scholarly journals On the modeling of droplet transport, dispersion and evaporation in turbulent flows

2005 ◽  
Vol 122 (3) ◽  
pp. 42-55
Author(s):  
Jorge BARATA
Keyword(s):  
Turbulent Flows ◽  
Gas Turbines ◽  
Numerical Study ◽  
Droplet Diameter ◽  
Turbulent Transport ◽  
Three Dimensional ◽  
Turbulent Dispersion ◽  
Droplet Transport ◽  
New Formulation ◽  
Evaporation Models

The present paper presents a numerical study on evaporating droplets injected through a turbulent cross-stream. Several models have been used with more or less success to describe similar phenomena, but much of the reported work deals only with sprays in stagnant surroundings. The ultimate goal of this study is to develop an Eulerian/Lagragian approach to account for turbulent transport, dispersion, evaporation and coupling between both processes in practical spray injection systems, which usually include air flows in the combustion chamber like swirl, tumble and squish in I.C. engines or crossflow in gas turbines. In this work a method developed to study isothermal turbulent dispersion is extended to the case of an array of evaporating droplets through a crossflow, and the performance of two different evaporation models widely used is investigated. The convection terms were evaluated using the hybrid or the higher order QUICK scheme. The dispersed phase was treated using a Lagrangian reference frame. The differences between the two evaporation models and its applicability to the present flow are analysed in detail. During the preheating period of the Chen and Pereira [1] model the droplets are transported far away from the injector by the crossflow, while with the Sommerfeld [2] formulation for evaporation the droplet has a continuous variation of the diameter. This result has profound implications on the results because the subsequent heat transfer and turbulent dispersion is extremely affected by the size of the particles (or droplets). As a consequence, droplet diameter, temperature and mass fraction distributions were found to be strongly dependent on the evaporation model used. So, a new formulation that takes into account also the transport of the evaporating droplets needs to be developed if practical injection systems are to be simulated. Also, in order to better evaluate and to improve the vaporization models more detailed measurements of three-dimensional configurations are required.

scholarly journals A Numerical Study of Three-Dimensional Flow Separation and Wake Development in an Axial Compressor Rotor

1984 ◽  
Author(s):  
C. Hah
Keyword(s):  
Viscous Flow ◽  
Turbulent Flows ◽  
Numerical Study ◽  
Control Volume ◽  
Turbulent Transport ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Computational Procedure ◽  
Navier Stokes Equation ◽  
Compressor Rotor

A computational procedure based on the compressible Reynolds-averaged Navier-Stokes equation has been developed for the viscous flow through an isolated compressor rotor. The numerical scheme is based on fully conservative control volume formulation and solves various conservation equations in fully elliptic form on the rotating coordinates fixed on the rotor. An algebraic Reynolds stress model is used to describe the turbulent transport terms. The numerical procedure has been applied to predict three-dimensional turbulent flows through two different isolated compressor rotors. The detailed quantitative comparisons with two sets of well-documented data show that the developed computational procedure predicts the viscous flow development over the blading and in the wake with the accuracy satisfactory for most engineering purposes; the computer code can be used for the guidance of advanced rotor design.

scholarly journals Numerical Study of Three-Dimensional Surface Jets Emerging from a Fishway Entrance Slot

Water ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1079
Author(s):  
Lena Mahl ◽  
Patrick Heneka ◽  
Martin Henning ◽  
Roman B. Weichert
Keyword(s):  
Boundary Conditions ◽  
Turbulent Flows ◽  
Numerical Study ◽  
Three Dimensional ◽  
Free Water ◽  
Lateral Wall ◽  
Lateral Spreading ◽  
Propagation Length ◽  
Vertical Slot ◽  
Surface Jets

The efficiency of a fishway is determined by the ability of immigrating fish to follow its attraction flow (i.e., its jet) to locate and enter the fishway entrance. The hydraulic characteristics of fishway entrance jets can be simplified using findings from widely investigated surface jets produced by shaped nozzles. However, the effect of the different boundary conditions of fishway entrance jets (characterized by vertical entrance slots) compared to nozzle jets must be considered. We investigate the downstream propagation of attraction jets from the vertical slot of a fishway entrance into a quiescent tailrace, considering the following boundary conditions not considered for nozzle jets: (1) slot geometry, (2) turbulence characteristics of the approach flow to the slot, and (3) presence of a lateral wall downstream of the slot. We quantify the effect of these boundary conditions using three-dimensional hydrodynamic-numeric flow simulations with DES and RANS turbulence models and a volume-of-fluid method (VoF) to simulate the free water surface. In addition, we compare jet propagation with existing analytical methods for describing jet propagations from nozzles. We show that a turbulent and inhomogeneous approach flow towards a vertical slot reduces the propagation length of the slot jet in the tailrace due to increased lateral spreading compared to that of a jet produced by a shaped nozzle. An additional lateral wall in the tailrace reduces lateral spreading and significantly increases the propagation length. For highly turbulent flows at fishway entrances, the RANS model tends to overestimate the jet propagation compared to the transient DES model.

Deposition of Small Particles From Turbulent Flows

2003 ◽  
Author(s):  
Z. Wu ◽  
J. B. Young
Keyword(s):  
Turbulent Flow ◽  
Turbulent Flows ◽  
Channel Flow ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Numerical Study ◽  
Turbulent Channel Flow ◽  
Brownian Diffusion ◽  
Small Particles ◽  
Two Fluid

This paper deals with particle deposition onto solid walls from turbulent flows. The aim of the study is to model particle deposition in industrial flows, such as the one in gas turbines. The numerical study has been carried out with a two fluid approach. The possible contribution to the deposition from Brownian diffusion, turbulent diffusion and shear-induced lift force are considered in the study. Three types of turbulent two-phase flows have been studied: turbulent channel flow, turbulent flow in a bent duct and turbulent flow in a turbine blade cascade. In the turbulent channel flow case, the numerical results from a two-dimensional code show good agreement with numerical and experimental results from other resources. Deposition problem in a bent duct flow is introduced to study the effect of curvature. Finally, the deposition of small particles on a cascade of turbine blades is simulated. The results show that the current two fluid models are capable of predicting particle deposition rates in complex industrial flows.

The Reynold’s Number Effect in High Swirling Flow in Unconfined Burner

2015 ◽  
Vol 72 (4) ◽  
Author(s):  
Norwazan A. R. ◽  
Mohammad Nazri Mohd. Jaafar
Keyword(s):  
Turbulent Flows ◽  
Gas Turbines ◽  
Swirling Flow ◽  
Numerical Study ◽  
Isothermal Condition ◽  
Navier Stokes ◽  
Reacting Flow ◽  
Ansys Fluent ◽  
Inlet Velocity ◽  
Burner Exit

The numerical simulations of swirling turbulent flows in isothermal condition in combustion chamber of burner were investigated. The aim is to characterize the main flow structures and turbulence in a combustor that is relevant to gas turbines. Isothermal flows with different inlet flow velocities were considered to demonstrate the effect of radial velocity. The inlet velocity, Uo is varied from 30 m/s to 60 m/s represent a high Reynolds number up to 3.00 X 105. The swirler was located at the upstream of combustor with the swirl number of 0.895. A numerical study of non-reacting flow in the burner region was performed using ANSYS Fluent. The Reynolds–Averaged Navier–Stokes (RANS) approach method was applied with the standard k-ɛ turbulence equations. The various velocity profiles were different after undergoing the different inlet velocity up to the burner exit. The results of velocity profile showed that the high U0 give better swirling flow patterns.

Calculations of three-dimensional viscous flow in a multiblade centrifugal fan by modelling blade forces

2003 ◽  
Vol 217 (3) ◽  
pp. 287-297 ◽  
Author(s):  
S-J Seo ◽  
K-Y Kim ◽  
S-H Kang
Keyword(s):  
Mathematical Model ◽  
Turbulent Flows ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Fan ◽  
Complex Flows ◽  
Flow Through ◽  
Volume Method ◽  
The Mathematical Model

A numerical study is presented for Reynolds-averaged Navier-Stokes analysis of three-dimensional turbulent flows in a multiblade centrifugal fan. Present work aims at development of a relatively simple analysis method for these complex flows. A mathematical model of impeller forces is obtained from the integral analysis of the flow through the impeller. A finite volume method for discretization of governing equations and a standard k-ɛ model as turbulence closure are employed. For the validation of the mathematical model, the computational results for velocity components, static pressure, and flow angles at the exit of the impeller were compared with experimental data. The comparisons show generally good agreement, especially at higher flow coefficients.

Numerical Study of the Heat Transfer in Micro Gas Turbines

2006 ◽  
Vol 129 (4) ◽  
pp. 835-841 ◽  
Author(s):  
T. Verstraete ◽  
Z. Alsalihi ◽  
R. A. Van den Braembussche
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Numerical Study ◽  
Three Dimensional ◽  
High Heat ◽  
Large Temperature ◽  
Radial Compressor ◽  
Micro Gas Turbine ◽  
High Heat Transfer ◽  
The Impact

This paper presents a numerical investigation of the heat transfer inside a micro gas turbine and its impact on the performance. The large temperature difference between turbine and compressor in combination with the small dimensions results in a high heat transfer causing a drop in efficiency of both components. Present study aims to quantify this heat transfer and to reveal the different mechanisms that contribute to it. A conjugate heat transfer solver has been developed for this purpose. It combines a three-dimensional (3D) conduction calculation inside the rotor and the stator with a 3D flow calculation in the radial compressor, turbine and gap between stator and rotor. The results for micro gas turbines of different size and shape and different material characteristics are presented and the impact on performance is evaluated.

A Numerical Study of Turbulent Flow in Helical Static Mixers

2006 ◽  
Author(s):  
Ramin K. Rahmani ◽  
Anahita Ayasoufi ◽  
Theo G. Keith
Keyword(s):  
Turbulent Flow ◽  
Molecular Diffusion ◽  
Stokes Equations ◽  
Numerical Study ◽  
Critical Role ◽  
Three Dimensional ◽  
Turbulent Dispersion ◽  
Working Fluid ◽  
Static Mixer ◽  
Static Mixers

Many processing applications call for the addition of small quantities of chemicals to working fluid. Hence, fluid mixing plays a critical role in the success or failure of these processes. An optimal combination of turbulent dispersion down to eddies of the Kolmogoroff scale and molecular diffusion would yield fast mixing on a molecular scale which in turn favors the desired reactions. Helical static mixers can be used for those applications. The range of practical flow Reynolds numbers for these mixers in industry is usually from very small (Re ∼ 0) to moderate values (Re ∼ 5000). In this study, a helical static mixer is investigated numerically using Lagrangian methods to characterize mixer performance under turbulent flow regime conditions. A numerical simulation of turbulent flows in helical static mixers is employed. The model solves the three-dimensional, Reynolds-averaged Navier-Stokes equations, closed with the Spalart-Allmaras turbulence model, using a second-order-accurate finite-volume numerical method. Numerical simulations are carried out for a six-element mixer, and the computed results are analyzed to elucidate the complex, three-dimensional features of the flow. Using a variety of predictive tools, mixing results are obtained and the performance of static mixer under turbulent flow condition is studied.

Numerical Investigation of the Three-Dimensional Flow Structure About a Revolving Wing

2012 ◽  
Author(s):  
Daniel J. Garmann ◽  
Miguel R. Visbal ◽  
Paul D. Orkwis
Keyword(s):  
Turbulent Flows ◽  
Numerical Study ◽  
Three Dimensional ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Vortex System ◽  
Aerodynamic Loads ◽  
Eddy Simulation ◽  
Data Reduction Technique ◽  
The Stability

A numerical study is conducted to examine the vortex structure about a revolving wing in quiescent flow employing a high-fidelity, implicit large eddy simulation (ILES) technique found to be effective in simulating flows that exhibit interspersed regions of laminar, transitional, and turbulent flows. The revolving wing configuration consists of a single, aspect ratio one rectangular plate extended out a distance of 0.5 chords from the origin. Shortly after the onset of the motion, the rotating wing generates a stable and coherent vortex system across the leading edge and wing root that remains throughout the motion. The aerodynamic loads are also analyzed and found to remain mostly constant during the maneuver. Transitional effects on the vortex system are investigated over a range of Reynolds numbers (3,000 < Re < 15,000). It is found that higher Reynolds numbers promote more breakdown of the leading edge and root vortices, but do not alter the stability of the vortex system. The aerodynamic loads also show little sensitivity to Reynolds number with the higher Reynolds numbers producing only moderately higher forces. Comparisons with recent experimental PIV measurements using a PIV-like data reduction technique applied to the computational solution show very favorable agreement with the mid-span velocity and vorticity contours.

Computation of Three-Dimensional Turbulent Flows in a Pipe Junction with Reference to Engine Inlet Manifolds

1992 ◽  
Vol 206 (4) ◽  
pp. 285-296 ◽  
Author(s):  
H Fu ◽  
M J Tindal ◽  
A P Watkins ◽  
M Yianneskis
Keyword(s):  
Turbulent Flows ◽  
Combustion Engine ◽  
Laser Doppler Anemometry ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulence Energy ◽  
Numerical Predictions ◽  
Split Ratio ◽  
Inlet Manifold ◽  
Good Agreement

This paper presents a numerical study of the flows in an internal combustion engine inlet manifold. The three-dimensional turbulent flows through a single branched manifold were simulated using the κ-ɛ model of turbulence. The flow structure was characterized in detail and the effects of the flow split ratio and inlet flowrate were investigated. Detailed measurements were performed to validate the numerical predictions, using laser Doppler anemometry. Good agreement was obtained between the predicted and the measured mean velocities. The predicted levels of turbulence energy are in qualitative agreement with the measurements.

scholarly journals Numerical Study of Super-cooled droplet impingement on Aeroengine

Mechanika ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 25-30
Author(s):  
Yan TAN ◽  
Wuguo WEI
Keyword(s):  
Flow Field ◽  
Data Exchange ◽  
Collection Efficiency ◽  
Numerical Study ◽  
Mixed Boundary ◽  
Droplet Diameter ◽  
Three Dimensional ◽  
Liquid Water Content ◽  
Euler Method ◽  
Nose Cone

In this work, a large bypass ratio engine was taken as the research object. The impingement property of droplets with various diameters including SLD (Super-cooled Large Droplet) was obtained by Euler method based on Mundo model. The grid models of nose cone, fan, guild vanes in bypass duct and core duct were established in segments firstly. The mixed boundary was used to realize the data exchange between different flow fields. Then the Spalart-Allmaras turbulence model was applied to calculate the three dimensional engine flow field. Based on the flow field result, the droplet trajectory was calculated by Euler multiphase flow method. The LWC (Liquid Water Content), droplet collection efficiency and the effect of droplet diameter on impingement law were obtained. The method used in this paper and results could provide some references for subsequent engine icing calculation and anti-icing system design.

Sign in / Sign up

Export Citation Format

Share Document