrams to «unrestored Brinell hardness HBt – relative unrestored indent depth t/R» diagrams. The elastic and elastoplastic areas of «HBt – t/R» diagrams are described by equations obtained analytically and experimentally. The materials strain hardening parameters during ball indentation in the area of elastoplastic and plastic deformation are proposed. The similarity of «HBt – t/R» indentation diagram with the «stress σ – strain δ» tensile diagrams containing common zones and points is shown. Methods have been developed for determining hardness at the elastic limit, hardness at the yield strength, and hardness at the ultimate strength by instrumented indentation with the equations for their calculation. Experiments on structural materials with different mechanical properties were carried out by instrumented indentation. The values of hardness at the elastic limit, hardness at the yield strength and hardness at the ultimate strength are determined. It is concluded that the correlations between the elastic limit and hardness at the elastic limit, yield strength and hardness at the yield strength, ultimate tensile strength and hardness at the ultimate strength is more justified, since the listed mechanical characteristics are determined by the common special points of indentation diagrams and tensile tests diagrams.

scholarly journals Design and characterization of concrete masonry parts and structural concrete using repurposed plastics as aggregate

2019 ◽  
Vol 28 (1) ◽  
pp. 81-88
Author(s):  
Miguel A. González-Montijo ◽  
Hildélix Soto-Toro ◽  
Cristian Rivera-Pérez ◽  
Silvia Esteves-Klomsingh ◽  
Oscar Marcelo Suárez
Keyword(s):  
Structural Strength ◽  
Construction Materials ◽  
Tensile Tests ◽  
Compression Tests ◽  
Conventional Concrete ◽  
Structural Capacity ◽  
Plastic Type ◽  
Concrete Mix ◽  
Scientists And Engineers

AbstractHistorically known for being one of the major pollutants in the world, the construction industry, always in constant advancement and development, is currently evolving towards more environmentally friendly technologies and methods. Scientists and engineers seek to develop and implement green alternatives to conventional construction materials. One of these alternatives is to introduce an abundant, hard to recycle, material that could serve as a partial aggregate replacement in masonry bricks or even in a more conventional concrete mixture. The present work studied the use of 3 different types of repurposed plastics with different constitutions and particle size distribution. Accordingly, several brick and concrete mix designs were developed to determine the practicality of using these plastics as partial aggregate replacements. After establishing proper working material ratios for each brick and concrete mix, compression tests as well as tensile tests for the concrete mixes helped determine the structural capacity of both applications. Presented results proved that structural strength can indeed be reached in a masonry unit, using up to a 43% in volume of plastic. Furthermore, a workable structural strength for concrete can be achieved at fourteen days of curing, using up to a 50% aggregate replacement. A straightforward cost assessment for brick production was produced as well as various empirical observations and recommendations concerning the feasibility of each repurposed plastic type examined.

Creep Properties and Interfacial Microstructure of SiC Whisker Reinforced Si3N4

1989 ◽  
Vol 170 ◽  
Author(s):  
Håkan A. Swan ◽  
Colette O'meara
Keyword(s):  
High Temperature ◽  
Creep Resistance ◽  
Interfacial Microstructure ◽  
Deformation Mechanisms ◽  
Amorphous Films ◽  
Creep Tests ◽  
Creep Properties ◽  
High Temperature Exposure ◽  
Temperature Exposure

AbstractPreliminary creep tests were performed on SiC whisker reinforced and matrix Si3N4 material fabricated by the NPS technique. The material was extensively crystallised in the as received material, leaving only thin amorphous films surrounding the grains. No improvement in the creep resistance could be detected for the whisker reinforced material. The deformation mechanisms were found to be that of cavitation in the form of microcracks, predominantly at the whisker/matrix interfaces, and the formation of larger cracks. Extensive oxidation of the samples, as a result of high temperature exposure to air, was observed for the materials tested at 1375°C.

Effect of Equal-Channel Angular Pressing (ECAP) on Creep in Aluminium Alloys

2007 ◽  
Vol 539-543 ◽  
pp. 2904-2909 ◽  
Author(s):  
Vàclav Sklenička ◽  
Jiří Dvořák ◽  
Marie Kvapilová ◽  
Milan Svoboda ◽  
Petr Král ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
Creep Resistance ◽  
Room Temperature ◽  
Creep Behaviour ◽  
Coarse Grained ◽  
Pure Aluminium ◽  
Creep Tests ◽  
Angular Pressing ◽  
Compression Creep

This paper examines the effect of equal-channel angular pressing (ECAP) on creep behaviour of pure aluminium, binary Al-0.2wt.%Sc alloy and ternary Al-3wt.%Mg-0.2wt.%Sc alloy. The ECAP was conducted at room temperature with a die that had a 90° angle between the channels and 8 repetitive ECAP passes followed route BC. Constant stress compression creep tests were performed at 473 K and stresses ranging between 16 to 80 MPa on ECAP materials and, for comparison purposes, on the initial coarse-grained materials. The results showed that the creep resistance of the ECAP processed Al-Sc and Al-Mg-Sc alloys was markedly deteriorated with respect to unpressed coarse-grained materials.

Heat Treatments Effect on the Mechanical Properties of Industrial Drawn Copper Wires

2013 ◽  
Vol 811 ◽  
pp. 9-13 ◽  
Author(s):  
Zakaria Boumerzoug ◽  
Zakaria Boumerzoug ◽  
Vincent Ji
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Treatment Time ◽  
Void Formation ◽  
Tensile Tests ◽  
Heat Treatments ◽  
Ambient Atmosphere ◽  
Creep Tests ◽  
Prior Heat Treatment ◽  
Industrial Material

In this present investigation, the mechanical properties of industrial drawn copper wires have been studied by creep tests, tensile tests and hardness Vickers. The effect of prior heat treatments at 500°C for different time on the drawn wires behavior was the main goal of this investigation. We have found that these heat treatments influenced the creep behavior of drawn wires and recorded shape curves. The creep tests were applied under ambient atmosphere at 240 °C. The creep duration before rupture decreased with the prior heat treatment time. The creep tests results were confirmed by tensile tests. A relationship between the hardness and the ultimate tensile strength of this industrial material has been established. Optical and scanning electron microscopy observations have been also used. Cross section observations of the wire after tensile or creep-rupture tests have shown that the mechanism of rupture was mainly controlled by the void formation.

scholarly journals Creep Behaviour and Microstructural Characterization of VAT 36 and VAT 32 Superalloys

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 877 ◽  
Author(s):  
Vagner Gobbi ◽  
Silvio Gobbi ◽  
Danieli Reis ◽  
Jorge Ferreira ◽  
José Araújo ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Creep Resistance ◽  
High Performance ◽  
Creep Behaviour ◽  
Ductile Failure ◽  
Microstructural Characterization ◽  
Dislocation Slip ◽  
Creep Tests ◽  
Experimental Conditions ◽  
Wide Range

Superalloys are used primarily for the aerospace, automotive, and petrochemical industries. These applications require materials with high creep resistance. In this work, evaluation of creep resistance and microstructural characterization were carried out at two new nickel intermediate content alloys for application in aerospace industry and in high performance valves for automotive applications (alloys VAT 32 and VAT 36). The alloys are based on a high nickel chromium austenitic matrix with dispersion of intermetallic L12 and phases containing different (Nb,Ti)C carbides. Creep tests were performed at constant load, in the temperature range of 675–750 °C and stress range of 500–600 MPa. Microstructural characterization and failure analysis of fractured surfaces of crept samples were carried out with optical and scanning electron microscopy with EDS. Phases were identified by Rietveld refinement. The results showed that the superalloy VAT 32 has higher creep resistance than the VAT 36. The superior creep resistance of the alloy VAT 32 is related to its higher fraction of carbides (Nb,Ti)C and intermetallic L12 provided by the amount of carbon, titanium, and niobium in its chemical composition and subsequent heat treatment. During creep deformation these precipitates produce anchoring effect of grain boundaries, hindering relative slide between grains and therefore inhibiting crack formation. These volume defects act also as obstacles to dislocation slip and climb, decreasing the creep rate. Failure analysis of surface fractures of crept samples showed intergranular failure mechanism at crack origin for both alloys VAT 36 and VAT 32. Intergranular fracture involves nucleation, growth, and subsequent binding of voids. The final fractured portion showed transgranular ductile failure, with dimples of different shapes, generated by the formation and coalescence of microcavities with dissimilar shape and sizes. The occurrence of a given creep mechanism depends on the test conditions. At creep tests of VAT 32 and VAT 36, for lower stresses and higher temperature, possible dislocation climb over carbides and precipitates would prevail. For higher stresses and intermediate temperatures shear mechanisms involving stacking faults presumably occur over a wide range of experimental conditions.

Microstructure and Creep Properties of Selected Gravity Casting Magnesium Alloys

2016 ◽  
Vol 682 ◽  
pp. 372-379
Author(s):  
Tomasz Rzychoń
Keyword(s):  
Magnesium Alloys ◽  
Creep Resistance ◽  
Low Cost ◽  
Xrd Analysis ◽  
Phase Identification ◽  
Creep Tests ◽  
Gravity Casting ◽  
Creep Properties ◽  
Transmission Electron ◽  
Primary Crystals

In this paper microstructure and creep properties of Mg-Al-Ca-Sr, Mg-Zn-RE-Zr and Mg-Sn-Si gravity casting magnesium alloys are presented. The microstructure was characterized using light microscopy, scanning and transmission electron microscopy. Phase identification was made by SAED and XRD analysis. Creep tests were carried out in the temperature range from 180°C to 200°C at applied stress of 60 MPa. Microstructure of Mg-Al-Ca-Sr alloys composed of α-Mg grains and C36, C15 and C14 intermetallic compounds in the interdendritic regions. In case of Mg-Zn-RE-Zr alloys the dominant intermetallic compound is (Mg,Zn)12RE phase also located in the interdendritic regions. Microstructure of Mg-Sn-Si alloys after T6 heat treatment consists of plate-like precipitates of Mg2Sn phase, primary crystals of Mg2Si phase and globular Mg2Si phase. Among the alloys in this study, the low-cost Mg-5Al-3Ca-0.7Sr alloy has the best creep resistance. The other alloys, excluding the Mg-5Si-7Sn alloy, are characterized by a poorer creep resistance in compared to Mg-5Al-3Ca-0.7Sr alloy, however their creep resistance is better if compared to typical Mg-Al alloys. Creep resistance of Mg-5Si-7Sn alloy is very low.

Sign in / Sign up

Export Citation Format

Share Document