scholarly journals Comparative Adsorption of Methylene Blue on Different Low Cost Adsorbents by Continuous Column Process

2018 ◽  
Vol 77 ◽  
pp. 26-34
Author(s):  
Mohammad Abul Hossain ◽  
Md. Mahbbat Ali ◽  
Tajmeri Selima Akhter Islam
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Spectroscopic Method ◽  
Black Tea ◽  
Breakthrough Curves ◽  
Synthetic Wastewater ◽  
Batch Adsorption ◽  
Tea Leaves ◽  
Column Adsorption

Dyes are commonly found in the effluents of many industries. The effectiveness of adsorption for the removal of dye from wastewaters has been made it an ideal alternative to other expensive treatment methods. Continuous column adsorption is more affective than batch adsorption. A comparative column adsorption study was performed using three different low cost adsorbents for the removal of methylene blue from synthetic wastewater. Sand was collected from Cox’s Bazar, and sugarcane bagasse and used black tea leaves were locally prepared in laboratory. Three columns were designed for different adsorbents maintaining all conditions were to be approximately similar. UV-vis spectroscopic method was used for analysis of methylene blue in solution. Column adsorption experiments were performed to investigate the comparison of breakthrough curves and exhaust capacity of three different adsorbents. Column study shows that the adsorption capacity of used black tea leaves is highest. The adsorption capacity of bagasse is lower than tea leaves but higher than sand.

scholarly journals Sheet-like Skeleton Carbon Derived from Shaddock Peels with Hierarchically Porous Structures for Ultra-Fast Removal of Methylene Blue

Water ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 2554
Author(s):  
Panlong Dong ◽  
Hailin Liu ◽  
Shengrui Xu ◽  
Changpo Chen ◽  
Suling Feng ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Adsorption Process ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Hierarchically Porous ◽  
Column Adsorption

To remove the pollutant methylene blue (MB) from water, a sheet-like skeleton carbon derived from shaddock peels (SPACs) was prepared by NaOH activation followed by a calcination procedure under nitrogen protection in this study. Characterization results demonstrated that the as-prepared SPACs displayed a hierarchically porous structure assembled with a thin sheet-like carbon layer, and the surface area of SPAC-8 (activated by 8 g NaOH) was up to 782.2 m2/g. The as-prepared carbon material presented an ultra-fast and efficient adsorption capacity towards MB due to its macro-mesoporous structure, high surface area, and abundant functional groups. SPAC-8 showed ultrafast and efficient removal capacity for MB dye. Adsorption equilibrium was reached within 1 min with a removal efficiency of 99.6% at an initial concentration of 100 mg/g under batch adsorption model conditions. The maximum adsorption capacity for MB was up to 432.5 mg/g. A pseudo-second-order kinetic model and a Langmuir isotherm model described the adsorption process well, which suggested that adsorption rate depended on chemisorption and the adsorption process was controlled by a monolayer adsorption, respectively. Furthermore, column adsorption experiments showed that 96.58% of MB was removed after passing through a SPAC-8 packed column with a flow rate of 20 mL/min, initial concentration of 50 mg/L, and adsorbent dosage of 5 mg. The as-prepared adsorbent displays potential value in practical applications for dye removal due to its ultrafast and efficient adsorption capacity.

Characterization of the Corallina Elongata Alga and Study of its Biosorption Properties for Methylene Blue

2019 ◽  
Vol 41 (1) ◽  
pp. 62-62
Author(s):  
Farida Bouremmad Farida Bouremmad ◽  
Abdennour Bouchair Abdennour Bouchair ◽  
Sorour Semsari Parapari Sorour Semsari Parapari ◽  
Shalima Shawuti and Mehmet Ali Gulgun Shalima Shawuti and Mehmet Ali Gulgun
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Mediterranean Coast ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Aquatic Biomass ◽  
Equilibrium Data

Biosorbents can be an alternative to activated carbon. They are derived from agricultural by-products or aquatic biomass. They are low cost and they may have comparable performances to those of activated carbon. The present study focuses on the characterization of the Corallina Elongata (CE) alga and its adsorption performance for Methylene Blue (MB), this alga is found in abundance at the Mediterranean coast of the city of Jijel in eastern Algeria. The dried alga was characterized using various characterization techniques such as DTA, TG, FTIR, XRD, SEM and EDX, which showed that the material consists essentially of a calcite containing magnesium. Batch adsorption studies were carried out and the effect of experimental parameters Such as pH, initial dye concentration, temperature, adsorbent dose and contact time, on the adsorption of MB was studied. The kinetic experimental data were found to conform to the pseudo-second-order model with good correlation and equilibrium data were best fitted to The Langmuir model, with a maximum adsorption capacity of 34.4 mg/g. The adsorption isotherms at various temperatures allowed the determination of certain thermodynamic parameters (ΔG, ΔH and ΔS). Finally, the adsorption results showed a good affinity between CE and MB with a high adsorption capacity.

THE REMOVAL OF METHYLENE BLUE AND REMAZOL BRILLIANT BLUE R DYES BY USING ORANGE PEEL AND SPENT TEA LEAVES

2015 ◽  
Vol 74 (11) ◽  
Author(s):  
Zainab Mat Lazim ◽  
Elina Mazuin ◽  
Tony Hadibarata ◽  
Zulkifli Yusop
Keyword(s):  
Methylene Blue ◽  
Removal Rate ◽  
Low Cost ◽  
Orange Peel ◽  
Brilliant Blue ◽  
Batch Adsorption ◽  
Tea Leaves ◽  
Remazol Brilliant Blue R ◽  
Spent Tea Leaves ◽  
Dyes Removal

This study explored the low-cost adsorbent of orange peel and spent tea leave for Methylene Blue (MB) and Remazol Brilliant Blue R (RBBR) dyes removal from aqueous solutions. The removal rate and adsorption capacity on the adsorption of dyes were investigated using the batch adsorption study. The present study indicates that the MB was easier to remove by both orange peel and spent tea leave compared to RBBR with percentage removal of 95.72 % and 99.02 % respectively. The effects of morphology, functional groups, and surface area of adsorbents were investigated by using FESEM, FTIR, and BET. The result proved that orange peel and spent tea leave were promising material as an alternative adsorbent for the removal of MB from aqueous solution. 

Garlic Peel as Adsorbent for the Removal of Methylene Blue from Aqueous Solution

2014 ◽  
Vol 694 ◽  
pp. 367-371 ◽  
Author(s):  
Cheng You Ma ◽  
Zhen Li ◽  
Wan He Zhao ◽  
Ying Xu ◽  
Guang Rui Cui ◽  
...  
Keyword(s):  
Waste Water ◽  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Raw Material ◽  
Column Adsorption ◽  
Ph Dependent ◽  
Garlic Peel ◽  
Dyes Removal

A new biosorbent prepared by using garlic peel as the raw material was investigated for the removal of methylene blue (MB) from aqueous solution. Results showed that adsorption of MB on garlic peel gel was highly pH-dependent, and equilibrium was attained in 10 min. The adsorption capacity is 440 mg MB per gram of garlic peel gel. The column adsorption results show that MB can be completely removed from aqueous solution, and 1.0 M HCl is effective to elute the adsorbed MB off the column and condense the initial MB solution to more than 40 times. The prepared garlic gel exhibits as a potential low-cost and effective adsorbent for dyes removal from waste water.

scholarly journals Fly Ash Coated with Magnetic Materials: Improved Adsorbent for Cu (II) Removal from Wastewater

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 63
Author(s):  
Maria Harja ◽  
Gabriela Buema ◽  
Nicoleta Lupu ◽  
Horia Chiriac ◽  
Dumitru Daniel Herea ◽  
...  
Keyword(s):  
Fly Ash ◽  
Adsorption Capacity ◽  
Copper Ions ◽  
Synthetic Wastewater ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Copper Adsorption ◽  
X Ray

Fly ash/magnetite material was used for the adsorption of copper ions from synthetic wastewater. The obtained material was characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) surface area, and vibrating sample magnetometer (VSM). Batch adsorption experiments were employed in order to investigate the effects of adsorbent dose, initial Cu (II) concentration and contact time over adsorption efficiency. The experimental isotherms were modeled using Langmuir (four types of its linearization), Freundlich, Temkin, and Harkins–Jura isotherm models. The fits of the results are estimated according to the Langmuir isotherm, with a maximum adsorption capacity of 17.39 mg/g. The pseudo-second-order model was able to describe kinetic results. The data obtained throughout the study prove that this novel material represents a potential low-cost adsorbent for copper adsorption with improved adsorption capacity and magnetic separation capability compared with raw fly ash.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

Insights into the mechanism of methylene blue removed by novel and classic biochars

2019 ◽  
Vol 79 (8) ◽  
pp. 1561-1570
Author(s):  
Wei Chen ◽  
Fengting Chen ◽  
Bin Ji ◽  
Lin Zhu ◽  
Hongjiao Song
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Low Cost ◽  
Underlying Mechanism ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Average Pore ◽  
Adsorption Effect ◽  
Magnolia Grandiflora

Abstract The adsorption behavior and the underlying mechanism of methylene blue (MB) sorption on biochars prepared from different feedstocks at 500 °C were evaluated. The biochar feedstocks included Magnolia grandiflora Linn. leaves biochar (MBC), pomelo (Citrus grandis) peel biochar (PBC) and badam shell biochar (BBC). The results of characterizing and analyzing the samples showed that different biochars had different effects on the adsorption of MB. It could be found that MBC had the best adsorption effect on MB due to its largest average pore diameter of 5.55 nm determined by Brunauer-Emmett-Teller analysis. Under the optimal conditions, the maximum adsorption capacities of BBC, PBC and MBC were 29.7, 85.15 and 99.3 mg/g, respectively. The results showed that the amount of adsorption was affected by the pH value. The maximum adsorption capacity of MBC was 46.99 mg/g when it was at pH of 3, whereas for the same experimental conditions the maximum adsorption capacity of BBC and PBC was 25.29 mg/g at pH of 11 and 36.08 mg/g at pH of 7, respectively. Therefore, MBC was found to be a most efficient low-cost adsorbentl for dye wastewater treatment compared with BBC and PBC, and it had the best removal effect under acidic conditions.

scholarly journals Compressive Alginate Sponge Derived from Seaweed Biomass Resources for Methylene Blue Removal from Wastewater

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 961 ◽  
Author(s):  
Xiaojun Shen ◽  
Panli Huang ◽  
Fengfeng Li ◽  
Xiluan Wang ◽  
Tongqi Yuan ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Water Treatment ◽  
Low Cost ◽  
Fixed Bed ◽  
Polymer Materials ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Seaweed Biomass ◽  
Biomass Resources ◽  
The Impact

Low cost fabrication of water treatment polymer materials directly from biomass resources is urgently needed in recent days. Herein, a compressive alginate sponge (AS) is prepared from seaweed biomass resources through a green two-step lyophilization method. This material is much different from conventional oven-, air-, vacuum-dried alginate-based adsorbents, which show limitations of shrinkage, rigidness, tight nonporous structure and restricted ions diffusion, hindering its practical applications, and was used to efficiently remove methylene blue (MB), a main colorful contaminant in dye manufacturing, from wastewater. The batch adsorption studies are carried out to determine the impact of pH, contact time and concentration of dye on the adsorption process. The maximum adsorption capacity can be obtained at 1279 mg g−1, and the shape-moldable AS can be facilely utilized as a fixed-bed absorption column, providing an efficient approach for continuous removal of MB within a short time. It is also important that such a compressive AS can be regenerated by a simple squeezing method while retaining about 70% capacity for more than ten cycles, which is convenient to be reused in practical water treatment. Compressive AS demonstrates its merits of high capability, large efficiency and easy to recycle as well as low cost resources, indicating widespread potentials for application in dye contaminant control regarding environmental protection.

scholarly journals Methylene Blue Adsorption from aqueous solution by low cost vine-wood biomass

2021 ◽  
Author(s):  
Rachida Souidi ◽  
yasmina khane ◽  
Lahcen Belarbi ◽  
Smain Bousalem
Keyword(s):  
Methylene Blue ◽  
Sulfuric Acid ◽  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Sulfuric Acid Concentration ◽  
Analytical Techniques ◽  
Batch Adsorption ◽  
Adsorbent Dosage ◽  
Adsorption Desorption

Abstract In this work, the sawdust of vine wood (VW) was treated with sulfuric acid and used to adsorb methylene blue (MB) from aqueous solutions via a batch adsorption process. The characteristics of the adsorbent were determined by various analytical techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) and Brunauer−Emmett−Teller (BET) N2 adsorption−desorption isotherms. The effects of various experimental parameters including sulfuric acid concentration, particle size of the adsorbent, pH of the solution, contact time, initial concentration, adsorbent dosage and temperature on adsorption of MB by activating sawdust were systematically investigated. The experimental results showed that the adsorption efficiency was increased with contact time and adsorbent dosage. The maximum removal efficiency was found after 180 min of solid/liquid contact with adsorbent doses of 1 g/l for sawdust. The isotherm and kinetic experimental data for MB adsorption on VW sawdust were best-fitted by Langmuir models and Pseudo-second-order, respectively. The calculated values of the entropy (ΔS°), enthalpy (ΔH°) and Gibbs energy (ΔG°) indicated that the adsorption process was exothermic in nature. These results suggest that the activated sawdust can be employed as a low-cost and environmentally friendly adsorbent for the treatment of wastewaters containing dyes.

Sign in / Sign up

Export Citation Format

Share Document