scholarly journals Integrating Hardware and Software Filtering in Embedded System Audio Data Processing: An Embedded Systems Course Project

2021 ◽  
Author(s):  
Vincent Winstead
Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1450
Author(s):  
Xiang Wang ◽  
Zhun Zhang ◽  
Qiang Hao ◽  
Dongdong Xu ◽  
Jiqing Wang ◽  
...  

The hardware security of embedded systems is raising more and more concerns in numerous safety-critical applications, such as in the automotive, aerospace, avionic, and railway systems. Embedded systems are gaining popularity in these safety-sensitive sectors with high performance, low power, and great reliability, which are ideal control platforms for executing instruction operation and data processing. However, modern embedded systems are still exposing many potential hardware vulnerabilities to malicious attacks, including software-level and hardware-level attacks; these can cause program execution failure and confidential data leakage. For this reason, this paper presents a novel embedded system by integrating a hardware-assisted security monitoring unit (SMU), for achieving a reinforced system-on-chip (SoC) on ensuring program execution and data processing security. This architecture design was implemented and evaluated on a Xilinx Virtex-5 FPGA development board. Based on the evaluation of the SMU hardware implementation in terms of performance overhead, security capability, and resource consumption, the experimental results indicate that the SMU does not lead to a significant speed degradation to processor while executing different benchmarks, and its average performance overhead reduces to 2.18% on typical 8-KB I/D-Caches. Security capability evaluation confirms the monitoring effectiveness of SMU against both instruction and data tampering attacks. Meanwhile, the SoC satisfies a good balance between high-security and resource overhead.


2020 ◽  
Vol 5 (2) ◽  
pp. 23-28
Author(s):  
Michal Kelemen ◽  
Ľubica Miková ◽  
Darina Hroncová ◽  
Filip Filakovský ◽  
Peter Ján Sinčák

The main role of embedded system is to control the product behaviour or control of outside world. Microcontroller as embedded system obtains information through the sensors and makes adequate impact to outside world after sensor data processing. The microcontroller impact is realized through the actuators which convert the electrical energy (or different type of energy) to mechanical work. These processes are executed because of fulfil customer requirements. Microcontrollers as signal controllers work only with low power signals. This paper discusses the possibilities and application of controlling the power subsystems via using the embedded systems.


10.28945/3391 ◽  
2009 ◽  
Author(s):  
Moshe Pelleh

In our world, where most systems become embedded systems, the approach of designing embedded systems is still frequently similar to the approach of designing organic systems (or not embedded systems). An organic system, like a personal computer or a work station, must be able to run any task submitted to it at any time (with certain constrains depending on the machine). Consequently, it must have a sophisticated general purpose Operating System (OS) to schedule, dispatch, maintain and monitor the tasks and assist them in special cases (particularly communication and synchronization between them and with external devices). These OSs require an overhead on the memory, on the cache and on the run time. Moreover, generally they are task oriented rather than machine oriented; therefore the processor's throughput is penalized. On the other hand, an embedded system, like an Anti-lock Braking System (ABS), executes always the same software application. Frequently it is a small or medium size system, or made up of several such systems. Many small or medium size embedded systems, with limited number of tasks, can be scheduled by our proposed hardware architecture, based on the Motorola 500MHz MPC7410 processor, enhancing its throughput and avoiding the software OS overhead, complexity, maintenance and price. Encouraged by our experimental results, we shall develop a compiler to assist our method. In the meantime we will present here our proposal and the experimental results.


Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 13
Author(s):  
Balaji M ◽  
Chandrasekaran M ◽  
Vaithiyanathan Dhandapani

A Novel Rail-Network Hardware with simulation facilities is presented in this paper. The hardware is designed to facilitate the learning of application-oriented, logical, real-time programming in an embedded system environment. The platform enables the creation of multiple unique programming scenarios with variability in complexity without any hardware changes. Prior experimental hardware comes with static programming facilities that focus the students’ learning on hardware features and programming basics, leaving them ill-equipped to take up practical applications with more real-time constraints. This hardware complements and completes their learning to help them program real-world embedded systems. The hardware uses LEDs to simulate the movement of trains in a network. The network has train stations, intersections and parking slots where the train movements can be controlled by using a 16-bit Renesas RL78/G13 microcontroller. Additionally, simulating facilities are provided to enable the students to navigate the trains by manual controls using switches and indicators. This helps them get an easy understanding of train navigation functions before taking up programming. The students start with simple tasks and gradually progress to more complicated ones with real-time constraints, on their own. During training, students’ learning outcomes are evaluated by obtaining their feedback and conducting a test at the end to measure their knowledge acquisition during the training. Students’ Knowledge Enhancement Index is originated to measure the knowledge acquired by the students. It is observed that 87% of students have successfully enhanced their knowledge undergoing training with this rail-network simulator.


Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1031
Author(s):  
Joseba Gorospe ◽  
Rubén Mulero ◽  
Olatz Arbelaitz ◽  
Javier Muguerza ◽  
Miguel Ángel Antón

Deep learning techniques are being increasingly used in the scientific community as a consequence of the high computational capacity of current systems and the increase in the amount of data available as a result of the digitalisation of society in general and the industrial world in particular. In addition, the immersion of the field of edge computing, which focuses on integrating artificial intelligence as close as possible to the client, makes it possible to implement systems that act in real time without the need to transfer all of the data to centralised servers. The combination of these two concepts can lead to systems with the capacity to make correct decisions and act based on them immediately and in situ. Despite this, the low capacity of embedded systems greatly hinders this integration, so the possibility of being able to integrate them into a wide range of micro-controllers can be a great advantage. This paper contributes with the generation of an environment based on Mbed OS and TensorFlow Lite to be embedded in any general purpose embedded system, allowing the introduction of deep learning architectures. The experiments herein prove that the proposed system is competitive if compared to other commercial systems.


Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 34
Author(s):  
Michele Alessandrini ◽  
Giorgio Biagetti ◽  
Paolo Crippa ◽  
Laura Falaschetti ◽  
Lorenzo Manoni ◽  
...  

Singular value decomposition (SVD) is a central mathematical tool for several emerging applications in embedded systems, such as multiple-input multiple-output (MIMO) systems, data analytics, sparse representation of signals. Since SVD algorithms reduce to solve an eigenvalue problem, that is computationally expensive, both specific hardware solutions and parallel implementations have been proposed to overcome this bottleneck. However, as those solutions require additional hardware resources that are not in general available in embedded systems, optimized algorithms are demanded in this context. The aim of this paper is to present an efficient implementation of the SVD algorithm on ARM Cortex-M. To this end, we proceed to (i) present a comprehensive treatment of the most common algorithms for SVD, providing a fairly complete and deep overview of these algorithms, with a common notation, (ii) implement them on an ARM Cortex-M4F microcontroller, in order to develop a library suitable for embedded systems without an operating system, (iii) find, through a comparative study of the proposed SVD algorithms, the best implementation suitable for a low-resource bare-metal embedded system, (iv) show a practical application to Kalman filtering of an inertial measurement unit (IMU), as an example of how SVD can improve the accuracy of existing algorithms and of its usefulness on a such low-resources system. All these contributions can be used as guidelines for embedded system designers. Regarding the second point, the chosen algorithms have been implemented on ARM Cortex-M4F microcontrollers with very limited hardware resources with respect to more advanced CPUs. Several experiments have been conducted to select which algorithms guarantee the best performance in terms of speed, accuracy and energy consumption.


Electronics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 469
Author(s):  
Hyun Woo Oh ◽  
Ji Kwang Kim ◽  
Gwan Beom Hwang ◽  
Seung Eun Lee

Recently, advances in technology have enabled embedded systems to be adopted for a variety of applications. Some of these applications require real-time 2D graphics processing running on limited design specifications such as low power consumption and a small area. In order to satisfy such conditions, including a specific 2D graphics accelerator in the embedded system is an effective method. This method reduces the workload of the processor in the embedded system by exploiting the accelerator. The accelerator assists the system to perform 2D graphics processing in real-time. Therefore, a variety of applications that require 2D graphics processing can be implemented with an embedded processor. In this paper, we present a 2D graphics accelerator for tiny embedded systems. The accelerator includes an optimized line-drawing operation based on Bresenham’s algorithm. The optimized operation enables the accelerator to deal with various kinds of 2D graphics processing and to perform the line-drawing instead of the system processor. Moreover, the accelerator also distributes the workload of the processor core by removing the need for the core to access the frame buffer memory. We measure the performance of the accelerator by implementing the processor, including the accelerator, on a field-programmable gate array (FPGA), and ascertaining the possibility of realization by synthesizing using the 180 nm CMOS process.


2018 ◽  
Vol 7 (2.7) ◽  
pp. 146
Author(s):  
Lakshmi Prasad Mudarakola ◽  
J K.R. Sastry ◽  
V Chandra Prakash

Thorough testing of embedded systems is required especially when the systems are related to monitoring and controlling the mission critical and safety critical systems. The embedded systems must be tested comprehensively which include testing hardware, software and both together. Embedded systems are highly intelligent devices that are infiltrating our daily lives such as the mobile in your pocket, and wireless infrastructure behind it, routers, home theatre system, the air traffic control station etc. Software now makes up 90% of the value of these devices. In this paper, authors present different methods to test an embedded system using test cases generated through combinatorial techniques. The experimental results for testing a TMCNRS (Temperature Monitoring and Controlling Nuclear Reactor System) using test cases generated from combinatorial methods are also shown.


2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Mohammad J. M. Zedan ◽  
Ali I. Abduljabbar ◽  
Fahad Layth Malallah ◽  
Mustafa Ghanem Saeed

Nowadays, much research attention is focused on human–computer interaction (HCI), specifically in terms of biosignal, which has been recently used for the remote controlling to offer benefits especially for disabled people or protecting against contagions, such as coronavirus. In this paper, a biosignal type, namely, facial emotional signal, is proposed to control electronic devices remotely via emotional vision recognition. The objective is converting only two facial emotions: a smiling or nonsmiling vision signal captured by the camera into a remote control signal. The methodology is achieved by combining machine learning (for smiling recognition) and embedded systems (for remote control IoT) fields. In terms of the smiling recognition, GENKl-4K database is exploited to train a model, which is built in the following sequenced steps: real-time video, snapshot image, preprocessing, face detection, feature extraction using HOG, and then finally SVM for the classification. The achieved recognition rate is up to 89% for the training and testing with 10-fold validation of SVM. In terms of IoT, the Arduino and MCU (Tx and Rx) nodes are exploited for transferring the resulting biosignal remotely as a server and client via the HTTP protocol. Promising experimental results are achieved by conducting experiments on 40 individuals who participated in controlling their emotional biosignals on several devices such as closing and opening a door and also turning the alarm on or off through Wi-Fi. The system implementing this research is developed in Matlab. It connects a webcam to Arduino and a MCU node as an embedded system.


Sign in / Sign up

Export Citation Format

Share Document