scholarly journals Comparative Study of Tensile Properties between Fused Filament Fabricated and Injection-Molded Wood-PLA Composite Parts

2020 ◽  
Author(s):  
M. Damous Zandi ◽  
Ramon Jerez-Mesa ◽  
Jordi Llumà ◽  
Jordi Jorba-Peiro ◽  
J. Antonio Travieso-Rodriguez
Keyword(s):  
Tensile Properties ◽  
Wood Fibers ◽  
Fused Filament Fabrication ◽  
Axis Orientation ◽  
Layer Height ◽  
Maximum Tension ◽  
Injection Molded ◽  
Optimal Set ◽  
Printing Parameters ◽  
Manufacturing Parameters

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

scholarly journals Suitability of Recycled PLA Filament Application in Fused Filament Fabrication Process

2021 ◽  
Vol 15 (4) ◽  
pp. 491-497
Author(s):  
Tomislav Breški ◽  
Lukas Hentschel ◽  
Damir Godec ◽  
Ivica Đuretek
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Design Of Experiment ◽  
Experimental Approach ◽  
Manufacturing Processes ◽  
Support Structures ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Printing Parameters

Fused filament fabrication (FFF) is currently one of the most popular additive manufacturing processes due to its simplicity and low running and material costs. Support structures, which are necessary for overhanging surfaces during production, in most cases need to be manually removed and as such, they become waste material. In this paper, experimental approach is utilised in order to assess suitability of recycling support structures into recycled filament for FFF process. Mechanical properties of standardized specimens made from recycled polylactic acid (PLA) filament as well as influence of layer height and infill density on those properties were investigated. Optimal printing parameters for recycled PLA filaments are determined with Design of Experiment methods (DOE).

scholarly journals Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 774 ◽  
Author(s):  
Damir Godec ◽  
Santiago Cano ◽  
Clemens Holzer ◽  
Joamin Gonzalez-Gutierrez
Keyword(s):  
Stainless Steel ◽  
3D Printing ◽  
Tensile Properties ◽  
Layer Thickness ◽  
Flow Rate ◽  
Three Dimensional ◽  
Steel Powder ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Printing Parameters

Fused filament fabrication (FFF) combined with debinding and sintering could be an economical process for three-dimensional (3D) printing of metal parts. In this paper, compounding, filament making, and FFF processing of feedstock material with 55% vol. of 17-4PH stainless steel powder in a multicomponent binder system are presented. The experimental part of the paper encompasses central composite design for optimization of the most significant 3D printing parameters (extrusion temperature, flow rate multiplier, and layer thickness) to obtain maximum tensile strength of the 3D-printed specimens. Here, only green specimens were examined in order to be able to determine the optimal parameters for 3D printing. The results show that the factor with the biggest influence on the tensile properties was flow rate multiplier, followed by the layer thickness and finally the extrusion temperature. Maximizing all three parameters led to the highest tensile properties of the green parts.

scholarly journals Mechanical Properties of 3D-Printing Polylactic Acid Parts subjected to Bending Stress and Fatigue Testing

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3859 ◽  
Author(s):  
J. Antonio Travieso-Rodriguez ◽  
Ramon Jerez-Mesa ◽  
Jordi Llumà ◽  
Oriol Traver-Ramos ◽  
Giovanni Gomez-Gras ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fatigue Testing ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Four Point Bending ◽  
Layer Orientation ◽  
Rotating Bending ◽  
Flexural Resistance ◽  
Optimal Set

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries were tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance was determined. The results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with that of previous studies’ results, in order to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

scholarly journals Mechanical Properties of 3D-Printing Polylactic Acid Parts Subjected to Bending Stress and Fatigue Testing

2019 ◽  
Author(s):  
J. Antonio Travieso-Rodriguez ◽  
Ramon Jerez-Mesa ◽  
Jordi Llumà ◽  
Oriol Traver-Ramos ◽  
Giovanni Gomez-Gras ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fatigue Testing ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Four Point Bending ◽  
Layer Orientation ◽  
Rotating Bending ◽  
Flexural Resistance ◽  
Optimal Set

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

Evaluation of the printing strategies design on the mechanical and tribological response of acrylonitrile styrene acrylate (ASA) additive manufacturing parts

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Juan Manuel Vázquez Martínez ◽  
David Piñero Vega ◽  
Jorge Salguero ◽  
Moises Batista
Keyword(s):  
Additive Manufacturing ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Mechanical Behavior ◽  
Layer Thickness ◽  
Fused Filament Fabrication ◽  
Friction Forces ◽  
Content Type ◽  
Printing Parameters ◽  
Manufacturing Parameters

Purpose The evaluation of novel materials such as the acrylonitrile styrene acrylate (ASA) for tribological and mechanical conditions can provide a structural protection against the environmental and wear effects that results in the long-term integrity of the 3 D printed parts. Results of the experimental stage are intended to identify the influence of the printing conditions on the functional characteristics of ASA parts that results in variations of the friction coefficient, wear rate and tensile response. In addition, this study aims to highlight the relevance of printing parameters to avoid the use of chemical post-processing stages, increasing the performance and sustainability of the process. Design/methodology/approach In this research, an evaluation of the influence of printing parameters of layer thickness and temperature on the mechanical and tribological response have been carried out for ASA specimens manufactured by fused filament fabrication technology. For this purpose, a range of three different values of thickness of fused layer and three different printing temperatures were combined in the manufacturing process of tests samples. Mechanical behavior of the printed parts was evaluated by standard tensile tests, and friction forces were measured by pin-on-disk tribological tests against steel spheres. Findings Higher layer thickness of the printed parts shows lower resistance to tribological wear effects; in terms of friction coefficient and wear rate, this type of parts also presents lower tensile strength. It has been detected that mechanical and tribological behavior is highly related to the micro-geometrical characteristics of the printed surfaces, which can be controlled by the manufacturing parameters. Under this consideration, a reduction in the coefficient of friction near to 65% in the average value was obtained through the variation of the layer thickness of printed surfaces. Originality/value This research aims to fill a gap in the scientific literature about the use of specific additive manufacturing materials under dynamic contact. This paper is mainly focused on the influence of the manufacturing parameters on the tribological and mechanical behavior of a weather resistant polymer (ASA).

scholarly journals Improving Tensile Properties of Polylactic Acid Parts by Adjusting Printing Parameters of Open Source 3D Printers

2019 ◽  
Vol 26 (1) ◽  
pp. 83-87 ◽  
Author(s):  
Yubo TAO ◽  
Peng LI ◽  
Ling PAN
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Open Source ◽  
Tensile Properties ◽  
Polylactic Acid ◽  
Elongation At Break ◽  
Layer Height ◽  
Fused Deposition ◽  
3D Printers ◽  
Printing Parameters

Open source 3D printers (OS3DPs) have become increasingly more widespread in recent years because of their ease of use and budget friendliness, with the majority being fused deposition modeling (FDM) printers. However, due to natural deficiencies of the FDM printing methodology, different printing parameters can cause various properties of printed parts. To obtain printed polylactic acid (PLA) parts with improved tensile properties, a tension model of the part and an orthogonal experiment scheme were constructed in this paper. The effects of three printing parameters (layer height, orientation angle (OA) of the part, and print speed) on tensile properties (elastic modulus, tensile strength, and elongation at break) were investigated. The results demonstrated that the printing parameters affected the tensile properties of PLA parts. Larger layer height and lower print speed contributed to the improvement of tensile strength. The OA of the part had the greatest effect on the parts’ elastic modulus and elongation at break among the three parameters. Both layer height and OA of the part affected part tensile strength significantly. In this research, layer height of 0.2 mm and print speed of 20 ~ 30 mm/s are found to be the optimal printing parameters. Adjusting the OA of the part can provide targeted tensile properties, and the parts with the OA of 45° resulted in the lowest tensile strength because the tensile force is only held by fibers parallel to the force orientation instead of all fibers.

scholarly journals Effect of Printing Parameters on Dimensional Error, Surface Roughness and Porosity of FFF Printed Parts with Grid Structure

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1213
Author(s):  
Irene Buj-Corral ◽  
Ali Bagheri ◽  
Maurici Sivatte-Adroer
Keyword(s):  
Flow Rate ◽  
Desirability Function ◽  
Low Cost ◽  
Multi Objective Optimization ◽  
Grid Structure ◽  
Fused Filament Fabrication ◽  
Dimensional Error ◽  
Layer Height ◽  
Multi Objective ◽  
Printing Parameters

Extrusion printing processes allow for manufacturing complex shapes in a relatively cheap way with low-cost machines. The present study analyzes the effect of printing parameters on dimensional error, roughness, and porosity of printed PLA parts obtained with grid structure. Parts are obtained by means of the fused filament fabrication (FFF) process. Four variables are chosen: Layer height, temperature, speed, and flow rate. A two-level full factorial design with a central point is used to define the experimental tests. Dimensional error and porosity are measured with a profile projector, while roughness is measured with a contact roughness meter. Mathematical regression models are found for each response, and multi-objective optimization is carried out by means of the desirability function. Dimensional error and roughness depend mainly on layer height and flow rate, while porosity depends on layer height and printing speed. Multi-objective optimization shows that recommended values for the variables are layer height 0.05 mm, temperature 195 ºC, speed 50 mm/min, and flow rate 0.93, when dimensional error and roughness are to be minimized, and porosity requires a target value of 60%. The present study will help to select appropriate printing parameters for printing porous structures such as those found in prostheses, by means of extrusion processes.

scholarly journals Design of Shape Memory Thermoplastic Material Systems for FDM-Type Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4254
Author(s):  
Paulina A. Quiñonez ◽  
Leticia Ugarte-Sanchez ◽  
Diego Bermudez ◽  
Paulina Chinolla ◽  
Rhyan Dueck ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Shape Memory ◽  
Thermomechanical Processing ◽  
Material Selection ◽  
Shape Memory Polymer ◽  
Fused Filament Fabrication ◽  
Materials Development ◽  
Thermoplastic Material ◽  
Polymer Systems ◽  
Injection Molded

The work presented here describes a paradigm for the design of materials for additive manufacturing platforms based on taking advantage of unique physical properties imparted upon the material by the fabrication process. We sought to further investigate past work with binary shape memory polymer blends, which indicated that phase texturization caused by the fused filament fabrication (FFF) process enhanced shape memory properties. In this work, two multi-constituent shape memory polymer systems were developed where the miscibility parameter was the guide in material selection. A comparison with injection molded specimens was also carried out to further investigate the ability of the FFF process to enable enhanced shape memory characteristics as compared to other manufacturing methods. It was found that blend combinations with more closely matching miscibility parameters were more apt at yielding reliable shape memory polymer systems. However, when miscibility parameters differed, a pathway towards the creation of shape memory polymer systems capable of maintaining more than one temporary shape at a time was potentially realized. Additional aspects related to impact modifying of rigid thermoplastics as well as thermomechanical processing on induced crystallinity are also explored. Overall, this work serves as another example in the advancement of additive manufacturing via materials development.

scholarly journals Fatigue Performance of ABS Specimens Obtained by Fused Filament Fabrication

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2521 ◽  
Author(s):  
Miquel Domingo-Espin ◽  
J. Antonio Travieso-Rodriguez ◽  
Ramon Jerez-Mesa ◽  
Jordi Lluma-Fuentes
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Experimental Phase ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Bending Stresses ◽  
Best Parameter ◽  
End Use ◽  
Design And Manufacture ◽  
Printing Speed ◽  
Butadiene Styrene

In this paper, the fatigue response of fused filament fabrication (FFF) Acrylonitrile butadiene styrene (ABS) parts is studied. Different building parameters (layer height, nozzle diameter, infill density, and printing speed) were chosen to study their influence on the lifespan of cylindrical specimens according to a design of experiments (DOE) using the Taguchi methodology. The same DOE was applied on two different specimen sets using two different infill patterns—rectilinear and honeycomb. The results show that the infill density is the most important parameter for both of the studied patterns. The specimens manufactured with the honeycomb pattern show longer lifespans. The best parameter set associated to that infill was chosen for a second experimental phase, in which the specimens were tested under different maximum bending stresses so as to construct the Wöhler curve associated with this 3D printing configuration. The results of this study are useful to design and manufacture ABS end-use parts that are expected to work under oscillating periodic loads.

Sign in / Sign up

Export Citation Format

Share Document