scholarly journals STUDI ISOTEM DAN KINETIKA ADSORPSI BAHAN ORGANIK ALAMI (BOA) PADA AIR GAMBUT TERHADAP KARBON AKTIF KAYU ULIN DENGAN SISTEM BATCH

2021 ◽  
Vol 4 (2) ◽  
pp. 1-12
Author(s):  
Nida Noviani Elma ◽  
Mahmud Mahmud ◽  
Badaruddin Mu'min
Keyword(s):  
Langmuir Model

Air gambut di Indonesia khususnya di Kalimantan Selatan sangat berlimpah dan memiliki potensi untuk dijadikan sebagai sumber air bersih. Keberadaan bahan organik yang tinggi di dalam air gambut  membuat air gambut perlu dilakukan pengolahan terlebih dahulu. Salah satu pengolahan yang dapat dilakukan yaitu dengan proses adsorpsi. Adsorpsi suatu zat pada permukaan adsorben bergantung pada beberapa faktor dan memiliki pola isoterm dan kinetika tertentu. Penelitian ini bertujuan untuk menentukan model isoterm, dan model kinetika yang sesuai pada adsorpsi bahan organik alami (BOA) terhadap karbon aktif kayu ulin. Metode dalam penelitian ini menggunakan proses adsorpsi dengan adsorben karbon aktif kayu ulin. Model isoterm yang digunakan yaitu model Langmuir, model Freundlich, dan model Redlich-Peterson, sedangkan model kinetika yang digunakan ialah model Pseudo Orde Satu, Pseudo Orde Dua, dan Freundlich Modifikasi. Model isoterm Redlich-Peterson merupakan model yang sesuai untuk adsorpsi BOA air gambut terhadap karbon aktif kayu ulin dan model kinetika yang sesuai untuk adsorpsi BOA air gambut terhadap karbon aktif kayu ulin adalah model Pseudo Orde Dua.

REMOVAL OF HEAVY METAL Cr (II), Ni (II), Cu (II), Zn (II), Cd (II), Pb (II) IONS FROM AQUEOUS SOLUTION BY MENTHA PIPERITA EXTRACT

2020 ◽  
pp. 15-20
Author(s):  
Ersin Yucel ◽  
Mine Yucel
Keyword(s):  
Aqueous Solution ◽  
Metal Ions ◽  
High Efficiency ◽  
Correlation Coefficients ◽  
Langmuir Model ◽  
Mentha Piperita ◽  
Freundlich Model ◽  
Biosorption Capacity ◽  
Peppermint Extract ◽  
The Stability

In this study, the usage of the peppermint (Mentha piperita) for extracting the metal ions [Mg (II), Cr (II), Ni (II), Cu (II), Zn (II), Cd (II), Pb (II)] that exist at water was investigated. In order to analyze the stability properties, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms were used at removing the metal ions and the highest correlation coefficients (R2) were obtained at Langmuir isotherm. Therefore, it is seen that the Langmuir model is more proper than the Freundlich model. However, it was found that the correlation coefficients of removing Ni and Cd is higher at Freundlich model than Langmuir and low at Dubinin-Radushkevich isotherm. It is established that the biosorption amount increase depends on the increase of biosorbent and it can be achieved high efficiency (95%) even with small amount (0.6 mg, peppermint extract) at lead ions. It is also determined that the peppermint extracted that is used at this study shows high biosorption capacity for metal ions and can be used for immobilization of metals from polluted areas.

scholarly journals Polyelectrolyte Functionalisation of Track Etched Membranes: Towards Charge-Tuneable Adsorber Materials

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 509
Author(s):  
Lisa Wiedenhöft ◽  
Mohamed M. A. Elleithy ◽  
Mathias Ulbricht ◽  
Felix H. Schacher
Keyword(s):  
Methylene Blue ◽  
Heavy Metal Ions ◽  
Glycolic Acid ◽  
Organic Dyes ◽  
Langmuir Model ◽  
Surface Grafting ◽  
Hydraulic Permeability ◽  
Cylindrical Pores ◽  
Model Substances ◽  
External Stimuli

Porous adsorber membranes are promising materials for the removal of charged pollutants, such as heavy metal ions or organic dyes as model substances for pharmaceuticals from water. Here, we present the surface grafting of polyethylene terephthalate (PET) track-etched membranes having well defined cylindrical pores of 0.2 or 1 µm diameter with two polyelectrolytes, poly(2-acrylamido glycolic acid) (PAGA) and poly(N-acetyl dehydroalanine) (PNADha). The polyelectrolyte functionalised membranes were characterised by changes in wettability and hydraulic permeability in response to the external stimuli pH and the presence of Cu2+ ions. The response of the membranes proved to be consistent with functionalisation inside the pores, and the change of grafted polyelectrolyte macro-conformation was due to the reversible protonation or binding of Cu2+ ions. Moreover, the adsorption of the model dye methylene blue was studied and quantified. PAGA-grafted membranes showed an adsorption behavior following the Langmuir model for methylene blue.

Biopolymer-induced calcium phosphate scaling in membrane-based water treatment systems: Langmuir model films studies

2016 ◽  
Vol 143 ◽  
pp. 233-242 ◽  
Author(s):  
Yara N. Dahdal ◽  
Yoram Oren ◽  
Dietmar Schwahn ◽  
Vitaliy Pipich ◽  
Moshe Herzberg ◽  
...  
Keyword(s):  
Water Treatment ◽  
Calcium Phosphate ◽  
Langmuir Model

scholarly journals A Novel and Efficient Metal Oxide Fluoride Absorbent for Drinking Water Safety and Sustainable Development

2021 ◽  
Vol 13 (2) ◽  
pp. 883
Author(s):  
Changjuan Dong ◽  
Xiaomei Wu ◽  
Zhanyi Gao ◽  
Peiling Yang ◽  
Mohd Yawar Ali Khan
Keyword(s):  
Sustainable Development ◽  
Drinking Water ◽  
Metal Oxide ◽  
Environmental Sustainability ◽  
Environmentally Friendly ◽  
Langmuir Model ◽  
Maximum Adsorption Capacity ◽  
Low Carbon ◽  
Water Safety ◽  
Solution Ph

Inefficient and non-environmentally friendly absorbent production can lead to much resource waste and go against low carbon and sustainable development. A novel and efficient Mg-Fe-Ce (MFC) complex metal oxide absorbent of fluoride ion (F−) removal was proposed for safe, environmentally friendly, and sustainable drinking water management. A series of optimization and preparation processes for the adsorbent and batch experiments (e.g., effects of solution pH, adsorption kinetics, adsorption isotherms, effects of coexisting anions, as well as surface properties tests) were carried out to analyze the characteristics of the adsorbent. The results indicated that optimum removal of F− occurred in a pH range of 4–5.5, and higher adsorption performances also happened under neutral pH conditions. The kinetic data under 10 and 50 mg·g−1 were found to be suitable for the pseudo-second-order adsorption rate model, and the two-site Langmuir model was ideal for adsorption isotherm data as compared to the one-site Langmuir model. According to the two-site Langmuir model, the maximum adsorption capacity calculated at pH 7.0 ± 0.2 was 204 mg·g−1. The adsorption of F− was not affected by the presence of sulfate (SO42−), nitrate (NO3−), and chloride (Cl−), which was suitable for practical applications in drinking water with high F− concentration. The MFC adsorbent has an amorphous structure, and there was an exchange reaction between OH− and F−. The novel MFC adsorbent was proven to have higher efficiency, better economy, and environmental sustainability, and be more environmentally friendly.

Water-soluble polymeric particle embedded cryogels: Synthesis, characterisation and adsorption of haemoglobin

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Kadir Erol ◽  
Melda Bolat Bülter ◽  
Dursun Ali Köse ◽  
Hatice Kaplan Can
Keyword(s):  
Copper Ions ◽  
Langmuir Model ◽  
Water Soluble ◽  
Hydroxyethyl Methacrylate ◽  
Adsorption Ability ◽  
Adsorption Interaction ◽  
Polymeric Particle ◽  
Adsorption Desorption ◽  
Desorption Cycle ◽  
Soluble Poly

Abstract Making cryogels, which are among today’s accepted adsorbents, more functional with different methods, has been one of the subjects spent overtime. In this study, water-soluble poly(maleic anhydride-alt-acrylic acid) polymer embedded in poly(2-hydroxyethyl methacrylate) cryogels. Copper ions were then immobilised to this structure, and this polymer was used for adsorption of haemoglobin from aqueous systems. Adsorption interaction was carried out on an electrostatic basis, and approximately 448.62 mg haemoglobin/g polymer adsorption capacity value was obtained. It was found that the same material has managed to maintain its adsorption ability by 90.3% even after the use of it five times in the adsorption/desorption cycle. The adsorption interaction was determined to be appropriate for the Langmuir model by isotherm studies. The change in Gibbs free energy value was calculated as −2.168 kJ/mol.

scholarly journals An Investigation into the Adsorption of Aniline from Aqueous Solution Using H-Beta Zeolites and Copper-Exchanged Beta Zeolites

2005 ◽  
Vol 23 (3) ◽  
pp. 255-266 ◽  
Author(s):  
J. O'Brien ◽  
T. Curtin ◽  
T.F. O'Dwyer
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Zeolite Beta ◽  
Langmuir Model ◽  
Beta Zeolite ◽  
Copper Leaching ◽  
Beta Zeolites ◽  
The Stability ◽  
Ph Range ◽  
Adsorbent Materials

Zeolite beta, a large-pore zeolite, was investigated in this study with a view to examining it as a potential adsorbent for the removal of aniline from aqueous solutions. Two different metal-loaded zeolites were prepared by exchanging H-beta zeolite (SiO2/Al2O3 = 75:1) with copper. The influence of exchanged copper on the uptake level was assessed. The effect of varying the silica-to-alumina ratio of the H-beta zeolite on the aniline uptake level was also examined, using three different H-beta zeolites with ratios of 25:1, 75:1 and 150:1 as adsorbents. The sorption experiments indicated an uptake level of ca. 110–120 mg/g for each zeolite and this level was also adsorbed by the copper-modified H-beta zeolites (SiO2/Al2O3 = 75:1). In all cases, the adsorption process followed the Langmuir model for adsorption and the level of aniline adsorbed was largely unaffected by a change in temperature or the presence of extra framework copper. The stability of the exchanged copper on these zeolites was then examined by measuring the quantity of copper leached from each zeolite into solution as a function of pH. Minimum copper leaching was observed in the pH range 5–11. This provided a stable pH working range for the adsorbent materials.

Synthesis, Characterization and Adsorption Studies of a Graphene Oxide/Polyacrylic Acid Nanocomposite Hydrogel

2021 ◽  
Vol 19 (9) ◽  
pp. 46-54
Author(s):  
Makarim A. Mahdi ◽  
Aymen A.R. Jawad ◽  
Aseel M. Aljeboree ◽  
Layth S. Jasim ◽  
Ayad F. Alkaim
Keyword(s):  
Industrial Effluents ◽  
Langmuir Model ◽  
Isotherm Models ◽  
Nanocomposite Hydrogel ◽  
Adsorption System ◽  
Order Model ◽  
Solution Ph ◽  
Freundlich Model ◽  
Dye Sorption ◽  
Pseudo Second Order

The AAc/GO nanocomposite hydrogel was successfully employed as a polymeric Nano sorbent of the removal efficiency of M G dye from the model. The complication of the mechanism of the adsorption system was completely exposed by examining how solution pH affects adsorption, Ionic strength isotherm models, kinetic models, and thermodynamics. The adsorption of the MG dye was greatly dependent on the solution pH. The Freundlich model has been demonstrated to be the most accurate in describing the MG dye sorption, whilst the Langmuir model was shown to be the least accurate. Additionally, these integrated mechanisms fit nicely within the framework of a pseudo-second-order model. Additionally, the contact time at equilibrium short (ten minutes) required to MG removes demonstrates the AAc/GO nanocomposite hydrogel can be considered an efficient and potentially useful adsorbent for MG removal from industrial effluents.

scholarly journals Removal of anionic surfactants by sorption onto Aminated Mesoporous Carbon

2013 ◽  
Vol 19 (3) ◽  
pp. 347-357 ◽  
Author(s):  
S.E. Moradi ◽  
J. Khodaveisy ◽  
R. Dashti
Keyword(s):  
Contact Time ◽  
Mesoporous Carbon ◽  
Anionic Surfactants ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Langmuir Model ◽  
Carbon Adsorbents ◽  
Solution Ph ◽  
Batch Mode ◽  
Ft Ir

Direct and indirect releases of large quantities of surfactants to the environment may result in serious health and environmental problems. Therefore, surfactants should be removed from water before release to the environment or delivery for public use. In the present work, the removal of anionic surfactants, benzene sulfonate (BS), p-toluene sulfonate (TS) and 4-octylbenzene sulfonate (OBS) from water by adsorption onto Amino modified mesoporous carbon (AMC) were studied. The AMC surface chemistry and textural properties was characterized by nitrogen adsorption, XRD and FT-IR analyses. Experiments were conducted in batch mode with the variables such as amount of contact time, solution pH, dose of adsorbent and temperature. Finally, the adsorption isotherms of anionic surfactants on mesoporous carbon adsorbents were in agreement with a Langmuir model. AMC has shown higher anionic surfactants adsorption capacity than the untreated mesoporous carbon, which can explain by strong interaction between anionic surfactant and cationic surface of adsorbent.

scholarly journals Platinum surface complexes as precursors for H2–O2 recombination catalysts

2017 ◽  
Vol 35 (7-8) ◽  
pp. 735-743 ◽  
Author(s):  
Olesya B Volovenko ◽  
Olga A Zaporozhets ◽  
Vladyslav V Lisnyak ◽  
Olga Yu Boldyrieva
Keyword(s):  
Silica Gel ◽  
Platinum Metal ◽  
Langmuir Model ◽  
Ammonium Salts ◽  
Platinum Surface ◽  
Chloride Complexes ◽  
Surface Complexes ◽  
Acidic Solutions ◽  
Modified Surface ◽  
Excellent Stability

In this work, the adsorption of platinum (II, IV) chloride complexes from acidic solutions on silica gel modified with quaternary ammonium salts (QAS) was studied. The uptake of the platinum chloride complexes is caused by the formation of ionic (QAS+)2[PtCl x]2− ( x = 4, 6) associates on the surface of silica gel. The isotherms of adsorption are fitted by the Langmuir model. The maximum capacity for [PtCl4]2− and [PtCl6]2− is 0.99 and 1.13 mmol/g, correspondingly. The respective adsorption constants KL = 6.8 and 10 × 105 l/mol prove the high affinity of the adsorbates to the QAS-modified surface. Platinum metal nanoparticles supported on the surface of the silica gel were prepared by reducing the adsorbed platinum (II, IV) complexes. Such nanoparticles functioning at the moderate temperature regime have demonstrated a reasonable catalytic activity for the hydrogen and oxygen recombination, and an excellent stability over 35 cycles of the reaction.

scholarly journals Phosphate and Ammonium Removal from Wastewaters Using Natural-Based Innovative Bentonites Impacting on Resource Recovery and Circular Economy

Molecules ◽  
2021 ◽  
Vol 26 (21) ◽  
pp. 6684
Author(s):  
Miltiadis Zamparas ◽  
Grigorios L. Kyriakopoulos ◽  
Marios Drosos ◽  
Vasilis C. Kapsalis
Keyword(s):  
Circular Economy ◽  
Low Cost ◽  
Resource Recovery ◽  
Sem Analysis ◽  
Langmuir Model ◽  
Treated Wastewater ◽  
Ammonium Removal ◽  
Different Types ◽  
Long Time ◽  
Ph Range

The research objective of the study is the estimation of a novel low-cost composite material f-MB (Fe-modified bentonite) as a P and N adsorbent from wastewaters. Τhe present study aimed at examining the phosphate and ammonium removal efficiency from different types of wastewater using f-MB, by conducting bench-scale batch experiments to investigate its equilibrium characteristics and kinetics. The SEM analysis revealed that the platelets of bentonite in f-MB do not form normal bentonite sheets, but they have been restructured in a more compact formation with a great porosity. Regarding the sorption efficiencies (Qm), the maximum phosphate sorption efficiencies (Qm) calculated using the Langmuir model were 24.54, 25.09, 26.13, 24.28, and 23.21 mg/g, respectively, for a pH range of 5 to 9. In addition, the maximum NH4+-N adsorption capacities (Qm) calculated from the Langmuir model were 131.8, 145.7, 168.5, 156.7, and 159.6 mg/g, respectively, for a pH range from 5 to 9. Another important finding of this study is that f-MB can recover P from treated wastewater impacting on resource recovery and circular economy (CE). The modified clay f-MB performed the phosphate and ammonium recovery rates of 80% and 78.5%, respectively. Finally, f-MB can slowly release the largest proportion of phosphate and ammonium ions for a long time, thus extending the application of the f-MB material as a slow-release fertilizer and soil improver.

Sign in / Sign up

Export Citation Format

Share Document