scholarly journals Bimetallic Fe/Al-MOF for the Adsorptive Removal of Multiple Dyes: Optimization and Modeling of Batch and Hybrid Adsorbent-river Sand Column Study

2021 ◽  
Author(s):  
Hemant Singh ◽  
Sankalp Raj ◽  
Rishi karan singh rathour ◽  
Jayanta Bhattacharya
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Fixed Bed ◽  
Maximum Adsorption Capacity ◽  
Feed Concentration ◽  
River Sand ◽  
Fixed Bed Column ◽  
Column Study ◽  
Adsorptive Removal ◽  
Bed Height

Abstract Bimetallic Metal organic framework (MOF) has garnered interest over the years with its application in various environmental remediation. In this study, Fe-Al-1,4-Benzene di-Carboxylic acid (FeAl(BDC)) MOF was synthesized, and adsorptive removal of Rhodamine B dye in batch and unique hybrid FeAl (BDC)-River sand fixed-bed column was achieved. The experimental data from the batch studies corroborated well with the Pseudo second-order (PSO) and Freundlich adsorption isotherm models. Furthermore, a fixed-bed column study was conducted to assess the effect of varying flow rate (2, 5, 8 mL/min), bed height (5, 9, 13 cm), and feed concentration (10, 20, 30 mg/L) on the adsorption performance of FeAl(BDC) in continuous mode of operation. A uniform mixture of river sand and FeAl(BDC) by weight ratio (9:1) was achieved prior to packing the column. The column study reveals that Sand-FeAl(BDC) can achieve the maximum adsorption capacity of 113.05 mg/g at a flow rate of 5 mL/min, feed concentration of 20 mg/L, and bed height of 13 cm. The experimental data of the column study were successfully fitted with BDST, Thomas, Yoon-Nelson, and Dose-response models. The fitting parameter values from the BDST model raise the scope of possible upscaling of the fixed-bed column. Hence, it is proposed that these River sand-FeAl(BDC)-based filters can be widely used in areas facing critical contamination and in poor communities with a high demand for water.

scholarly journals FIXED-BED ADSORPTION OF AQUEOUS VANILLIN ONTO RESIN H103

2017 ◽  
Vol 18 (2) ◽  
pp. 94-104
Author(s):  
Rozaimi Abu Samah
Keyword(s):  
Aqueous Solution ◽  
Flow Rate ◽  
Adsorption Process ◽  
Fixed Bed ◽  
Maximum Adsorption Capacity ◽  
Feed Flow Rate ◽  
Fixed Bed Column ◽  
Initial Concentration ◽  
Bed Height ◽  
Fixed Bed Adsorption

The main objective of this work was to design and model fixed bed adsorption column for the adsorption of vanillin from aqueous solution. Three parameters were evaluated for identifying the performance of vanillin adsorption in fixed-bed mode, which were bed height, vanillin initial concentration, and feed flow rate. The maximum adsorption capacity was increased more than threefold to 314.96 mg vanillin/g resin when the bed height was increased from 5 cm to 15 cm. Bohart-Adams model and Belter equation were used for designing fixed-bed column and predicting the performance of the adsorption process. A high value of determination coefficient (R2) of 0.9672 was obtained for the modelling of vanillin adsorption onto resin H103.

Removal of Cesium from Aqueous Solution Using PAN-Based Ferrocyanide Composite Spheres: Adsorption on a Fixed-Bed Column

2014 ◽  
Vol 496-500 ◽  
pp. 259-263 ◽  
Author(s):  
Zhi Hui Du ◽  
Ming Chun Jia ◽  
Jin Feng Men
Keyword(s):  
Flow Rate ◽  
Fixed Bed ◽  
Breakthrough Curves ◽  
Model Parameters ◽  
Maximum Adsorption Capacity ◽  
Fixed Bed Column ◽  
Composite Adsorbents ◽  
Bed Height ◽  
Cobalt Hexacyanoferrates ◽  
Good Agreement

Two spherical composite adsorbents namely polyacrylonitrilepotassium cobalt hexacyanoferrates (PAN-KCoCF) and polyacrylonitrilepotassium nickel hexacyanoferrates (PAN-KNiCF) were synthesized. The effects of liquid flow rate, bed height and presence of other cations on the adsorption of cesium were investigated by conducting fixed-bed columns. The results showed that the column performed well at lowest flow rate for PAN-KNiCF. Flow rate examined had little influence on the adsorption of PAN-KCoCF. The breakthrough time decreased with decreasing bed height for both PAN-KCoCF and PAN-KNiCF. In addition, the existence of K+, Na+, NH4+, Ca2+and Mg2+in solution caused a reduction of maximum adsorption capacity for both of the composites. The bed depth service time (BDST) model and the Thomas model were used to analyze the experimental data and the model parameters were evaluated. Good agreement of the experimental breakthrough curves with the model predictions was observed.

Modeling of breakthrough curves for aqueous iron (III) adsorption on chitosan-sodium tripolyphosphate

2016 ◽  
Vol 74 (10) ◽  
pp. 2297-2304 ◽  
Author(s):  
Dalia I. Sánchez-Machado ◽  
Jaime López-Cervantes ◽  
Ma. A. Correa-Murrieta ◽  
Reyna G. Sánchez-Duarte
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Adsorption Process ◽  
Sodium Tripolyphosphate ◽  
Fixed Bed ◽  
Breakthrough Curves ◽  
Operating Conditions ◽  
Feed Concentration ◽  
Fixed Bed Column ◽  
Continuous Adsorption

A fixed bed column packed with chitosan-sodium tripolyphosphate (CTPP) beads was used to remove aqueous Fe (III) ions. The adsorption of Fe (III) ions on CTPP beads was found to be dependent on operating conditions, such as the flow rate, adsorbent bed length, and feed concentration. The experimental data were assessed with Thomas, Adams-Bohart and Yoon-Nelson models to predict the breakthrough curves using linear regression. The breakthrough curves were better fitted with the Thomas and Yoon-Nelson models when the flow rate was varied and the feed concentration and the bed height of the column were fixed. Therefore, chemical adsorption may be the limiting step that controls the continuous adsorption process. The Adams-Bohart model presented a good fit to the experimental data, showing that external mass transfer was controlling the adsorption process in the initial part of the breakthrough curves. The parameters obtained from the continuous adsorption assays may be used as a basis for designing columns packed with CTPP beads for the removal of Fe (III) ions.

scholarly journals FIXED-BED COLUMN ADSORPTION OF FLUOROQUINOLONE ANTIBIOTIC FROM AQUEOUS SOLUTION ONTO SUGARCANE BAGASSE BIOCHAR

2020 ◽  
Vol 58 (3A) ◽  
pp. 93
Author(s):  
Linh Thuy Nguyen ◽  
Thuy Thi Pham ◽  
Hanh Thi Nguyen ◽  
Hoai Thu Dang ◽  
Khai Manh Nguyen ◽  
...  
Keyword(s):  
Sugarcane Bagasse ◽  
Flow Rate ◽  
Fixed Bed ◽  
Column Experiment ◽  
Maximum Adsorption Capacity ◽  
Fixed Bed Column ◽  
Initial Concentration ◽  
Bed Height ◽  
Column Adsorption ◽  
Fluoroquinolone Antibiotic

The ability of the agricultural residue of sugarcane bagasse to serve as an absorbent material used to remove Ciprofloxacin, one of strong Fluoroquinolone antibiotic from aqueous solutions in fixed-bed columns was investigated. The properties of biochar sugarcane bagasse were characterized using scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy before and after modification. The results of fixed bed column experiment showed that the shape of the removal efficiency of CIP and exhaustion time was dependent on bed height, flow rate and initial concentration. The maximum adsorption capacity qo predicted from Thomas modelreached 0.955mg/g at the flow rate of 1mL/min, initial concentration of 15mg/L and bed height of 6cm. From Yoon-Nelson equation, 3.38 minutes was the time required for 50% exhaustion of 12cm bed height column with the flow rate 2mL/min and concentration 15mg/L. Thomas and Yoon-Nelson models were in good agreement with the experimental breakthrough curve data.

Biochar caged zirconium ferrite nanocomposites for the adsorptive removal of Reactive Blue 19 dye in a batch and column reactors and conditions optimizaton

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Shazia Perveen ◽  
Raziya Nadeem ◽  
Shaukat Ali ◽  
Yasir Jamil
Keyword(s):  
Experimental Data ◽  
Low Dose ◽  
Fixed Bed ◽  
Breakthrough Curves ◽  
Adsorption Efficiency ◽  
Fixed Bed Column ◽  
Flow Rates ◽  
Adsorptive Removal ◽  
Reactive Blue 19 ◽  
Pseudo Second Order

Abstract Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.

scholarly journals Sorption of Ag+ and Cu2+ by Vermiculite in a Fixed-Bed Column: Design, Process Optimization and Dynamics Investigations

2018 ◽  
Vol 8 (11) ◽  
pp. 2221 ◽  
Author(s):  
Olga Długosz ◽  
Marcin Banach
Keyword(s):  
Flow Rate ◽  
Continuous Process ◽  
Fixed Bed ◽  
Copper Ion ◽  
Cost Effective ◽  
Breakthrough Curves ◽  
Fixed Bed Column ◽  
Column System ◽  
Total Percentage ◽  
Bed Height

Vermiculite has been used for the removal of Cu 2 + and Ag + from aqueous solutions in a fixed-bed column system. The effects of initial silver and copper ion concentrations, flow rate, and bed height of the adsorbent in a fixed-bed column system were investigated. Statistical analysis confirmed that breakthrough curves depended on all three factors. The highest inlet metal cation concentration (5000 mg/dm3), the lowest bed height (3 cm) and the lowest flow rate (2 and 3 cm3/min for Ag + and Cu 2 + , respectively) were optimal for the adsorption process. The maximum total percentage of metal ions removed was 60.4% and 68.7% for Ag+ and Cu2+, respectively. Adsorption data were fitted with four fixed-bed adsorption models, namely Clark, Bohart–Adams, Yoon–Nelson and Thomas models, to predict breakthrough curves and to determine the characteristic column parameters. The adsorbent was characterized by SEM, FTIR, EDS and BET techniques. The results showed that vermiculite could be applied as a cost-effective sorbent for the removal of Cu 2 + and Ag + from wastewater in a continuous process.

Zinc(II) desorption by Sargassum filipendula biomass in batch and in fixed-bed column for multiple sorption-regeneration cycles

2009 ◽  
Vol 60 (2) ◽  
pp. 357-362 ◽  
Author(s):  
Araceli A. Seolatto ◽  
Maurício M. Câmara ◽  
Eneida S. Cossich ◽  
Célia R. G. Tavares ◽  
Edson A. Silva
Keyword(s):  
Adsorption Capacity ◽  
Flow Rate ◽  
Batch Reactor ◽  
Fixed Bed ◽  
Feed Concentration ◽  
Fixed Bed Column ◽  
Batch System ◽  
High Efficient ◽  
Sargassum Filipendula

The reusability of the alga Sargassum filipendula was studied in batch reactor and in fixed-bed column in order to investigate Zn(II)-laden biomass regeneration. Four types of desorbing solutions at two different concentrations were tested and the results obtained to the desorption efficiencies were higher than 90% for three of the agents. Ten consecutive sorption-regeneration cycles at a flow rate of 8 mL/min were carried in fixed bed column with the feed concentration of 50 mg/L and using two eluent solutions: H2SO4 (0.1 M) and MgSO4 (3.5% at pH 3), which showed the best ability to elution tests in batch system. The column was used for a period of 30 days. The adsorption capacity decreased the passing of cycles, but the total amount of zinc removed after 10 cycles was approximately 8 times greater than if the biomass had been used for only one time, for both agents tested. Therefore, the regeneration in the Sargassum filipendula column through the two desorbing agents tested showing high efficient use of biomass and facilitating the process of treatment of wastewater containing metals that has successive exchanges of biomass.

scholarly journals Study of a fixed-bed column in the adsorption of an azo dye from an aqueous medium using a chitosan–glutaraldehyde biosorbent

2017 ◽  
Vol 36 (1-2) ◽  
pp. 215-232 ◽  
Author(s):  
Jaime López-Cervantes ◽  
Dalia I Sánchez-Machado ◽  
Reyna G Sánchez-Duarte ◽  
Ma A Correa-Murrieta
Keyword(s):  
Flow Rate ◽  
Service Time ◽  
Fixed Bed ◽  
Textile Dye ◽  
Time Model ◽  
Fixed Bed Column ◽  
Bed Height ◽  
Direct Blue ◽  
Direct Blue 71 ◽  
Bed Depth Service Time

A continuous adsorption study in a fixed-bed column was carried out using a chitosan–glutaraldehyde biosorbent for the removal of the textile dye Direct Blue 71 from an aqueous solution. The biosorbent was prepared from shrimp shells and characterized by scanning electron microscopy, X-ray diffraction, and nuclear magnetic resonance spectroscopy. The effects of chitosan–glutaraldehyde bed height (3–12 cm), inlet Direct Blue 71 concentration (15–50 mg l−1), and feed flow rate (1–3 ml min−1) on the column performance were analyzed. The highest bed capacity of 343.59 mg Direct Blue 71 per gram of chitosan–glutaraldehyde adsorbent was obtained using 1 ml min−1 flow rate, 50 mg l−1 inlet Direct Blue 71 concentration, and 3 cm bed height. The breakthrough curve was analyzed using the Adams–Bohart, Thomas, and bed depth service time mathematical models. The behaviors of the breakthrough curves were defined by the Thomas model at different conditions. The bed depth service time model showed good agreement with the experimental data, and the high values of correlation coefficients (R2 ≥ 0.9646) obtained indicate the validity of the bed depth service time model for the present column system.

scholarly journals Adsorption of Sb(III) from Aqueous Solution by nZVI/AC: A Magnetic Fixed-Bed Column Study

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1912
Author(s):  
Huijie Zhu ◽  
Qiang Huang ◽  
Mingyan Shi ◽  
Shuai Fu ◽  
Xiuji Zhang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Fixed Bed ◽  
Feed Solution ◽  
Breakthrough Curves ◽  
Contaminated Water ◽  
Solution Ph ◽  
Fixed Bed Column ◽  
Ph Values ◽  
Bed Height ◽  
Bed Capacity

The effectiveness of nanoscale zero-valent iron(nZVI) immobilized on activated carbon (nZVI/AC) in removing antimonite (Sb(III)) from simulated contaminated water was investigated with and without a magnetic fix-bed column reactor. The experiments were all conducted in fixed-bed columns. A weak magnetic field (WMF) was proposed to increase the exclusion of paramagnetic Sb(III) ions by nZVI/AC. The Sb(III) adsorption to the nZVI and AC surfaces, as well as the transformation of Sb(III) to Sb(V) by them, were both increased by using a WMF in nZVI/AC. The increased sequestration of Sb(III) by nZVI/AC in the presence of WMF was followed by faster nZVI corrosion and dissolution. Experiments were conducted as a function of the pH of the feed solution (pH 5.0–9.0), liquid flow rate (5–15 mL·min−1), starting Sb(III) concentration (0.5–1.5 mg·L−1), bed height nZVI/AC (10–40 cm), and starting Sb(III) concentration (0.5–1.5 mg·L−1). By analyzing the breakthrough curves generated by different flow rates, different pH values, different inlet Sb(III) concentrations, and different bed heights, the adsorbed amounts, equilibrium nZVI uptakes, and total Sb(III) removal percentage were calculated in relation to effluent volumes. At pH 5.0, the longest nZVI breakthrough time and maximal Sb(III) adsorption were achieved. The findings revealed that the column performed effectively at the lowest flow rate. With increasing bed height, column bed capacity and exhaustion time increased as well. Increasing the Sb(III) initial concentration from 0.5 to 1.5 mg·L−1 resulted in the rise of adsorption bed capacity from 3.45 to 6.33 mg·g−1.

Continuous fixed bed adsorption of Cu(II) by halloysite nanotube–alginate hybrid beads: an experimental and modelling study

2014 ◽  
Vol 70 (2) ◽  
pp. 192-199 ◽  
Author(s):  
Yanyan Wang ◽  
Xiang Zhang ◽  
Qiuru Wang ◽  
Bing Zhang ◽  
Jindun Liu
Keyword(s):  
Adsorption Capacity ◽  
Flow Rate ◽  
Fixed Bed ◽  
Halloysite Nanotubes ◽  
Fixed Bed Column ◽  
Factors Affecting ◽  
Bed Height ◽  
Column Adsorption ◽  
Fixed Bed Adsorption ◽  
Adsorption Desorption

We used natural resources of halloysite nanotubes and alginate to prepare a novel porous adsorption material of organic–inorganic hybrid beads. The adsorption behaviour of Cu(II) onto the hybrid beads was examined by a continuous fixed bed column adsorption experiment. Meanwhile, the factors affecting the adsorption capacity such as bed height, influent concentration and flow rate were investigated. The adsorption capacity (Q0) reached 74.13 mg/g when the initial inlet concentration was 100 mg/L with a bed height of 12 cm and flow rate of 3 ml/min. The Thomas model and bed-depth service time fitted well with the experimental data. In the regeneration experiment, the hybrid beads retained high adsorption capacity after three adsorption–desorption cycles. Over the whole study, the new hybrid beads showed excellent adsorption and regeneration properties as well as favourable stability.

Sign in / Sign up

Export Citation Format

Share Document