Standardization the effect of shape of aggregates with respect to compressive strength of concrete

2018 ◽  
Vol 9 (1) ◽  
pp. 1
Author(s):  
Md. Shafiqul Islam ◽  
Md. Abul Kalam Azad ◽  
Arup Ratan Sarker
Keyword(s):  
Compressive Strength ◽  
Physicomechanical Properties ◽  
Concrete Compressive Strength ◽  
Test Compaction ◽  
Concrete Cylinder ◽  
Severe Effect ◽  
Different Types ◽  
Mixture Volume ◽  
Different Shapes ◽  
Compressive Strength Of Concrete

It is proved that aggregate’s types have the severe effect on physicomechanical properties of concrete as aggregate covered almost 70 to 80 percent of the total volume of concrete. The effect of Flaky and Elongated aggregates on strength, durability, and workability of concrete has often been qualitatively expressed. The aim of this work is establishing the same quantitatively. M25 grade concrete for different ratios of weights of Elongated to normal aggregate, Flaky to normal aggregate and combined Flaky & Elongated aggregate to normal aggregate was tested for compressive strength at 28 days concrete. Three different types of aggregates were employed in the investigation, namely; normal aggregate, Elongated aggregate, and Flaky aggregate. Density and water absorption also kept constant to identify the effects on properties of concrete only for differences in shape. Thirty-six concrete cylinder was cast at 28 days. Varying dosages of Normal aggregate (60%, 65%, 70%, 75%,80% 85%), flaky aggregate (40%, 35%, 30%, 25%, 20%, 15%), elongated aggregate (40%, 35%, 30%, 25%, 20%, 15%), by mixture volume and length of 12inch (304.8 mm) & diameter of 6inch (152.4 mm) cylinder were used to test. Compaction was done by temping rod. Concrete cylinder was tested at the age of 28 days of curing. This study proposed of mixing three different types of aggregate in concrete. Compressive strength of concrete was measured by the effect of three different shapes of aggregates of varying dosages.

scholarly journals THE INFLUENCE OF RIVER AND VOLCANIC SAND AS COATINGS ON POLYPROPYLENE WASTE COARSE AGGREGATE TOWARDS CONCRETE COMPRESSIVE STRENGTH

2020 ◽  
Vol 82 (4) ◽  
Author(s):  
Gandjar Pamudji ◽  
Madsuri Satim ◽  
Mochamad Chalid ◽  
Heru Purnomo
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Experimental Tests ◽  
Concrete Compressive Strength ◽  
Replacement Ratio ◽  
River Sand ◽  
Aggregate Concrete ◽  
Different Types ◽  
Compressive Strength Of Concrete

One of the most important factors used to determine the compressive strength of concrete is its aggregate and matrix adhesion. This study examines the surface properties of polypropylene (PP) waste coarse aggregate (PWCA) to determine the influence of sand. The PWCA was made from the PP waste and different types of coating such as PWCA-R (river sand) and PWCA-V (volcanic sand), with experimental tests conducted on the physical properties of sand and PWCA, while the compressive strength, FESEM and density of polypropylene waste coarse aggregate concrete (PWCAC). Concrete specimens were prepared by replacing natural coarse aggregate with PWCA in percentages of 0%, 25%, 50%, 75%, and 100%, varying the water-cement ratio by 0.3 and 0.42 and using polypropylene (PP) waste coarse aggregate (PWCA-R and PWCA-V) as the coating material. The results showed that fineness modulus (F.M) and water absorption of the river sand was higher compared to volcanic sand. The PWCA-V had higher density and specific gravity compared to PWCA-R. On the other hand, water absorption of the PWCA-V was lower than PWCA-R. The PWCA concrete had density which varies from 1740 kg/m3 to 2074 kg/m3. For both, the PWCA concrete compressive strength at 28 days with a 100% replacement ratio was reduced by 43% to 55% compared to the natural coarse aggregate (NCA) concrete with 0.3 and 0.42 water-cement ratios. Also, the structural efficiency of PWCAC decreased with an increase in replacement ratio. River sand adhered to the PWCA surface resulted in a better compressive strength value compared to the volcanic sand. 

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

scholarly journals Pengaruh Pemanfaatan Abu Tumbuhan Perumpung Terhadap Peningkatan Kuat Tekan Beton K300

Jurnal Tekno ◽  
2021 ◽  
Vol 18 (2) ◽  
pp. 11-20
Author(s):  
Ahmad Junaidi ◽  
R Dewo Hiraliyamaesa Hariyanto
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Wild Plant ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Compressive Strength Of Concrete ◽  
Test Objects

Perumpung (Eulalia japonica) is a wild plant that usually grows on the banks of river. The locals consider this plant as a waste/pest, but the authors are interested in researching perumpung because they are similar to bamboo, sugarcane and other fibrous plants. In this study, the authors aims to compare the compressive strength of normal concrete with the compressive strength of concrete added with Perumpung ash at 28-days-old K-300. The study used a cube-shaped test object (15 x 15 x 15 cm) with 6 samples for each condition. The total number of test objects is 48, which consists of 8 conditions, namely normal conditions and 5%, 7.5%, 10%, 12.5%, 15%, 17.5% and 20% addition of perumpung ash by cement weight. The results obtained that the compressive strength of 28-days-old concrete under normal conditions was 316,060 kg/cm2 and the addition of 5% ash was 331.583 kg/cm2, 7.5% was 337.181 kg/cm2, 10% was 341.813 kg/cm2, 12 ,5% is 347,045 kg/cm2, 15% is 353,889 kg/cm2, 17.5% is 311,160 kg/cm2 and 20% is 298.44 kg/cm2. From the results above it can be concluded that the addition of 15% Perumpung Ash to the concrete mixture increases the maximum characteristic concrete compressive strength by 353.889 kg/cm2.

scholarly journals Kuat Tekan Beton Mutu Tinggi dengan Memanfaatkan Fly Ash dan Bubuk Kaca Sebagai Bahan Pengisi

2020 ◽  
Vol 20 (01) ◽  
pp. 61-68
Author(s):  
Siska Apriwelni ◽  
Nugraha Bintang Wirawan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Glass Powder ◽  
Concrete Mixture ◽  
Strength Testing ◽  
Concrete Compressive Strength ◽  
High Quality ◽  
Glass Waste ◽  
Powder Addition ◽  
Compressive Strength Of Concrete

(ID) Penelitian ini membahas pengaruh kuat tekan beton mutu tinggi dengan memanfaatkan limbah fly ash dan limbah kaca. Tujuan dari penelitian ini untuk mengetahui kuat tekan beton pada masing-masing variasi, mengetahui persentase campuran beton untuk menghasilkan kuat tekan maksimum, dan mengetahui apakah fly ash dan serbuk kaca efektif digunakan secara bersamaan sebagai bahan campuran beton. Komposisi fly ash terdiri dari 5 variasi yaitu persentase 0%, 5%, 10%, 15%, dan 20%. Sedangkan untuk komposisi serbuk kaca terdiri dari 2 variasi yaitu persentase 5% dan 10%. Jumlah benda uji 30 buah silinder berukuran diameter 15 cm dan tinggi 30 cm dengan 3 benda uji untuk setiap variasi. Perencanaan campuran beton menggunakan SNI 03-2834-2000 yang dimodifikasi. Pengujian kuat tekan diuji pada umur beton 28 hari. Beton dengan fly ash 0% dan serbuk kaca 10% memiliki kuat tekan paling tinggi dibandingkan dengan beton dengan tambahan fly ash, yaitu 46,77%. Selain itu, dapat disimpulkan bahwa semakin bertambahnya jumlah persentase serbuk kaca yang digunakan menunjukkan bahwa kuat tekan beton semakin bertambah juga. Penambahan fly ash pada campuran beton mempengaruhi kuat tekan beton yang dihasilkan. Pada variasi fly ash 0% memiliki kuat tekan tertinggi baik pada saat campuran serbuk kaca 5%dan 10%. Variasi fly ash 15% adalah kondisi optimum campuran beton dengan kuat tekan beton yaitu 43,31 Mpa. Kedua limbah ini dapat dikombinasikan dan dimanfaatkan dengan baik dan digunakan dalam pembuatan beton mutu tinggi. (EN) This study discusses the effect of high quality concrete by utilizing fly ash and glass waste. The purpose of this study is to determine the compressive strength of concrete in each variation, to determine the contribution of concrete to produce compressive strength, and to find out that fly ash and glass powder are effectively used in full as a concrete admixture. Fly ash composition consists of 5 variations, namely the percentage of 0%, 5%, 10%, 15%, and 20%. While for the composition of glass powder consists of 2 variations, namely the percentage of 5% and 10%. The number of specimens is 30 cylinders with a diameter of 15 cm and a height of 30 cm with 3 specimens for each variation. Concrete mixture planning using SNI 03-2834-2000 was developed. Compressive strength testing on concrete age 28 days. Concrete with 0% fly ash and 10% glass powder have the highest compressive strength compared to concrete with additional fly ash, which is 46.77%. In addition, it can increase the amount of glass powder addition that is used to show the concrete compressive strength is increasing as well. The addition of fly ash in the concrete mixture has an effect on the compressive strength of the concrete produced. In the variation of 0% fly ash has the highest compressive strength when the glass powder mixture of 5% and 10%. The 15% fly ash variation is the optimal concrete mixture with compressive strength of 43.31 MPa. These two wastes can be combined and utilized properly and are used in making high quality concrete.  

The Effect of Different Curing Conditions on Compressive Strength of Concrete

2017 ◽  
Vol 60 (3) ◽  
pp. 147-153
Author(s):  
Muhammad Arslan ◽  
Muhammad Asif Saleem ◽  
Maria Yaqub ◽  
Muhammad Saleem Khan
Keyword(s):  
Compressive Strength ◽  
Research Work ◽  
Concrete Structures ◽  
Strength Test ◽  
The Other ◽  
Cylindrical Shape ◽  
Curing Conditions ◽  
Compressive Strength Test ◽  
Different Types ◽  
Compressive Strength Of Concrete

The focus of this research work was to analyse the effect of different types of curing oncompressive strength of concrete structures. For this purpose, 54 test specimens of cylindrical shape wereprepared. These specimens were cured with different methods and were tested on different age days toanalyse the effect of curing on compressive strength. Test specimens cured with conventional water curingmethod gives the highest results as compared to the other adopted methods.

Experimental Study of Compression for Multi-Scale Polypropylene Fiber Concrete

2012 ◽  
Vol 174-177 ◽  
pp. 1584-1588 ◽  
Author(s):  
Ning Hui Liang ◽  
Xin Rong Liu ◽  
Ji Sun
Keyword(s):  
Compressive Strength ◽  
Polypropylene Fiber ◽  
Plain Concrete ◽  
Compression Tests ◽  
Concrete Compressive Strength ◽  
Hybrid Fiber ◽  
Multi Scale ◽  
Fine Fiber ◽  
Fiber Concrete ◽  
Compressive Strength Of Concrete

Through compression tests on 30 plain concrete and polypropylene fiber concrete specimens with the dimensions of 100mm × 100mm × 100mm , studied the influence of the different scales of polypropylene fiber and hybrid fiber on concrete compressive strength and compressive deformation. The results showed that: the compressive strength of concrete for single-doped fiber has little effect to improve concrete compressive strength, some even get lower,but mixing-doped coarse-fine fiber had increased 6.2%~13.7%. Doped-fiber can improve the concrete compressive toughness, it's enhancement sort: mixing-doped coarse-fine fiber concrete > single-doped coarse fiber concrete > single-doped fine fiber concrete> plain concrete

scholarly journals Penggunaan Limbah Nikel Sebagai Material Subtitusi Agregat Kasar Pada Beton K.250

2021 ◽  
Vol 2 (1) ◽  
pp. 29-36
Author(s):  
Muhammad Muhsar ◽  
Abdul Kadir ◽  
Sulaiman Sulaiman
Keyword(s):  
Compressive Strength ◽  
Los Angeles ◽  
Specific Gravity ◽  
Moisture Content ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Test Standards ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

The purpose of this study was to Analyze the characteristics of theaggregates used in concrete mixtures and analyze how muchincrease in compressive strength of concrete with a variation ofnickel slag substitution 0%, 5%, 15%, 25% compared with normalconcrete. The characteristics of the material examined are watercontent, sludge content, specific gravity and absorption, volumeweight, abrasion with los angeles machines, and filter analysis.While the large increase in compressive strength of concrete can betested at the age of 7 days, 14 days, 28 days and 35 days. From the results of the analysis of the characteristics of nickel slagwaste in concrete mixes meet the test standards in concretemixtures, with a moisture content of 0.86%, sludge content of 0.44%,specific gravity of 2.94 gr / cm3, volume weight of 1.76 gr / cm3,abrasion 36.07%. And a large increase in compressive strength ofconcrete with a variation of nickel slag substitution of 0%, 5%, 15%,25% compared to normal concrete is increasing. The highestpercentage increase in concrete compressive strength is found inconcrete compressive strength between a variation of 15% with avariation of 25% at 14 days concrete age, with a percentage increasein value of 13.13%.

scholarly journals PENGARUH CAMPURAN ABU SEKAM PADI DAN ABU ARANG TEMPURUNG SEBAGAI PENGGANTI SEBAGIAN AGREGAT HALUS TERHADAP KUAT TEKAN BETON

2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Agung Prayogi
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength ◽  
By Products

Abstract Concrete is the most widely used material throughout the world and innovations continue to be carried out to produce efficient development. Shell charcoal ash and rice husk ash are industrial by-products which have the potential to replace sand for concrete mix, especially in Indragiri Hilir. The research with the title "Effect of Mixture of Rice Husk Ash and Shell Ash Ashes as Substitute for Some Fine Aggregates Against Concrete Compressive Strength" aims to prove the effect of a mixture of shell charcoal ash and husk ash to replace some of the sand to produce maximum compressive strength. Concrete is a mixture of Portland cement, fine aggregate, coarse aggregate, and water. This research uses 5 variations of the mixture to the weight of sand, BSA 0 without a substitute mixture, BSA 1 with a mixture of 5% husk ash and 10% shell charcoal, BSA 2 with a mixture of 5% husk ash and 15% charcoal ash, BSA 3 with a mixture of 5% husk ash and 18% charcoal, BSA 4 with a mixture of 10% husk and 10% charcoal, and BSA 5 with a mixture of 13% husk ash and 10% charcoal ash. SNI method is used for the Job Mix Formula (JMF) mixture in this research. The results of the average compressive strength of concrete at 28 days for JMF of 21.05 MPa, BSA 1 of 23.68 MPa, BSA 2 of 22.23 MPa, BSA 3 of 14.39 MPa, BSA 4 of 13.34 MPa , and BSA 5 of 20.14 MPa. The conclusion drawn from the results of the BSA 1 research with a mixture of 5% husk ash and 15% charcoal ash produced the highest average compressive strength of 23.68 MPa. Abstrak Beton merupakan material paling banyak digunakan diseluruh dunia dan terus dilakukan inovasi untuk menghasilkan pembangunan yang efisien. Abu arang tempurung dan abu sekam padi merupakan hasil sampingan industri yang berpotensi sebagai pengganti pasir untuk campuran beton, khususnya di Indragiri Hilir. Penelitian dengan judul “Pengaruh Campuran Abu Sekam Padi dan Abu Arang Tempurung Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton” ini bertujuan membuktikan adanya pengaruh campuran abu arang tempurung dan abu sekam untuk mengganti sebagian pasir hingga menghasilkan kuat tekan maksimum. Beton adalah campuran antara semen portland, agregat halus, agregat kasar, dan air. Penelitian ini menggunakan 5 variasi campuran terhadap berat pasir, BSA 0 tanpa campuran pengganti, BSA 1 dengan campuran 5 % abu sekam dan 10% arang tempurung, BSA 2 dengan campuran 5% abu sekam dan 15% abu arang, BSA 3 dengan campuran 5% abu sekam dan 18% arang, BSA 4 dengan campuran 10% sekam dan 10% arang, dan BSA 5 dengan campuran 13% abu sekam dan 10% abu arang. Metode SNI digunakan untuk campuran Job Mix Formula (JMF)  pada penelitian ini. Hasil rata-rata kuat tekan beton pada umur 28 hari untuk JMF sebesar 21,05 MPa, BSA 1 sebesar 23,68 MPa, BSA 2 sebesar 22,23 MPa, BSA 3 sebesar 14,39 MPa, BSA 4 sebesar 13,34 MPa, dan BSA 5 Sebesar 20,14 MPa. Ditarik kesimpulan dari hasil penelitian BSA 1 dengan campuran 5% abu sekam dan 15% abu arang menghasilkan rata-rata kuat tekan tertinggi yaitu sebesar 23,68 MPa.  

scholarly journals Effects of Disparate Zones of Sand on the Compressive Strength of Concrete

2021 ◽  
Vol 9 (11) ◽  
pp. 1368-1375
Author(s):  
Suhaib Bakshi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Testing Machine ◽  
Concrete Compressive Strength ◽  
Research Papers ◽  
Concrete Material ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Concrete Mix ◽  
Compressive Strength Of Concrete

Abstract: Compressive strength of concrete is the capacity of concrete to bear loads of materials or structure sans breaking or being deformed. Specimen under compression shrinks in size whilst under tension the size elongates. Compressive strength essentially gives concept about the properties of concrete. Compressive strength relies on many aspects such as water-cement ratio, strength of cement, calidad of concrete material. Specimens are tested by compression testing machine after the span of 7 or 28 days of curing. Compressive strength of the concrete is designated by the load on the area of specimen. In this research various proportions of such aggregate mixed in preparing M 30 grade and M 40 grade of Concrete mix and the effect is studied on its compressive strength . Several research papers have been assessed to analyze the compressive strength of concrete and the effect of different zones of sand on compressive strength are discussed in this paper. Keywords: Sand, Gradation, Coarse aggregate, Compressive strength

scholarly journals The influence of different type of aggregate, fly ash and fiber-reinforced polymer on splitting resistance in pretensioned concrete railroad ties

2021 ◽  
Vol 27 (4) ◽  
pp. 135-140
Author(s):  
Adrijana Savić ◽  
Robert Peterman
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Fiber Reinforced Polymer ◽  
Concrete Mixture ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Pretensioned Concrete ◽  
Edge Distance ◽  
Different Types ◽  
Compressive Strength Of Concrete

This research evaluates the influence of the different types of concrete mixture, using a shallow type of indentation of wire, having the different edge distance and compressive strength of concrete on splitting resistance in pretensioned concrete railroad sleepers. The investigated compressive strength of concrete was 4500psi. The research was experimental, and the part of this research was formally adapted in Arema StandardsforRailwayEngineering Chapter 30 section 4.2.4.

Sign in / Sign up

Export Citation Format

Share Document