scholarly journals Conjunctive Use of BTC and Batch Methods for Heavy Metal Transport

2020 ◽  
Author(s):  
Mohamed Fahmy Hussein ◽  
Hassan Khater
Keyword(s):  
Heavy Metal ◽  
Distribution Coefficient ◽  
Sandy Loam ◽  
Mathematical Formulation ◽  
Breakthrough Curves ◽  
Retardation Factor ◽  
Model Parameters ◽  
Dilute Solution ◽  
High Concentration ◽  
Point Pollution

Abstract Marginal sediments can be used to combat point-pollution by heavy metals in industrial zones. Such practice requires information on metal-concentration in the workshop discharge water. Knowledge about the reaction of the heavy metal with the sediment available in the landscape is of utmost importance. Modeling of batch experiments and breakthrough curves, BTC, supplies relevant information in this regard. We present the static batch results of Freundlich isotherms testing CdCl2 aqueous solutions equilibria with sandy loam sediments, along with column-data processed by the dynamic codes CfitM and CfitIM under saturated water flow conditions. Three Cd-concentrations (5, 20, and 40 ppm) were employed to investigate the conjunction of using two procedures for obtaining the pertinent parameters for the transport of such a heavy metal and the design of the adequate Cd-trap. The results showed the deviations of the two techniques due to differences in their theoretical concepts, mathematical formulation, and performance. The batch method showed utility in supplying first guesses for the retardation factor, R, to insert into the 4-parameter analytical code, CfitIM, applied for column BTC modeling. The iteratively-obtained-parameters of the Freundlich equation were then employed to generate the distribution coefficient, k d. The generated value was, in turn, used to get more fair guess for the retardation factor, R, to use as a fixed-value in the CfitIM code to get an in-depth insight into the BTC dynamics and to obtain the other pertinent model parameters. The BTC runs indicated that the concentration controls the distinctive adsorption and transport rate and behavior of the heavy metal in the sediment column. The most dilute solution offered the highest Cd impediment, as shown by the most significant values for the distribution coefficient, k d, and retardation factor, R. The malfunction of the sediment as a trap appeared at Cd-concentrations four to eight folds higher than the most dilute solution. However, the loamy sand trap is successful when fed with a dilute aqueous solution. A set of successive traps is to arrange in tandem lines when moderate to high concentration is to discharge from an industrial workshop. The results emphasize the utility of the mutual use of these two lab procedures for the design of adequate traps and landfills and the simulation of more complex situations in the field. The point-pollution control needs to continue running batch and BTC experiments and to carry out their corresponding modeling.

scholarly journals Conjunctive Use of BTC and Batch Methods for Heavy Metal Transport

2020 ◽  
Author(s):  
Mohamed Fahmy Hussein ◽  
Hassan Khater
Keyword(s):  
Heavy Metal ◽  
Distribution Coefficient ◽  
Sandy Loam ◽  
Mathematical Formulation ◽  
Breakthrough Curves ◽  
Retardation Factor ◽  
Model Parameters ◽  
Dilute Solution ◽  
High Concentration ◽  
Point Pollution

Abstract Marginal sediments can be used to combat point-pollution by heavy metals in industrial zones. Such practice requires information on metal-concentration in the workshop discharge water. Knowledge about the reaction of the heavy metal with the sediment available in the landscape is of utmost importance. Modeling of batch experiments and breakthrough curves, BTC, supplies relevant information in this regard. We present the static batch results of Freundlich isotherms testing CdCl2 aqueous solutions equilibria with sandy loam sediments, along with column-data processed by the dynamic codes CfitM and CfitIM under saturated water flow conditions. Three Cd-concentrations (5, 20, and 40 ppm) were employed to investigate the conjunction of using two procedures for obtaining the pertinent parameters for the transport of such a heavy metal and the design of the adequate Cd-trap. The results showed the deviations of the two techniques due to differences in their theoretical concepts, mathematical formulation, and performance. The batch method showed utility in supplying first guesses for the retardation factor, R, to insert into the 4-parameter analytical code, CfitIM, applied for column BTC modeling. The iteratively-obtained-parameters of the Freundlich equation were then employed to generate the distribution coefficient, k d. The generated value was, in turn, used to get more fair guess for the retardation factor, R, to use as a fixed-value in the CfitIM code to get an in-depth insight into the BTC dynamics and to obtain the other pertinent model parameters. The BTC runs indicated that the concentration controls the distinctive adsorption and transport rate and behavior of the heavy metal in the sediment column. The most dilute solution offered the highest Cd impediment, as shown by the most significant values for the distribution coefficient, k d, and retardation factor, R. The malfunction of the sediment as a trap appeared at Cd-concentrations four to eight folds higher than the most dilute solution. However, the loamy sand trap is successful when fed with a dilute aqueous solution. A set of successive traps is to arrange in tandem lines when moderate to high concentration is to discharge from an industrial workshop. The results emphasize the utility of the mutual use of these two lab procedures for the design of adequate traps and landfills and the simulation of more complex situations in the field. The point-pollution control needs to continue running batch and BTC experiments and to carry out their corresponding modeling.

scholarly journals Conjunctive Use of BTC and Batch Methods for Heavy Metal Transport

2020 ◽  
Author(s):  
Mohamed Fahmy Hussein ◽  
Hassan Khater
Keyword(s):  
Heavy Metal ◽  
Distribution Coefficient ◽  
Sandy Loam ◽  
Mathematical Formulation ◽  
Breakthrough Curves ◽  
Retardation Factor ◽  
Model Parameters ◽  
Dilute Solution ◽  
High Concentration ◽  
Theoretical Concepts

Abstract Marginal sediments can be used to combat punctual pollution by heavy metals in industrial zones. Such practice requires information on metal-concentration in the workshop discharge water. Knowledge about the reaction of the heavy metal with the sediment available in the landscape is of utmost importance. Modeling of batch experiments and breakthrough curves, BTC, supplies relevant information in this regard. We modeled the static batch-data by Freundlich isotherms for testing CdCl2 aqueous solutions equilibria with sandy loam sediment and the dynamic column-data by two codes, CfitM and CfitIM, under saturated water flow conditions. Three Cd-concentrations (5, 20, and 40 ppm) were employed to investigate the conjunction of using two procedures for obtaining the pertinent parameters for the transport of such a heavy metal and the design of the adequate Cd-trap. The results showed the deviations of the two techniques due to differences in their theoretical concepts, mathematical formulation, and performance. The batch method showed utility in supplying first guesses for the retardation factor, R, to insert into the 4-parameter analytical code, CfitIM, applied for column BTC modeling. The iteratively-obtained-parameters of the Freundlich equation were then employed to generate the distribution coefficient, k d. The generated value was, in turn, used to get more fair guess for the retardation factor, R, to use as a fixed-value in the CfitIM code to get an in-depth insight into the BTC dynamics and to obtain the other pertinent model parameters. The BTC runs indicated that the concentration controls the distinctive adsorption and transport rate and behavior of the heavy metal in the sediment column. The most dilute solution offered the highest Cd impediment, as shown by the most significant values for the distribution coefficient, k d, and retardation factor, R. The malfunction of the sediment as a trap appeared at Cd-concentrations four to eight folds higher than the most dilute solution. However, the loamy sand trap is successful when fed with a dilute aqueous solution. A set of successive traps is to arrange in tandem lines when moderate to high concentration is to discharge from an industrial workshop. The results emphasize the utility of the mutual use of these two lab procedures for the design of adequate traps and landfills and the simulation of more complex situations in the field. The point-pollution control needs to continue running batch and BTC experiments and to carry out their corresponding modeling.

Parameter Determination for Chloride and Tritium Transport in Undisturbed Lysimeters during Steady Flow

1992 ◽  
Vol 23 (2) ◽  
pp. 89-104 ◽  
Author(s):  
Ole H. Jacobsen ◽  
Feike J. Leij ◽  
Martinus Th. van Genuchten
Keyword(s):  
Experimental Data ◽  
Unsaturated Flow ◽  
Transport Model ◽  
Time Moment ◽  
Breakthrough Curves ◽  
Coarse Sand ◽  
Retardation Factor ◽  
Parameter Determination ◽  
Model Parameters ◽  
Water Fraction

Breakthrough curves of Cl and 3H2O were obtained during steady unsaturated flow in five lysimeters containing an undisturbed coarse sand (Orthic Haplohumod). The experimental data were analyzed in terms of the classical two-parameter convection-dispersion equation and a four-parameter two-region type physical nonequilibrium solute transport model. Model parameters were obtained by both curve fitting and time moment analysis. The four-parameter model provided a much better fit to the data for three soil columns, but performed only slightly better for the two remaining columns. The retardation factor for Cl was about 10 % less than for 3H2O, indicating some anion exclusion. For the four-parameter model the average immobile water fraction was 0.14 and the Peclet numbers of the mobile region varied between 50 and 200. Time moments analysis proved to be a useful tool for quantifying the break through curve (BTC) although the moments were found to be sensitive to experimental scattering in the measured data at larger times. Also, fitted parameters described the experimental data better than moment generated parameter values.

scholarly journals Assessment of The Dioxins Leaching Potentials In Selected Soils Through Breakthrough Curves (BTCs) Model

2021 ◽  
Author(s):  
Nida Gul ◽  
Bushra Khan ◽  
Ishaq Ahmad Mian Kakakhel ◽  
Syed Muhammad Mukarram Shah ◽  
Muhammad Saeed ◽  
...  
Keyword(s):  
Distribution Coefficient ◽  
Solute Transport ◽  
Groundwater Contamination ◽  
Breakthrough Curve ◽  
Breakthrough Curves ◽  
Retardation Factor ◽  
Normal Velocity ◽  
Soil Series ◽  
Seepage Velocity ◽  
Local Soil

Abstract The current study was to investigate the leaching and groundwater contamination potential of selected Dioxins, in local soil series. Solute transport was modelled through Breakthrough curve (BTC) plots, based on distribution coefficient (Kd), Retardation factor and Dispersivity, under normal velocity (20 cm day -1) and preferential or steady flow (50 cm day -1). In case of Dibenzo -p- Dioxin (DD), distribution coefficient values were found in order of Charsadda > Peshawar > Sultanpur series, while for 2 Chloro- p- Dioxin (2Cl-DD), the order was Charsadda > Sultanpur > Peshawar. However, the overall sorption was low. Under the normal velocity both of selected Dioxins (DD & 2Cl-DD), BTC plots relatively took longer time to reach the point of saturation as compared to high seepage velocity. However, the overall solute transport was found to be rapid. This behaviour showed that sorption of the Dioxins selected soil series is low and there is potential for leaching and groundwater contamination.

ASSESSMENT OF HEAVY METAL CONCENTRATION IN COCONUT WATER

1970 ◽  
pp. 07-10
Author(s):  
MdDidarul Islam, Ashiqur Rahaman, Aboni Afrose
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Heavy Metal Concentration ◽  
Coconut Water ◽  
Toxic Heavy Metals ◽  
High Concentration ◽  
Toxic Heavy Metal ◽  
Low Concentration ◽  
Wet Ashing ◽  
Aas Method

This study was based on determining concentration of essential and toxic heavy metal in coconut water available at a local Hazaribagh area in Dhaka, Bangladesh. All essential minerals, if present in the drinking water at high concentration or very low concentration, it has negative actions. In this study, fifteen samples and eight heavy metals were analyzed by Atomic Absorption Spectroscopy (AAS) method which was followed by wet ashing digestion method. The concentration obtained in mg/l were in the range of 0.3 to 1.5, 7.77 to 21.2, 0 to 0.71, 0 to 0.9, 0 to 0.2, 0.9 to 17.3, 0.1 to 0.9, 0 to 0.9 and 0 to 0.7 for Fe, Ni, Cu, Cd, Cr, Zn, Pb and Se respectively. From this data it was concluded that any toxic heavy metals like Cd, Cr, Pb and Ni exceed their toxicity level and some essential nutrients were in low concentration in those samples. 

Phosphorus transport in saturated slag columns: experiments and mathematical models

1996 ◽  
Vol 34 (1-2) ◽  
pp. 153-160 ◽  
Author(s):  
S. H. Lee ◽  
S. Vigneswaran ◽  
K. Bajracharya
Keyword(s):  
Mathematical Models ◽  
Sorption Capacity ◽  
Algal Blooms ◽  
Sandy Loam ◽  
Dynamic Condition ◽  
Water Environment ◽  
Breakthrough Curves ◽  
Column Experiments ◽  
Phosphorus Transport ◽  
Waste Products

Excessive phosphorus (P as orthophosphate) is one of the major pollutants in natural water that are responsible for algal blooms and eutrophication. P removal by slag is an attractive solution if the P sorption capacity of slag is significant. To design an efficient land treatment facility, basic information on the behaviour of P in the media-water environment is required. In this study, detailed column experiments were conducted to study the P transport under dynamic condition, and mathematical models were developed to describe this process. The column experiments conducted with dust and cake waste products (slag) from a steel industry as adsorbing indicated that they had higher sorption capacity of P than that of a sandy loam soil from North Sydney, Australia. P transport in the dust and cake columns exhibited characteristic S-shaped or curvilinear breakthrough curves. The simulated results from a dynamic physical nonequilibrium sorption model (DPNSM) and Freundlich isotherm constants satisfactorily matched the corresponding experimental breakthrough data. The mobility of P is restricted by the adsorbents and it is proportional to the sorption capacity of them.

Modelling heavy metal mobilisation in solid waste deposits - a predictive tool for environmental risk assessment

1999 ◽  
Vol 39 (10-11) ◽  
pp. 193-196
Author(s):  
J. Petersen ◽  
J. G. Petrie
Keyword(s):  
Heavy Metal ◽  
Solid Waste ◽  
Environmental Risk ◽  
Mechanistic Model ◽  
Small Sample ◽  
Waste Material ◽  
Metal Species ◽  
Model Parameters ◽  
Assessment Methodology ◽  
Predictive Tool

The release of heavy metal species from deposits of solid waste materials originating from minerals processing operations poses a serious environmental risk should such species migrate beyond the boundaries of the deposit into the surrounding environment. Legislation increasingly places the liability for wastes with the operators of the process that generates them. The costs for long-term monitoring and clean-up following a potential critical leakage have to be factored in the overall project plan from the outset. Thus assessment of the potential for a particular waste material to generate a harmful leachate is directly relevant for estimating the environmental risk associated with the planned disposal operation. A rigorous mechanistic model is proposed, which allows prediction of the time-dependent generation of a leachate from a solid mineral waste deposit. Model parameters are obtained from a suitably designed laboratory waste assessment methodology on a relatively small sample of the prospective waste material. The parameters are not specific to the laboratory environment in which they were obtained but are valid also for full-scale heap modelling. In this way the model, combined with the assessment methodology, becomes a powerful tool for meaningful assessment of the risks associated with solid waste disposal strategies.

Transport of Microorganisms in the Underground – Processes, Experiments and Simulation Models

1991 ◽  
Vol 24 (2) ◽  
pp. 309-314 ◽  
Author(s):  
G. Teutsch ◽  
K. Herbold-Paschke ◽  
D. Tougianidou ◽  
T. Hahn ◽  
K. Botzenhart
Keyword(s):  
Simulation Models ◽  
Mass Conservation ◽  
Breakthrough Curves ◽  
Conservation Equation ◽  
Retardation Factor ◽  
Natural Systems ◽  
Laboratory Setup ◽  
Preliminary Model ◽  
Sand And Gravel ◽  
Mass Conservation Equation

In this paper the major processes governing the persistence and underground transport of viruses and bacteria are reviewed in respect to their importance under naturally occurring conditions. In general, the simulation of the governing processes is based on the macroscopic mass-conservation equation with the addition of some filter and/or retardation factor and a decay coefficient, representing the natural “die-off” of the microorganisms. More advanced concepts try to incorporate growth and decay coefficients together with deposition and declogging factors. At present, none of the reported concepts has been seriously validated. Due to the complexity of natural systems and the pathogenic properties of some of the microorganisms, experiments under controlled laboratory conditions are required. A laboratory setup is presented in which a great variety of natural conditions can be simulated. This comprises a set of 1 metre columns and an 8 metre stainless-steel flume with 24 sampling ports. The columns are easily filled and conditioned and therefore used to study the effects of different soil-microorganism combinations under various environmental conditions. In the artificial flume natural underground conditions are simulated using sand and gravel aquifer material from the river Neckar alluvium. A first set of results from the laboratory experiments is presented together with preliminary model simulations. The large variety of observed breakthrough curves and recovery for the bacteria and viruses under investigation demonstrates the great uncertainty encountered in microbiological risk assessment.

Spatial Distribution of Heavy Metal Ions in Glass Forming Melts: Spectroscopic and Physical-Chemical Study

2008 ◽  
Vol 39-40 ◽  
pp. 41-44 ◽  
Author(s):  
A. Anan’ev ◽  
L. Maksimov
Keyword(s):  
Heavy Metal ◽  
Spatial Distribution ◽  
Metal Ions ◽  
Distribution Coefficient ◽  
Heavy Metal Ions ◽  
Brillouin Scattering ◽  
Chemical Study ◽  
Sodium Borate ◽  
Glass Host ◽  
Glass Forming

Spatial distribution of heavy metal ions (HMI) in inorganic glass forming melts was studied by measuring HMI distribution coefficient between two unmixable melts: sodium-borate glass forming melt and non-glass forming molten sodium sulfate. Combining the data on glass host composition dependence of HMI distribution coefficient with the data of Rayleigh and Mandel’shtam-Brillouin scattering (RMBS) spectroscopy of glasses doped with HMI and undoped ones made it possible to evidence the segregation of HMI into alkali-enriched inhomogeneities of glass hosts and offer the approach to choosing compositions of glass host in which HMI segregation will be minimized.

Separation of Heavy Metal Ions from the Solution Obtained by Leaching Low-Grade Pyrolusite with Pyrite and H2SO4

2013 ◽  
Vol 773 ◽  
pp. 283-288
Author(s):  
Xing Zou ◽  
Xiang Quan Chen ◽  
Hai Chao Xie ◽  
Xiao Dan Qiu
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Heavy Metal Ions ◽  
Separation Efficiency ◽  
Ph Value ◽  
Sulfate Solution ◽  
Ion Concentration ◽  
Manganese Sulfate ◽  
Low Grade ◽  
High Concentration

The manganese sulfate solution leached from low-grade pyrolusite with pyrite and H2SO4 contains heavy metal ions of high concentration, influencing the quality of the final products of manganese compounds and causing manganese ions not to be electrolyzed. The present study was focused on the separation of Co, Ni and Zn ions from the leached solution with BaS. By controlling the pH value at 5.0-6.5, temperature at 50-60°C, reaction time at 15 min and mixing velocity at 78 rpm, the heavy metal ions could be separated effectively. Under the above optimized conditions, the ion concentration of Co, Ni, and Zn in the solution was reduced to 0.06 mg.L-1, 0.27mg.L-1 and 0.01mg.L-1, and the separation efficiency was 99.72%, 99.18% and 99.9% respectively. The obtained pure solution meets the demands of manganese electrowinning.

Sign in / Sign up

Export Citation Format

Share Document