Evaluation of: MOSSA, MOALO, MOVO and MOGWO Algorithms in Green Machining for High Production Performance in Turning of X210Cr12 Steel

2021 ◽  
Author(s):  
Mourad NOUIOUA ◽  
Aissa LAOUISSI ◽  
Mohamed Mossaab BLAOUI ◽  
Abderzzak HAMMOUDI ◽  
Mohamed Athmane YALLESE
Keyword(s):  
Tangential Force ◽  
Cutting Parameters ◽  
Production Performance ◽  
Tool Geometry ◽  
Nose Radius ◽  
Environment Friendly ◽  
Part Quality ◽  
Output Factors ◽  
High Production ◽  
Coated Carbide

Abstract The current study investigates the Wet and MQL machining, when turning of X210Cr12 steel, using a multilayer-coated carbide insert (GC-4215) with various nose radius, the consideration of the tool geometry with different cooling modes allow as to assess the comportment of the machined steel against the cutting combinations. The response surface methodology (RSM) has been used for regression analysis and to evaluate the contribution of the cutting parameters on surface roughness, tangential force and cutting power using ANOVA analysis. The developed models have been used to predict the studied output factors according to the selected cutting parameters for wet and MQL machining. A comparative between the cooling techniques have been established to determine the most effective technique in terms of part quality, lubricant consumption and power consumption. Finally, four new optimization technics have been used for the process optimization using the MQL models for an environment-friendly machining.

Effects of Cutting Parameters on Chip Side-Curl Mechanisms and Variable Tool-Chip Contact in Turning

1999 ◽  
Author(s):  
A. K. Balaji ◽  
I. S. Jawahir
Keyword(s):  
High Speed ◽  
Cutting Parameters ◽  
Sem Analysis ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Turning Operations ◽  
Variable Friction ◽  
On Chip ◽  
Bar Turning

Abstract This paper presents the results of an investigative study on the chip side-curling mechanism and the associated variable tool-chip contact in turning operations. The effect of various cutting and tool geometry parameters such as depth of cut-nose radius ratio, feed, inclination angle, etc. on chip side-curling are established in a hierarchical manner. The importance of variable friction at the tool-chip interface along the developed length of the cutting edge is shown from the experimental observations of the tool-chip contact area using a SEM analysis. The significant influence of the radial cutting force component on the resultant chip side-curl is established using a high speed-filming analysis of comparative experiments in tube and bar turning operations.

scholarly journals The Outcome of Turning Factors on the Machining Characteristics While Turning 655M13 Steel Alloy using Tialn Coated Carbide Insert

2020 ◽  
Vol 9 (3) ◽  
pp. 1251-1260 ◽  
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Prediction Models ◽  
Tangential Force ◽  
Interface Temperature ◽  
Depth Of Cut ◽  
Steel Alloy ◽  
Nose Radius ◽  
Feed Force ◽  
Coated Carbide

This exploration is carried out to reveal the outcome of turning factors such as cutting velocity, depth of cut and feed rate on the surface roughness, mean cutting force and tool-work interface temperature on turning cylindrical 655M13 steel alloy components. The experiments are designed based on (33) full factorial design and conducted on a turning centre with Titanium Aluminium Nitride (TiAlN) layered carbide tool of 0.8mm nose radius, simultaneously cutting forces such as feed force, thrust force and tangential force and the tool-work interface temperature are observed using calibrated devices. The surface roughness of the turned steel alloy parts is deliberated by means of a precise surface roughness apparatus. Prediction models are created for average surface roughness, mean cutting force and tool-work interface temperature by nonlinear regression examination with the aid of MINITAB numerical software. The optimum machining conditions are confirmed with the aid of a Genetic Algorithm. The outcome of each turning factor on the surface roughness, mean cutting force and tool-work interface temperature is studied and presented accordingly.

scholarly journals Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3993
Author(s):  
Thanh Trung Do ◽  
Pham Son Minh ◽  
Nhan Le
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Side Wall ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Experimental Investigation on Surface Roughness in Precision Cutting Ti6Al4V Alloy Using Diamond Tools

2014 ◽  
Vol 800-801 ◽  
pp. 576-579
Author(s):  
Lin Hua Hu ◽  
Ming Zhou ◽  
Yu Liang Zhang
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Cutting Parameters ◽  
Limited Range ◽  
Nose Radius ◽  
Machined Surface ◽  
Machined Surface Roughness ◽  
Titanium Alloy Ti6al4v ◽  
Pcd Tools

In this work, cutting experiments were carried out on titanium alloy Ti6Al4V by using polycrystalline diamond (PCD) tools to investigate the effects of the tool geometries and cutting parameters on machined surface roughness. Experimental results show machined surface roughness decreases with increases in the flank angle, tool nose radius and cutting speed within a limited range respectively, and begins to increase as the factors reaches to certain values respectively. And machined surface roughness decreases with increases in feed rate and cutting depth respectively.

Monitoring of Cutting Conditions with Dry Cutting on CNC Turning Machine

2010 ◽  
Vol 443 ◽  
pp. 382-387 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Suthas Ratanakuakangwan
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Temperature ◽  
Cutting Conditions ◽  
Cutting Condition ◽  
Nose Radius ◽  
Dry Cutting ◽  
Cnc Turning ◽  
Coated Carbide

This paper presents the additional work of the previous research in order to verify the previously obtained cutting condition by using the different cutting tool geometries. The effects of the cutting conditions with the dry cutting are monitored to obtain the proper cutting condition for the plain carbon steel with the coated carbide tool based on the consideration of the surface roughness and the tool life. The dynamometer is employed and installed on the turret of CNC turning machine to measure the in-process cutting forces. The in-process cutting forces are used to analyze the cutting temperature, the tool wear and the surface roughness. The experimentally obtained results show that the surface roughness and the tool wear can be well explained by the in-process cutting forces. Referring to the criteria, the experimentally obtained proper cutting condition is the same with the previous research except the rake angle and the tool nose radius.

Experimental investigation of the influence of cutting parameters on surface quality and on the special characteristics of micro-milled surfaces of hardened steels

2021 ◽  
pp. 095440622110130
Author(s):  
Barnabás Zoltán Balázs ◽  
Márton Takács
Keyword(s):  
Surface Quality ◽  
Surface Profile ◽  
Cutting Parameters ◽  
Relevant Information ◽  
Milling Process ◽  
Micro Milling ◽  
Machined Surface ◽  
Analysis Of Dynamics ◽  
Five Axis ◽  
Coated Carbide

Micro-milling is one of the most essential technologies to produce micro components, but due to the size effect, it has many special characteristics and challenges. The process can be characterised by strong vibrations, relatively large run-out and tool deformation, which directly affects the quality of the machined surface. This paper deals with a detailed investigation of the influence of cutting parameters on surface roughness and on the special characteristics of micro-milled surfaces. Several systematic series of experiments were carried out and analysed in detail. A five-axis micromachining centre and a two fluted, coated carbide micro-milling tool with a diameter of 500 µm were used for the tests. The experiments were conducted on AISI H13 hot-work tool steel and Böhler M303 martensitic corrosion resistance steel with a hardness of 50 HRC in order to gain relevant information of machining characteristics of potential materials of micro-injection moulding tools. The effect of the cutting parameters on the surface quality and on the ratio of Rz/ Ra was investigated in a comprehensive cutting parameter range. ANOVA was used for the statistical evaluation. A novel method is presented, which allows a detailed analysis of the surface profile and repetitions, and identify the frequencies that create the characteristic profile of the surface. The procedure establishes a connection between the frequencies obtained during the analysis of dynamics (forces, vibrations) of the micro-milling process and the characterising repetitions and frequencies of the surface.

Optimisation of Springback Predicted by Experimental and Numerical Approach by Using Response Surface Methodology

2005 ◽  
Vol 6-8 ◽  
pp. 753-762
Author(s):  
R. Bahloul ◽  
Phillippe dal Santo ◽  
Ali Mkaddem ◽  
A. Potiron
Keyword(s):  
Response Surface ◽  
Sheet Metal ◽  
Design Method ◽  
Fem Simulation ◽  
Numerical Approach ◽  
Tool Geometry ◽  
Nose Radius ◽  
Element Analysis ◽  
Metal Parts ◽  
Sheet Metal Parts

Bending has significant importance in the sheet metal product industry. Moreover, the springback of sheet metal should be taken into consideration in order to produce bent sheet metal parts within acceptable tolerance limits and to solve geometrical variation for the control of manufacturing process. Nowadays, the importance of this problem increases because of the use of sheet-metal parts with high mechanical characteristics (High Strength Low Alloy steel). This work describes robust methods of predicting springback of parts in 3D modelling subjected to bending and unbending deformations. Also the effects of tool geometry in the final shape after springback are discussed. The first part of this paper presents the laboratory experiments in wiping die bending, in which the influence of process variables, such as die shoulder radius, punch-die clearance, punch nose radius and materials properties were discussed. The second part summarises the finite element analysis by using ABAQUS software and compares these results with some experimental data. It appeared that the final results of the FEM simulation are in good agreement with the experimental ones. An optimisation methodology based on the use of experimental design method and response surface technique is proposed in the third part of this paper. That makes it possible to obtain the optimum values of clearance between the punch and the die and the optimum die radius which can reduce the springback without cracking and damage of product.

Sign in / Sign up

Export Citation Format

Share Document