scholarly journals Use of Transient Time Response as a Measure to Characterize Phononic Crystal Sensors

2018 ◽  
Author(s):  
Simon Villa-Arango ◽  
David Betancur Sánchez ◽  
Róbinson Torres ◽  
Panayiotis Kyriacou
Keyword(s):  
Transient Response ◽  
Composite Structures ◽  
Phononic Crystal ◽  
Defect Mode ◽  
Lithium Carbonate ◽  
Phononic Crystals ◽  
Transient Time ◽  
Frequency Measurements ◽  
Periodic Composite ◽  
The Impact

Phononic crystals are periodic composite structures with specific resonant features that are gaining strength in the field as liquid sensors. The introduction of a structural defect in an otherwise periodic regular arrangement can generate a resonant mode, also called defect mode, inside the characteristic band gaps of phononic crystals. The morphology, as well as the frequency in which these defect modes appear, can give useful information on the composition and properties of an analyte. Currently, only gain, and frequency measurements are performed using phononic crystal sensors. Other measurements like the transient response have been implemented in resonant sensors such as quartz microbalances showing great results and proving to be a great complimentary measure to the gain and frequency measurements. In the present paper, a study of the feasibility of using the transient response as a measure to acquire additional information about the analyte is presented. Theoretical studies using the transmission line model were realized to show the impact of variations in the concentration of an analyte, in this case, lithium carbonate solutions, in the transient time of the system. Experimental realizations were also performed showing that the proposed measurement scheme presents significant changes in the resulting data, indicating the potential use of this measure in phononic crystal sensors. This proposed measure could be implemented as a stand-alone measure or as a compliment to current sensing modalities.

scholarly journals Use of Transient Time Response as a Measure to Characterize Phononic Crystal Sensors

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3618 ◽  
Author(s):  
Simón Villa-Arango ◽  
David Betancur ◽  
Róbinson Torres ◽  
Panayiotis Kyriacou
Keyword(s):  
Transient Response ◽  
Composite Structures ◽  
Phononic Crystal ◽  
Defect Mode ◽  
Lithium Carbonate ◽  
Phononic Crystals ◽  
Transient Time ◽  
Frequency Measurements ◽  
Periodic Composite ◽  
The Impact

Phononic crystals are periodic composite structures with specific resonant features that are gaining popularity in the field as liquid sensors. The introduction of a structural defect in an otherwise periodic regular arrangement can generate a resonant mode, also called defect mode, inside the characteristic band gaps of phononic crystals. The morphology, as well as the frequency in which these defect modes appear, can give useful information on the composition and properties of an analyte. Currently, only gain and frequency measurements are performed using phononic crystal sensors. Other measurements like the transient response have been implemented in resonant sensors such as quartz microbalances showing great results and proving to be a great complimentary measure to the gain and frequency measurements. In the present paper, a study of the feasibility of using the transient response as a measure to acquire additional information about the analyte is presented. Theoretical studies using the transmission line model were realized to show the impact of variations in the concentration of an analyte, in this case, lithium carbonate solutions, in the transient time of the system. Experimental realizations were also performed showing that the proposed measurement scheme presents significant changes in the resulting data, indicating the potential use of this measure in phononic crystal sensors. This proposed measure could be implemented as a stand-alone measure or as a compliment to current sensing modalities.

scholarly journals Design and Optimization of a Novel SAW Gyroscope Structure Based on Amplitude Modulation with 1-D Phononic Crystals

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1485
Author(s):  
Fei Ge ◽  
Liye Zhao ◽  
Yang Zhang
Keyword(s):  
Signal Processing ◽  
Acoustic Wave ◽  
Surface Acoustic Wave ◽  
Amplitude Modulation ◽  
Phononic Crystal ◽  
Defect Mode ◽  
High Sensitivity ◽  
Phononic Crystals ◽  
Linear Range ◽  
One Dimensional

Surface acoustic wave gyroscopes (SAWGs), as a kind of all-solid-state micro-electro-mechanical system (MEMS) gyroscopes, can work normally under extremely high-impact environmental conditions. Among the current SAWGs, amplitude-modulated gyroscopes (AMGs) are all based on the same gyro effect, which was proved weak, and their sensitivity and intensity of the output are both lower than frequency-modulated gyroscopes (FMGs). However, because FMGs need to process a series of frequency signals, their signal processing and circuits are far less straightforward and simple than AMGs. In order to own both high-sensitivity and simple signal processing, a novel surface acoustic traveling wave gyroscope based on amplitude modulation is proposed, using one-dimensional phononic crystals (PCs) in this paper. In view of its specific structure, the proposed gyroscope consists of a surface acoustic wave oscillator and a surface acoustic wave delay line within a one-dimensional phononic crystal with a high-Q defect mode. In this paper, the working principle is analyzed theoretically through the partial wave method (PWM), and the gyroscopes with different numbers of PCs are also designed and studied by using the finite element method (FEM) and multiphysics simulation. The research results demonstrate that under a 1 V oscillator voltage output, the higher sensitivity of −23.1 mV·(rad/s)−1 in the linear range from −8 rad/s to 8 rad/s is reached when the gyro with three PC walls, and the wider linear range from −15 rad/s to 17.5 rad/s with the sensitivity of −6.7 mV·(rad/s)−1 with only one PC wall. Compared with the existing AMGs using metal dots to enhance the gyro effect, the sensitivity of the proposed gyro is increased by 15 to 112 times, and the linear range is increased by 4.6 to 186 times, even without the enhancement of the metal dots.

scholarly journals Tunable graphene phononic crystal

2020 ◽  
Author(s):  
Jan Kirchhof ◽  
Kristina Weinel ◽  
Sebastian Heeg ◽  
Victor Deinhart ◽  
Sviatoslav Kovalchuk ◽  
...  
Keyword(s):  
Phononic Crystal ◽  
Finite Size ◽  
Defect Mode ◽  
Phononic Crystals ◽  
Monolayer Graphene ◽  
Vibrational Modes ◽  
Mechanical Pressure ◽  
Low Dissipation ◽  
Two Dimensional Materials ◽  
Electrostatic Pressure

Abstract In the field of phononics, periodic patterning controls vibrations and thereby the flow of heat and sound in matter. Bandgaps arising in such phononic crystals realize low-dissipation vibrational modes and enable applications towards mechanical qubits, efficient waveguides, and state-of-the-art sensing. Here, we combine phononics and two-dimensional materials and explore the possibility of manipulating phononic crystals via applied mechanical pressure. To this end, we fabricate the thinnest possible phononic crystal from monolayer graphene and simulate its vibrational properties. We find a bandgap in the MHz regime, within which we localize a defect mode with a small effective mass of 0.72 ag = 0.002 mphysical. Finally, we take advantage of graphene’s flexibility and mechanically tune a finite size phononic crystal. Under electrostatic pressure up to 30 kPa, we observe an upshift in frequency of the entire phononic system by more than 350%. At the same time, the defect mode stays within the bandgap and remains localized, suggesting a high-quality, dynamically tunable mechanical system.

Propagation Characteristic in 2D Phononic Crystals with Bending Linear Defect

2012 ◽  
Vol 217-219 ◽  
pp. 2566-2570
Author(s):  
Guang Hui Fan ◽  
De Xun Zhao ◽  
Jiao He ◽  
Ying Kai Liu
Keyword(s):  
Acoustic Wave ◽  
Plane Wave ◽  
Phononic Crystal ◽  
Defect Mode ◽  
Propagation Characteristic ◽  
Phononic Crystals ◽  
Plane Wave Expansion ◽  
Linear Defect ◽  
Plane Wave Method ◽  
The Waves

The band gap of 2D perfect and defect phononic crystal are calculated by using plane-wave expansion (PWE) and supercell plane wave method, which is consist of Al2O3 embedded in the epoxy resin with a square arrangement. Compared to the perfect, the gap of defect will become wider. As the size of defect length ld varied, the band structure changed. It is found that the acoustic wave only propagates along the path of defect when the propagation of acoustic wave is simulated on the 900 bending defect phononic crystals by matlab. It means that the waves are localized. So the defect mode of phononic crystal can be used as acoustic waveguide along the specific path.

Strength Loss in Composite Cylinders Under Impact

1988 ◽  
Vol 110 (2) ◽  
pp. 180-184 ◽  
Author(s):  
A. P. Christoforou ◽  
S. R. Swanson
Keyword(s):  
Composite Structures ◽  
Composite Plates ◽  
Strength Loss ◽  
Pressure Vessels ◽  
Fourier Series Expansion ◽  
Lateral Impact ◽  
Low Velocity ◽  
Expansion Procedure ◽  
The Impact ◽  
Composite Cylinders

The problem of strength loss in composite structures due to impact appears to be important due to the sensitivity of advanced composites to these loadings. Although a number of studies have been carried out on impact of flat composite plates, relatively little work has been done on tubular geometries such as pressure vessels despite the usage in applications. We have addressed the problem of calculating strength loss due to low velocity, lateral impact of composite cylinders. In our model we use an existing Fourier Series expansion procedure to calculate ply stresses and strains, compare these values with allowables to predict fiber breakage during the impact, and finally use fracture mechanics to predict the strength loss due to the impact. Although the model is quite simplified, the general trends of experiments appear to be represented.

Thermal Design of Highly-Efficient Thermoelectric Materials With Atomic-Scale Three-Dimensional Phononic Crystals

2007 ◽  
Author(s):  
Jean-Numa Gillet ◽  
Yann Chalopin ◽  
Sebastian Volz
Keyword(s):  
Thermal Conductivity ◽  
Bulk Material ◽  
Phononic Crystal ◽  
Three Dimensional ◽  
Mean Free Path ◽  
Dispersion Curves ◽  
Phononic Crystals ◽  
Thermal Design ◽  
Atomic Scale ◽  
Thermal Insulating

Owing to their thermal insulating properties, superlattices have been extensively studied. A breakthrough in the performance of thermoelectric devices was achieved by using superlattice materials. The problem of those nanostructured materials is that they mainly affect heat transfer in only one direction. In this paper, the concept of canceling heat conduction in the three spatial directions by using atomic-scale three-dimensional (3D) phononic crystals is explored. A period of our atomic-scale 3D phononic crystal is made up of a large number of diamond-like cells of silicon atoms, which form a square supercell. At the center of each supercell, we substitute a smaller number of Si diamond-like cells by other diamond-like cells, which are composed of germanium atoms. This elementary heterostructure is periodically repeated to form a Si/Ge 3D nanostructure. To obtain different atomic configurations of the phononic crystal, the number of Ge diamond-like cells at the center of each supercell can be varied by substitution of Si diamond-like cells. The dispersion curves of those atomic configurations can be computed by lattice dynamics. With a general equation, the thermal conductivity of our atomic-scale 3D phononic crystal can be derived from the dispersion curves. The thermal conductivity can be reduced by at least one order of magnitude in an atomic-scale 3D phononic crystal compared to a bulk material. This reduction is due to the decrease of the phonon group velocities without taking into account that of the phonon average mean free path.

Acoustic wave frequency filtering in constant total length phononic crystals of Al/Pb multilayer

2021 ◽  
Author(s):  
Chittaranjan Nayak ◽  
Mehdi Solaimani ◽  
Alireza Aghajamali ◽  
Arafa H. Aly
Keyword(s):  
Acoustic Wave ◽  
Phononic Crystal ◽  
Phononic Crystals ◽  
Geometrical Parameters ◽  
One Dimensional ◽  
Internal Geometry ◽  
Total Length ◽  
Acoustic Filters ◽  
System Length ◽  
Phononic Band Gaps

In this study, we have scrutinized the frequency gap generation by changing the geometrical parameters of a one-dimensional phononic crystal. For this purpose, we have calculated the transmission coefficient of an incident acoustic wave by using the transfer matrix method. We have retained and fixed the total length of the system and changed the system internal geometry not to increase the system length too much. Another reason was to adjust the phononic band gaps and get the desired transmission properties by finding the optimum internal geometry without increasing or decreasing the total length of phononic crystals. In addition, we also propose few structures with the opportunity of applications in acoustical devices such as sonic reflectors. Our results can also be of high interest to design acoustic filters in the case that transmission of certain frequencies is necessary.

A General Ply Design for Aero Engine Composite Fan Blade

2017 ◽  
Author(s):  
Jiaguangyi Xiao ◽  
Yong Chen ◽  
Qichen Zhu ◽  
Jun Lee ◽  
Tingting Ma
Keyword(s):  
Composite Laminates ◽  
Composite Structures ◽  
Stacking Sequence ◽  
Composite Blade ◽  
Arduous Task ◽  
Aero Engine ◽  
Margin Of Safety ◽  
Fan Blade ◽  
The Impact ◽  
Ply Orientation

Composite fan blade ply lay-up design, which includes ply drop-off/shuffle design and stacking sequence design, makes fan blade structures different from traditional composite structures. It gives designers more freedom to construct high-quality fan blades. However, contemporary fan blade profiles are quite complex and twisted, and fan blade structures are quite different from regular composite structures such as composite laminates and composite wings. The ply drop-off design of a fan blade, especially for a fully 3D fan blade, is still an arduous task. To meet this challenge, this paper develops a ply lay-up way with the help of a software called Fibersim. The fully 3D fan blade is cut into ply pieces in Fibersim. As a result, an initial ply sequence is created and ply shuffle could revise it. Because of the complexity of ply shuffling, the ply shuffle table developed in this paper mainly refers to the design experience gained from simple plate-like laminate structures and some criterion. Besides, the impact of different ply orientation patterns on the reliability of composite fan blade is studied through static and modal numerical analysis. The results show that this ply lay-up idea is feasible for aero engine composite fan blade. Under the calculated rotating speeds, the ply stacking sequence 4 (i.e.[−45°/0°/+45°/0°] with the outer seven groups are [−45°/0°/−45°/0°]) shows the greatest margin of safety compared with other stacking sequences. Modal analysis shows that plies with different angles could have relatively big different impacts on blades vibration characteristics. The composite fan blade ply design route this paper presents has gain its initial success and the results in this paper might be used as basic references for composite blade initial structural design.

Tunable Band Gaps of Acoustic Waves in Two-Dimensional Phononic Crystals With Reticular Band Structures

2009 ◽  
Author(s):  
Zi-Gui Huang ◽  
Yunn-Lin Hwang ◽  
Pei-Yu Wang ◽  
Yen-Chieh Mao
Keyword(s):  
Acoustic Waves ◽  
Composite Structures ◽  
Phononic Crystals ◽  
Band Gaps ◽  
Sound Insulation ◽  
Two Dimensional ◽  
The Finite Element Method ◽  
Elastic Band ◽  
Band Structures ◽  
Elastic Band Gaps

The excellent applications and researches of so-called photonic crystals raise the exciting researches of phononic crystals. By the analogy between photon and phonon, repetitive composite structures that are made up of different elastic materials can also prevent elastic waves of some certain frequencies from passing by, i.e., the frequency band gap features also exist in acoustic waves. In this paper, we present the results of the tunable band gaps of acoustic waves in two-dimensional phononic crystals with reticular band structures using the finite element method. Band gaps variations of the bulk modes due to different thickness and angles of reticular band structures are calculated and discussed. The results show that the total elastic band gaps for mixed polarization modes can be enlarged or reduced by adjusting the orientation of the reticular band structures. The phenomena of band gaps of elastic or acoustic waves can potentially be utilized for vibration-free, high-precision mechanical systems, and sound insulation.

PIEZOELECTRIC MATERIAL AND ONE-DIMENSIONAL PHONONIC CRYSTAL

2019 ◽  
Vol 26 (02) ◽  
pp. 1850144 ◽  
Author(s):  
ARAFA H. ALY ◽  
AHMED NAGATY ◽  
Z. KHALIFA
Keyword(s):  
Electric Field ◽  
Piezoelectric Material ◽  
Material Properties ◽  
Phononic Crystal ◽  
Defect Layer ◽  
Phononic Crystals ◽  
Localized Modes ◽  
One Dimensional ◽  
Energy Applications ◽  
Relative Change

We have theoretically obtained the transmittance properties of one-dimensional phononic crystals incorporating a piezoelectric material as a defect layer. We have used the transfer matrix method in our analysis with/without defect materials. By increasing the thickness of the defect layer, we obtained a sharp peak created within the bandgap, that indicates to the significance of defect layer thickness on the band structure. The localized modes and a particular intensity estimated within the bandgap depend on the piezoelectric material properties. By applying different quantities of an external electric field, the position of the peak shifts to different frequencies. The electric field induces a relative change in the piezoelectric thickness. Our structure may be very useful in some applications such as sensors, acoustic switches, and energy applications.

Sign in / Sign up

Export Citation Format

Share Document