scholarly journals The Effect of Heat Treatment on the Mechanical Properties of SAE 1035 Steel

2016 ◽  
Vol 8 ◽  
pp. 32-43
Author(s):  
Osita Obiukwu ◽  
Henry Udeani ◽  
Progress Ubani
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Fatigue Strength ◽  
Carbon Steel ◽  
Endurance Limit ◽  
Tensile Tests ◽  
Treatment Processes ◽  
Treatment Conditions ◽  
Hardness Tests ◽  
Heat Treated

The effect of various heat treatment operations (annealing, normalizing, tempering) on mechanical properties of 0.35% carbon steel was investigated. The change in the value of endurance limit of the material as a result of the various heat-treatment operations were studied thoroughly. It was found that the specimens tempered at low temperature (200°C) exhibited the best fatigue strength. Microscope was used to characterize the structural properties resulting from different heat treatment processes. The results from the tensile tests impact tests and hardness tests showed that the mechanical properties variate at every heat-treatment conditions. The microstructure of differently heat-treated steels was also studied.

Effect of Two-Cycle Heat Treatment on Mechanical Properties of Ductile Iron

2013 ◽  
Vol 393 ◽  
pp. 79-82
Author(s):  
B. Abdullah ◽  
Mohd Faizul Idham ◽  
A. Jaffar ◽  
Ahmad Faiz Zubair ◽  
M. Mohamed
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Ductile Iron ◽  
Treatment Process ◽  
Treatment Processes ◽  
Hardness Tests ◽  
Heat Treated ◽  
Different Temperatures ◽  
Two Stages ◽  
Holding Temperature

The aim of this study is to investigate the mechanical properties of ductile iron after treatment with two-cycle heat treatment processes which modified from austempering. The modified heat treatments have two stages holding temperature. Ductile iron was austenitized at 900 °C for an hour and followed by transferring the sample to other furnace which was set at different temperatures of i) 250 °C; ii) 300 °C; iii) 350 °C without quenching for 1.5 hours. Tensile (ASTM E8M), impact (ASTM-E23-1990) and Rockwell hardness tests were carried out to study the mechanical properties of the ductile iron. It was found that the sample which was heat treated using two-cycle heat treatment process at temperature of 250 °C contributed to better absorbing impact energy properties and hardness properties. Meanwhile, sample that heat treated at 350 °C has higher tensile strength.

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

Mechanical Behavior of Friction Stir Welded AA-6061 Thick Plates in Different Heat Treatment Conditions

2021 ◽  
Vol 875 ◽  
pp. 203-210
Author(s):  
Talha Ahmed ◽  
Wali Muhammad ◽  
Zaheer Mushtaq ◽  
Mustasim Billah Bhatty ◽  
Hamid Zaigham
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Treatment ◽  
Travel Speed ◽  
Butt Joint ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Joint Form

In this study, mechanical properties of friction stir welded Aluminum Alloy (AA) 6061 in three different heat treatment conditions i.e. Annealed (O), Artificially aged (T6) and Post Weld Heat Treated (PWHT) were compared. Plates were welded in a butt joint form. Parameters were optimized and joints were fabricated using tool rotational speed and travel speed of 500 rpm and 350 mm/min respectively. Two sets of plates were welded in O condition and out of which one was, later, subjected to post weld artificial aging treatment. Third set was welded in T6 condition. The welds were characterized by macro and microstructure analysis, microhardness measurement and mechanical testing. SEM fractography of the tensile fracture surfaces was also performed. Comparatively better mechanical properties were achieved in the plate with PWHT condition.

scholarly journals Comparison of Different Heat Treatment Processes of Selective Laser Melted 316L Steel Based on Analysis of Mechanical Properties

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3805 ◽  
Author(s):  
Janusz Kluczyński ◽  
Lucjan Śnieżek ◽  
Krzysztof Grzelak ◽  
Artur Oziębło ◽  
Krzysztof Perkowski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Hot Isostatic Pressing ◽  
Tensile Tests ◽  
Fracture Analysis ◽  
Image Correlation ◽  
Treatment Processes ◽  
Different Types ◽  
316L Steel ◽  
Precipitation Heat

In this study, we analyzed the mechanical properties of selectively laser melted (SLM) steel obtained via different modifications during and after the manufacturing process. The aim was to determine the effects of precipitation heat treatment on the mechanical properties of elements additively manufactured using three different process parameters. Some samples were additionally obtained using hot isostatic pressing (HIP), while some were treated using two different types of heat treatment and a combination of those two processes. From each manufactured sample, a part of the material was taken for structural analysis including residual stress analysis and microstructural investigations. In the second part of the research, the mechanical properties were studied to define the scleronomic hardness of the samples. Finally, tensile tests were conducted using a digital image correlation (DIC) test and fracture analysis. The treated samples were found to be significantly elongated, thus indicating the advantages of using precipitation heat treatment. Additionally, precipitation heat treatment was found to increase the porosity of samples, which was the opposite compared to HIP-treated samples.

scholarly journals Heat-Treated Wood as a Substrate for Coatings, Weathering of Heat-Treated Wood, and Coating Performance on Heat-Treated Wood

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Vlatka Jirouš-Rajković ◽  
Josip Miklečić
Keyword(s):  
Heat Treatment ◽  
Wood Species ◽  
Treated Wood ◽  
Wood Properties ◽  
Treatment Method ◽  
Coating Performance ◽  
Treatment Processes ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Trade Names

Heat treatment is a method of wood modification with increasing market acceptance in Europe. The major patented European commercial heat treatment processes have trade names ThermoWood, Platowood, Retiwood, Le Bois Perdure, and Oil-Heat-Treated Wood (OHT). To what extent modification of wood affects the resistance of wood to weathering is also an important aspect for wood applications, especially where appearance is important. Unfortunately, heat-treated wood has poor resistance to weathering, and surface treatment with coatings is required for both protection and aesthetic reasons. As a substrate for coating, heat-treated wood has altered characteristics such as lower hygroscopicity and liquid water uptake and changed acidity, wettability, surface free energy, and anatomical microstructure. Various wood species, heat treatment method, treatment intensity, and treatment conditions exhibited a different extent of changes in wood properties. These altered properties could affect coating performance on heat-treated wood. The reported changes in acidity and in surface energy due to heat treatments are inconsistent with one another depending on wood species and temperature of the treatments. This paper gives an overview of the research results with regards to properties of heat-treated wood that can affect coating performance and weathering of uncoated and coated heat-treated wood.

Mechanical properties of heat-treated cellulose nanofiber-reinforced polyvinyl alcohol nanocomposite

2016 ◽  
Vol 51 (14) ◽  
pp. 1971-1977 ◽  
Author(s):  
NH Noor Mohamed ◽  
Hitoshi Takagi ◽  
Antonio N Nakagaito
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Tensile Tests ◽  
Cellulose Nanofiber ◽  
Heat Treated ◽  
Scanning Electron ◽  
Polyvinyl Alcohol Films

The mechanical properties of cellulose nanofiber-reinforced polyvinyl alcohol composite were studied. Neat polyvinyl alcohol films, cellulose nanofiber sheets, and their nanocomposites containing cellulose nanofiber weight ratios of 5, 15, 30, 40, 45, 50 and 80 wt% were fabricated. Heat treatment by hot pressing at 180℃ was conducted on the specimens to study its effect to the mechanical properties and the results were compared with the non heat-treated specimens. Morphology of the composites was studied by scanning electron microscopy and the mechanical properties were evaluated by means of tensile tests. The results showed that increase of cellulose nanofiber content from 5 wt% to 80 wt% has increased the tensile strength of the composites up to 180 MPa, with cellulose nanofiber content higher than 40 wt% yielding higher tensile strength. The heat-treated specimens exhibited higher tensile strength compared to those of untreated specimens.

Microstructure and Properties of Heat-Treated 440C Martensitic Stainless Steel

2013 ◽  
Vol 334-335 ◽  
pp. 105-110 ◽  
Author(s):  
Siti Hawa Mohamed Salleh ◽  
Mohd Nazree Derman ◽  
Mohd Zaidi Omar ◽  
Junaidi Syarif ◽  
S. Abdullah
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Stainless Steel ◽  
Martensitic Stainless Steel ◽  
Ferrite Matrix ◽  
Rapid Quenching ◽  
Heat Treated Sample ◽  
Treatment Processes ◽  
Heat Treated ◽  
Treated Sample

440C martensitic stainless steels are widely used because of their good mechanical properties. The mechanical properties of 440C martensitic stainless steel were evaluated after heat treatment of these materials at various types of heat treatment processes. The initial part of this investigation focused on the microstructures of these 440C steels. Microstructure evaluations from the as-received to the as-tempered condition were described. In the as-received condition, the formations of ferrite matrix and carbide particles were observed in this steel. In contrast, the precipitation of M7C3carbides and martensitic structures were present in this steel due to the rapid quenching process from the high temperature condition. After precipitation heat treatment, the Cr-rich M23C6carbides were identified within the structures. Moreover, a 30 minutes heat-treated sample shows the highest value of hardness compared to the others holding time. Finally, the tempering process had been carried out to complete the whole heat treatment process in addition to construct the secondary hardening phenomenon. It is believed that this phenomenon influenced the value of hardness of the 440C steel.

scholarly journals The Effect of Cooling Rate on Mechanical Properties of Carbon Steel (St 35)

2014 ◽  
Vol 7 (1) ◽  
pp. 109-118
Author(s):  
Jenan Mohammed Nagie
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Carbon Steel ◽  
Cooling Rate ◽  
Experimental Results ◽  
Heat Treated ◽  
Before And After ◽  
Water Media ◽  
The Relationship

This paper is aimed to study the effect of cooling rate on mechanical properties of Steel 35. Specimens prepared to apply tensile, torsion, impact and hardness tests.Many prepared specimens heat treated at (850ºC) for one hour and subsequently were cooled by three different media [Water-Air-furnace] to show the effect of Medias cooling rate on mechanical properties. Microstructures of all specimens examined before and after heat treatment by an optical microscopy.To figure the phases obtained after heat treatment and its effect on the mechanical properties Experimental results have shown that the microstructure of steel can be changed and significantly improved by varying line cooling rate thus, improving one property will effect on the others because of the relationship between all properties.In water media tensile, torsion and hardness improved while impact results reduced. Air media contributed in improving most of the mechanical properties because of grain size homogeneity. At furnace media ductility and impact improved

STUDY OF THE STRUCTURE, PHASE COMPOSITION, PHYSICOMECHANICAL PROPERTIES, AND ALSO OPTIMIZATION OF HEAT TREATMENT PROCESSES OF CAST HEAT-RESISTANT NICKEL ALLOY ЕР202 BY THE METHOD OF MATHEMATICAL MODELING

2021 ◽  
pp. 3-10
Author(s):  
V. N. Gadalov ◽  
V. R. Petrenko ◽  
E. A. Filatov ◽  
I. V. Vornacheva ◽  
A. V. Filonovich
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
General Information ◽  
Regression Equations ◽  
Two Stage ◽  
Heat Resistant ◽  
Treatment Processes ◽  
Nickel Chromium ◽  
Treatment Conditions

General information about the EP202 heat-resistant weldable alloy with a nickel-chromium matrix is given. Its chemical composition, manufacturing technology, recommended heat treatment modes for short-term and long-term parts, as well as recommended maintenance modes for castings and rodsheets are presented. A description of the structure and phase composition of the alloy in the cast state and after heat treatment is given. The mechanical properties of the alloy depending on the test temperature and heat treatment conditions for longitudinal and transverse specimens are given. The physical properties of the alloy at various temperatures are also described. Further, the study presents the study of the modes of stepwise aging on the structure and mechanical properties of the EP202 alloy. An increase in mechanical properties after two-stage aging in comparison with the initial heat treatment due to a more uniform distribution of the strengthening γ¢-phase over the volume of the alloy was established. With the help of the obtained regression equations, the optimal temperature of the first stage of two-stage aging (540 C) was established, which ensures an increase in the level of impact strength by (20...25) %.

Investigation of the joinability of the high-strength aluminum alloy AA7075 in shear-clinching processes

2021 ◽  
pp. 146442072110679
Author(s):  
S Wiesenmayer ◽  
M Merklein
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
High Strength Aluminum Alloy ◽  
Heat Treated ◽  
Strength Alloy ◽  
Heating Up

Shear-clinching has proven to be a suitable technology for joining of high-strength materials. However, the mechanical properties of the upper joining partner are limited due to the high strains, which occur during the process. Therefore, shear-clinching of the high-strength aluminum alloy AA7075 in the T6 temper is not possible. Yet, the mechanical properties of hardenable alloys of the 7000 series can be influenced by a heat treatment. Thus, within the scope of this work, the joinability of the high-strength alloy AA7075 in shear-clinching processes in dependance of its temper is investigated. The as fabricated state F, the artificially aged T6 temper, a paint baked state and the naturally aged T4 temper are compared to the fully solution annealed W temper as well as to a retrogression heat-treated state. For retrogression heat treatment, a laser is used as heat source, heating up the alloy for a short term in order to only partially dissolve precipitations. The resulting mechanical properties are determined with uniaxial tensile tests. Moreover, the influence of the mechanical properties of AA7075 on the shear-clinching process, the joint formation and the resulting joint strength is analyzed.

Sign in / Sign up

Export Citation Format

Share Document